Михаил Вячеславович Маркушев
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Михаил Вячеславович Маркушев has a total of 65 co-authors. Here are the top co-authors by number of shared publications:
- E. V. Avtokratova
Institute for Metals Superplasticity Problems of the Russian Academy of Sciences, Ufa, Russian Federation
10 shared publications - Stanislav Vatslavovich Krymskiy
Institute for Metals Superplasticity Problems of the Russian Academy of Sciences, Ufa, Russian Federation
7 shared publications O Sh Sitdikov
Institute for Metals Superplasticity Problems, 39 Khalturin St., Ufa 450001, Russia
5 shared publications- Oleg Sitdikov
Russian Academy of Sciences
5 shared publications E V Avtokratova
Institute for Metals Superplasticity Problems, Khalturin st. 39, Ufa 450001, Russia
4 shared publications- Mikhail Linderov
Togliatti State University
4 shared publications
Latest Publications
- 1 February 2026
- Published by Pleiades Publishing Ltd in Russian Journal of Non-Ferrous Metals
- Vol. 67 (1) , 31-37
Visualization of the Skin-Effect under Electric Pulsing and Its Influence on Structure and Strength of Cryorolled Aluminum Alloy
Using a high-speed thermal imaging camera, the temperature field on the surface of a 3 × 3 mm square sample of cryorolled high-strength aluminum alloy was recorded and analyzed during high-dense electropulsed processing. Uneven heating of the surface was observed, manifested by elevated temperatures in areas adjacent to the fins. The results of a comparative analysis of the alloy microstructure changes by SEM-EBSD method and the microhardness distributions along the specimen cross-section, induced by a current pulsing, are discussed. It was found that in zones of increased heating adjacent to the specimen’s surfaces, static processes of recovery and recrystallization of the highly work-hardened structure were more intense and accompanied by greater softening. It is concluded that this phenomenon is caused by the skin-effect inherent to electropulse treatment. Good agreement is demonstrated between the depth of the softened layer and the calculated current penetration depth into the conductor.
- 1 February 2026
- Published by Pleiades Publishing Ltd in Russian Journal of Non-Ferrous Metals
- Vol. 67 (1) , 31-37
Visualization of the Skin-Effect under Electric Pulsing and Its Influence on Structure and Strength of Cryorolled Aluminum Alloy
Using a high-speed thermal imaging camera, the temperature field on the surface of a 3 × 3 mm square sample of cryorolled high-strength aluminum alloy was recorded and analyzed during high-dense electropulsed processing. Uneven heating of the surface was observed, manifested by elevated temperatures in areas adjacent to the fins. The results of a comparative analysis of the alloy microstructure changes by SEM-EBSD method and the microhardness distributions along the specimen cross-section, induced by a current pulsing, are discussed. It was found that in zones of increased heating adjacent to the specimen’s surfaces, static processes of recovery and recrystallization of the highly work-hardened structure were more intense and accompanied by greater softening. It is concluded that this phenomenon is caused by the skin-effect inherent to electropulse treatment. Good agreement is demonstrated between the depth of the softened layer and the calculated current penetration depth into the conductor.
- Open Access
- 19 December 2025
- Published by University of Nis in Facta Universitatis, Series: Mechanical Engineering
- Vol. 23 (4) , 909-920
EFFECT OF ELECTRIC PULSING ON THE STRUCTURE, TEXTURE AND HARDNESS OF CRYOROLLED FINE-GRAIN COPPER
A synergy effect of cryorolling and high-dense electric pulsing on the structure, texture and hardness of fine-grain Cu is analyzed. More than twice Cu strengthening under rolling with 90% reduction at –196°С was caused by strong rolling texture and work-hardened nanostructure with ~300 nm crystallites and ~30% fraction of high-angle boundaries. Further single pulsing with current intensity Kj = 3.5×104 A2s/mm4 resulted in a static recovery and slight Cu softening due to the formation of a more equilibrium structure with lower dislocation density and lattice microstrain. Increasing Kj to 3.8×104 A2s/mm4 led to a sharp drop in the Cu hardness owing to continuous recrystallization and texture randomization. At Kj near 5.0×104 A2s/mm4 homogeneous ultrafine-grain structure with 1 μm defect free equiaxed grains and about 30% of twin boundaries is formed. Normal grain growth to 3 µm and gradual decrease of the Cu hardness were taking place at higher pulsing energies, up to 8.1×104 A2s/mm4.
- 19 December 2025
- Published by University of Nis in Facta Universitatis, Series: Mechanical Engineering
- Vol. 23 (4) , 909-920
Open AccessEFFECT OF ELECTRIC PULSING ON THE STRUCTURE, TEXTURE AND HARDNESS OF CRYOROLLED FINE-GRAIN COPPER
A synergy effect of cryorolling and high-dense electric pulsing on the structure, texture and hardness of fine-grain Cu is analyzed. More than twice Cu strengthening under rolling with 90% reduction at –196°С was caused by strong rolling texture and work-hardened nanostructure with ~300 nm crystallites and ~30% fraction of high-angle boundaries. Further single pulsing with current intensity Kj = 3.5×104 A2s/mm4 resulted in a static recovery and slight Cu softening due to the formation of a more equilibrium structure with lower dislocation density and lattice microstrain. Increasing Kj to 3.8×104 A2s/mm4 led to a sharp drop in the Cu hardness owing to continuous recrystallization and texture randomization. At Kj near 5.0×104 A2s/mm4 homogeneous ultrafine-grain structure with 1 μm defect free equiaxed grains and about 30% of twin boundaries is formed. Normal grain growth to 3 µm and gradual decrease of the Cu hardness were taking place at higher pulsing energies, up to 8.1×104 A2s/mm4.
- 30 June 2025
- Published by Pleiades Publishing Ltd in Physical Mesomechanics
- Vol. 28 (3) , 381-396
Nanostructuring, Structure Heterogeneity, and Static Strength of Complex Aluminum Alloys
The phenomenology and nature of two-level (matrix and second phases) nanostructuring of complex aluminum alloys during thermomechanical processing based on cold severe plastic deformation are considered. The importance of taking into account the principle of structure heterogeneity optimization at all stages of processing by controlling the parameters of second phases is substantiated. A number of conclusions are formulated that can be used as the basis for the criteria of this principle for the alloy treatment involving severe plastic deformation to ensure its effective nanostructuring and property enhancement. A new approach to classification of nanostructured alloys is proposed.
- 30 June 2025
- Published by Pleiades Publishing Ltd in Physical Mesomechanics
- Vol. 28 (3) , 381-396
Nanostructuring, Structure Heterogeneity, and Static Strength of Complex Aluminum Alloys
The phenomenology and nature of two-level (matrix and second phases) nanostructuring of complex aluminum alloys during thermomechanical processing based on cold severe plastic deformation are considered. The importance of taking into account the principle of structure heterogeneity optimization at all stages of processing by controlling the parameters of second phases is substantiated. A number of conclusions are formulated that can be used as the basis for the criteria of this principle for the alloy treatment involving severe plastic deformation to ensure its effective nanostructuring and property enhancement. A new approach to classification of nanostructured alloys is proposed.
- 6 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-8
Structure and mechanical properties of Al–5%Mg–Sc–Zr alloy after cryogenic deformation
- 6 January 2025
- Published by Springer Nature in Russian Physics Journal
- p. 1-8
Structure and mechanical properties of Al–5%Mg–Sc–Zr alloy after cryogenic deformation
- Open Access
- 20 December 2023
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 20 (4) , 491-500
МИКРОСТРУКТУРНЫЕ ИЗМЕНЕНИЯ В СПЛАВЕ Al-3 вес. % Cu В ПРОЦЕССЕ РАВНОКАНАЛЬНОГО УГЛОВОГО ПРЕССОВАНИЯ ПРИ ПОВЫШЕННОЙ ТЕМПЕРАТУРЕ
Исследовали изменение микроструктуры крупнозернистого бинарного сплава Al-3 вес. % Cu в процессе равноканального углового (РКУ) прессования при Т=150 °C ≈ 0,5Тпл (где Tпл – температура плавления чистого алюминия). Перед началом деформации в сплаве были получены гомогенные выделения упрочняющей фазы Q(Al2Cu) со средним размером около 16 нм. Как и в условиях низкотемпературной деформации, основной особенностью РКУ прессования данного сплава при 0,5Тпл было развитие на начальной стадии деформации (e=1) полосовых деформационных структур, приводящих к фрагментации исходных зерен. Однако, при дальнейшем РКУ прессовании такие дислокационные структуры трансформировались в характерную для горячей деформации смешанную (суб)зеренную структуру, что сопровождалось измельчением зерен. В результате при e=8 в сплаве формировалась бимодальная микроструктура с долей высокоугловых границ около 50 %, состоящая на 60 % из областей новых зерен размером около 1 мкм и нерекристаллизованных фрагментов исходных зерен, содержащих субзерна. Показано, что в отсутствие дисперсных алюминидов переходных металлов выделения основной упрочняющей фазы Q оказывали существенное влияние на процессы накопления и релаксации энергии деформации. В результате эти выделения контролировали формирование дислокационной структуры, протекание динамического возврата и миграцию границ (суб)зерен, определяя характер и кинетику процессов формирования новой мелкозернистой структуры.
- 20 December 2023
- Published by Altai State Technical University in Фундаментальные проблемы современного материаловедения
- Vol. 20 (4) , 491-500
Open AccessМИКРОСТРУКТУРНЫЕ ИЗМЕНЕНИЯ В СПЛАВЕ Al-3 вес. % Cu В ПРОЦЕССЕ РАВНОКАНАЛЬНОГО УГЛОВОГО ПРЕССОВАНИЯ ПРИ ПОВЫШЕННОЙ ТЕМПЕРАТУРЕ
Исследовали изменение микроструктуры крупнозернистого бинарного сплава Al-3 вес. % Cu в процессе равноканального углового (РКУ) прессования при Т=150 °C ≈ 0,5Тпл (где Tпл – температура плавления чистого алюминия). Перед началом деформации в сплаве были получены гомогенные выделения упрочняющей фазы Q(Al2Cu) со средним размером около 16 нм. Как и в условиях низкотемпературной деформации, основной особенностью РКУ прессования данного сплава при 0,5Тпл было развитие на начальной стадии деформации (e=1) полосовых деформационных структур, приводящих к фрагментации исходных зерен. Однако, при дальнейшем РКУ прессовании такие дислокационные структуры трансформировались в характерную для горячей деформации смешанную (суб)зеренную структуру, что сопровождалось измельчением зерен. В результате при e=8 в сплаве формировалась бимодальная микроструктура с долей высокоугловых границ около 50 %, состоящая на 60 % из областей новых зерен размером около 1 мкм и нерекристаллизованных фрагментов исходных зерен, содержащих субзерна. Показано, что в отсутствие дисперсных алюминидов переходных металлов выделения основной упрочняющей фазы Q оказывали существенное влияние на процессы накопления и релаксации энергии деформации. В результате эти выделения контролировали формирование дислокационной структуры, протекание динамического возврата и миграцию границ (суб)зерен, определяя характер и кинетику процессов формирования новой мелкозернистой структуры.
- 1 November 2023
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2023 (11) , 1690-1695
Effect of High-Dense Electropulsing on Structure and Strength of Cryorolled Metals
A comparative analysis of changes in structure and ambient temperature mechanical behavior of pure FCC metals—Al, Ni and Cu, due to high-dense electropulsing (HDEP) of isothermally cryorolled at liquid nitrogen temperature sheets, has been carried out. Processes, driving forces and factors controlling the nature and kinetics of transformation of the deformation structure during HDEP are discussed. Temperature ranges of activation of recovery and recrystallization in the cryorolled metals under pulsing of different capacity are determined. It is shown that the processing allows controlling strength of metals within a wide range owing to formation of homogeneous and/or heterogeneous structures with different crystallite size, dislocation density and grain boundary spectrum, involving ultra-fine grained and nanostructured ones. It is concluded that the phenomenology and nature of metal softening under electric pulsing are similar to those, occurred at conventional furnace annealing.
- 1 November 2023
- Published by Pleiades Publishing Ltd in Russian Metallurgy (Metally)
- Vol. 2023 (11) , 1690-1695
Effect of High-Dense Electropulsing on Structure and Strength of Cryorolled Metals
A comparative analysis of changes in structure and ambient temperature mechanical behavior of pure FCC metals—Al, Ni and Cu, due to high-dense electropulsing (HDEP) of isothermally cryorolled at liquid nitrogen temperature sheets, has been carried out. Processes, driving forces and factors controlling the nature and kinetics of transformation of the deformation structure during HDEP are discussed. Temperature ranges of activation of recovery and recrystallization in the cryorolled metals under pulsing of different capacity are determined. It is shown that the processing allows controlling strength of metals within a wide range owing to formation of homogeneous and/or heterogeneous structures with different crystallite size, dislocation density and grain boundary spectrum, involving ultra-fine grained and nanostructured ones. It is concluded that the phenomenology and nature of metal softening under electric pulsing are similar to those, occurred at conventional furnace annealing.
- Open Access
- 1 January 2023
- Published by Togliatti State University in Frontier materials & technologies
- No. 4,p. 53-62
Combination of cryogenic deformation and electropulse processing as a way to produce ultrafine-grain metals
The data of a comparative analysis of the structure and hardness of pure metals with a face-centered cubic lattice – aluminum, nickel and copper, subjected to complex thermomechanical treatment (TMT), including isothermal cryogenic rolling at liquid nitrogen temperature and subsequent high-density electropulse treatment (EPT) were presented. The main stages, features and advantages of TMT, which first ensure strong work hardening of the processed material due to deformation at low temperatures and then its ultra-fast contact electropulse heating up to a specified temperature, were considered. A multi-level analysis of the metals structure evolution due to TMT was carried out using modern methods of scanning electron microscopy and X-ray diffractometry, recording a wide range of its linear and angular parameters. The kinetics and nature of the processes of the metals structure evolution under cryogenic rolling and EPT, their driving forces and controlling factors, as well as general patterns and temperature intervals of activation of the deformation structure recovery and recrystallization influenced by an electric pulse are identified and discussed. Based on the results of the analysis of the structural and mechanical behaviour of metals, it was concluded that the combination of severe plastic cryogenic deformation and a single-step treatment with ultrashort alternating current pulses is an effective way to obtain semi-finished products with controlled parameters of their structure and properties, including high-strength ultrafine-grain rolled products. At that the phenomenology and nature of the strengthening/softening of metals during cryogenic rolling and subsequent electropulsing are similar to those observed under cold rolling and furnace annealing.
- 1 January 2023
- Published by Togliatti State University in Frontier materials & technologies
- No. 4,p. 53-62
Open AccessCombination of cryogenic deformation and electropulse processing as a way to produce ultrafine-grain metals
The data of a comparative analysis of the structure and hardness of pure metals with a face-centered cubic lattice – aluminum, nickel and copper, subjected to complex thermomechanical treatment (TMT), including isothermal cryogenic rolling at liquid nitrogen temperature and subsequent high-density electropulse treatment (EPT) were presented. The main stages, features and advantages of TMT, which first ensure strong work hardening of the processed material due to deformation at low temperatures and then its ultra-fast contact electropulse heating up to a specified temperature, were considered. A multi-level analysis of the metals structure evolution due to TMT was carried out using modern methods of scanning electron microscopy and X-ray diffractometry, recording a wide range of its linear and angular parameters. The kinetics and nature of the processes of the metals structure evolution under cryogenic rolling and EPT, their driving forces and controlling factors, as well as general patterns and temperature intervals of activation of the deformation structure recovery and recrystallization influenced by an electric pulse are identified and discussed. Based on the results of the analysis of the structural and mechanical behaviour of metals, it was concluded that the combination of severe plastic cryogenic deformation and a single-step treatment with ultrashort alternating current pulses is an effective way to obtain semi-finished products with controlled parameters of their structure and properties, including high-strength ultrafine-grain rolled products. At that the phenomenology and nature of the strengthening/softening of metals during cryogenic rolling and subsequent electropulsing are similar to those observed under cold rolling and furnace annealing.
- 1 December 2022
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 12 (4) , 409-413
Effect of strain of cryorolling on structure and strength of nickel
The effect of isothermal rolling at liquid nitrogen temperature with reductions up to 90 % on the structural-mechanical behavior of coarse-grained nickel was evaluated by TEM, SEM-EBSD and X-ray analysis methods, and microhardness measurements. The highest hardening rate of the metal was found at the initial stage of rolling (up to about 50 %), after which it decreased slightly with further reductions. Detailed analyses of the evolution of dislocation density, grain size and grain boundary spectra have shown that the behavior found was attributed to an extremely low deformation temperature, resulted in a decreased rate of accumulation of crystalline defects, as well as the formation and rearrangement of dislocation structure. Due to the strong suppression of dynamic recovery and recrystallization, even when rolling to a reduction of 90 %, a relatively homogeneous coarse-fibered structure with a developed nanocellular substructure and less than 5 % fraction of nanoscale dynamically recrystallized grains was formed. It was concluded that the main structural strengthening factors in cryogenically rolled nickel was the formation of low-energy dislocation structures and their transformations into a welldeveloped substructure with nanosized crystallites separated predominantly by low-angle boundaries.
- 1 December 2022
- Published by Institute for Metals Superplasticity Problems of RAS in Letters on Materials
- Vol. 12 (4) , 409-413
Effect of strain of cryorolling on structure and strength of nickel
The effect of isothermal rolling at liquid nitrogen temperature with reductions up to 90 % on the structural-mechanical behavior of coarse-grained nickel was evaluated by TEM, SEM-EBSD and X-ray analysis methods, and microhardness measurements. The highest hardening rate of the metal was found at the initial stage of rolling (up to about 50 %), after which it decreased slightly with further reductions. Detailed analyses of the evolution of dislocation density, grain size and grain boundary spectra have shown that the behavior found was attributed to an extremely low deformation temperature, resulted in a decreased rate of accumulation of crystalline defects, as well as the formation and rearrangement of dislocation structure. Due to the strong suppression of dynamic recovery and recrystallization, even when rolling to a reduction of 90 %, a relatively homogeneous coarse-fibered structure with a developed nanocellular substructure and less than 5 % fraction of nanoscale dynamically recrystallized grains was formed. It was concluded that the main structural strengthening factors in cryogenically rolled nickel was the formation of low-energy dislocation structures and their transformations into a welldeveloped substructure with nanosized crystallites separated predominantly by low-angle boundaries.
- 27 November 2022
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 54 (2) , 505-525
Structural Characterization of Binary Al-Cu Alloy Processed by Equal Channel Angular Pressing at Half of the Melting Point
- 27 November 2022
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 54 (2) , 505-525
Structural Characterization of Binary Al-Cu Alloy Processed by Equal Channel Angular Pressing at Half of the Melting Point