Salim Nasar Faraj Mursal
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Salim Nasar Faraj Mursal has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Hammad Hussain
Department of Agricultural Engineering, Faculty of Agricultural Engineering & Technology, University of Agriculture Faisalabad, Faisalabad 38040, Pakistan
1 shared publication - Muawia Abdelkafi Magzoub
Department of Electrical Engineering, Sudan Technological University, National University 4 , 11111 Khartoum
1 shared publication - Muhammad Adnan Munir
State Key Laboratory for Mechanical Behavior of Materials, School of Materials Science and Engineering, Xi'an Jiaotong University, Xi'an, 710049, PR China
1 shared publication - Muhammad Irfan
Electrical Engineering Department, College of Engineering, Najran University, Najran, Kingdom of Saudi Arabia
1 shared publication - Muhammad Yasin Naz
Department of Physics, University of Agriculture, Faisalabad, Pakistan
1 shared publication - Noor Ul Ain
Department of Physics, University of Agriculture 2 , Faisalabad 38040, Pakistan
1 shared publication
Latest Publications
- Open Access
- 1 January 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (1)
Production and characterization of CuNiZnFe2O4 dispersed transformer and kerosene oil based magnetic nanofluids for heat transfer applications
This study produced nanofluids via a two-step method by dispersing copper–nickel–zinc (CuNiZnFe2O4) ferrite nanocomposites in transformer and kerosene oils. A sol–gel auto-combustion approach was adopted to synthesize ferrite nanoparticles. The prepared nanoparticles were analyzed through scanning electron microscopy, photoluminescence spectroscopy, and x-ray diffraction. The measured crystallite size varied between 11 and 13 nm. The SEM images show that the structures of the developed CuNiZn nanoparticles are irregular. The photoluminescence results give a bandgap of 1.91 eV and the emission lines of the nanoparticles. Transient hot wire analysis was performed to determine the thermal conductivity of the base fluid and the prepared nanofluids. It is observed that nanoparticles in the nanofluid enhance the heat transfer rate. It has been proven that CuNiZn/kerosene-based nanofluids have greater thermal conductivity than CuNiZn/transformer oil-based nanofluids. The viscosity of transformer oil-based nanofluids at room temperature is 12.53 mm2 s−1, which decreases to 12.49 mm2 s−1 at 40 °C. Similarly, the viscosity of kerosene-based nanofluids is 1.49 mm2 s−1 at room temperature and 1.16 mm2 s−1 at 40 °C. The sedimentation method revealed that CuNiZn/transformer oil-based nanofluids have greater stability than CuNiZn/kerosene-based nanofluids.
- 1 January 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (1)
Open AccessProduction and characterization of CuNiZnFe2O4 dispersed transformer and kerosene oil based magnetic nanofluids for heat transfer applications
This study produced nanofluids via a two-step method by dispersing copper–nickel–zinc (CuNiZnFe2O4) ferrite nanocomposites in transformer and kerosene oils. A sol–gel auto-combustion approach was adopted to synthesize ferrite nanoparticles. The prepared nanoparticles were analyzed through scanning electron microscopy, photoluminescence spectroscopy, and x-ray diffraction. The measured crystallite size varied between 11 and 13 nm. The SEM images show that the structures of the developed CuNiZn nanoparticles are irregular. The photoluminescence results give a bandgap of 1.91 eV and the emission lines of the nanoparticles. Transient hot wire analysis was performed to determine the thermal conductivity of the base fluid and the prepared nanofluids. It is observed that nanoparticles in the nanofluid enhance the heat transfer rate. It has been proven that CuNiZn/kerosene-based nanofluids have greater thermal conductivity than CuNiZn/transformer oil-based nanofluids. The viscosity of transformer oil-based nanofluids at room temperature is 12.53 mm2 s−1, which decreases to 12.49 mm2 s−1 at 40 °C. Similarly, the viscosity of kerosene-based nanofluids is 1.49 mm2 s−1 at room temperature and 1.16 mm2 s−1 at 40 °C. The sedimentation method revealed that CuNiZn/transformer oil-based nanofluids have greater stability than CuNiZn/kerosene-based nanofluids.