Vitalii V. Savushkin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Vitalii V. Savushkin has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
Hq Zhao
Jiangsu Maritime Institute , China
1 shared publication- Marek Dzida
Gdansk University of Technology , Gdansk , Poland
1 shared publication Serhiy I. Serbin
1 shared publication- Serhiy Ivanovich Serbin
Admiral Makarov National University of Shipbuilding , Mykolaiv , Ukraine
1 shared publication С. І. Сербін
Admiral Makarov National University of Shipbuilding
1 shared publication
Latest Publications
- 2 November 2026
- Published by Admiral Makarov National University of Shipbuilding
- No. 3 (506),p. 97-106
СИНТЕТИЧНА ГЕНЕРАЦІЯ ДАНИХ ДЛЯ НЕЙРОМЕРЕЖЕВОГО МОНІТОРИНГУ ТЕПЛОВОГО СТАНУ ЛОПАТОК ГТД НА ОСНОВІ ФІЗИЧНООБҐРУНТОВАНИХ МОДЕЛЕЙ
One of the key challenges in developing proactive monitoring systems for gas turbine engine (GTE) components is the limited availability of representative experimental data covering the full range of operating conditions. This is particularly relevant for cooled high-pressure turbine (HPT) blades, which operate under extreme thermal loads and whose thermal state is determined by the complex interaction of multiple parameters of the cooling system. The aim of this study is to develop and substantiate a methodology for synthetic training data generation based on physically justified mathematical models of heat transfer for training a hybrid neural network intended for thermal state monitoring of cooled HPT working blades. The synthetic dataset was formed with uniform coverage of five input parameters: inlet gas temperature, cooling air pressure, cooling air temperature, cooling air flow rate, and gas flow pressure ratio. The mathematical model used for data generation is based on heat transfer criterion equations and was calibrated against existing experimental measurements. The present paper proposes a virtual instrumentation scheme comprising thirty thermocouples distributed across three characteristic blade cross-sections and one optical pyrometer was developed. The scientific novelty of the proposed approach lies in the development of a comprehensive and reproducible methodology that simultaneously accounts for spatially distributed thermocouple measurements across multiple characteristic blade cross-sections and the integral signal of an optical pyrometer – a combination that is typical for real thermo-hydraulic testing conditions but has not previously been systematically reproduced in synthetic datasets for neural network training. The practical significance of the results consists in the fact that the proposed methodology enables uniform coverage of the entire operating range, creation of a balanced dataset for all blade condition classes, and investigation of the individual influence of each cooling system parameter without conducting costly full-scale experiments. The results confirm that a hybrid neural network trained on the generated synthetic data achieves a coefficient of determination R2 > 0,99 and a mean absolute prediction error not exceeding 2 % of the operating temperature range, which confirms the adequacy of the methodology and its suitability for training neural network models for GTE blade thermal state monitoring.
- 2 November 2026
- Published by Admiral Makarov National University of Shipbuilding
- No. 3 (506),p. 97-106
СИНТЕТИЧНА ГЕНЕРАЦІЯ ДАНИХ ДЛЯ НЕЙРОМЕРЕЖЕВОГО МОНІТОРИНГУ ТЕПЛОВОГО СТАНУ ЛОПАТОК ГТД НА ОСНОВІ ФІЗИЧНООБҐРУНТОВАНИХ МОДЕЛЕЙ
One of the key challenges in developing proactive monitoring systems for gas turbine engine (GTE) components is the limited availability of representative experimental data covering the full range of operating conditions. This is particularly relevant for cooled high-pressure turbine (HPT) blades, which operate under extreme thermal loads and whose thermal state is determined by the complex interaction of multiple parameters of the cooling system. The aim of this study is to develop and substantiate a methodology for synthetic training data generation based on physically justified mathematical models of heat transfer for training a hybrid neural network intended for thermal state monitoring of cooled HPT working blades. The synthetic dataset was formed with uniform coverage of five input parameters: inlet gas temperature, cooling air pressure, cooling air temperature, cooling air flow rate, and gas flow pressure ratio. The mathematical model used for data generation is based on heat transfer criterion equations and was calibrated against existing experimental measurements. The present paper proposes a virtual instrumentation scheme comprising thirty thermocouples distributed across three characteristic blade cross-sections and one optical pyrometer was developed. The scientific novelty of the proposed approach lies in the development of a comprehensive and reproducible methodology that simultaneously accounts for spatially distributed thermocouple measurements across multiple characteristic blade cross-sections and the integral signal of an optical pyrometer – a combination that is typical for real thermo-hydraulic testing conditions but has not previously been systematically reproduced in synthetic datasets for neural network training. The practical significance of the results consists in the fact that the proposed methodology enables uniform coverage of the entire operating range, creation of a balanced dataset for all blade condition classes, and investigation of the individual influence of each cooling system parameter without conducting costly full-scale experiments. The results confirm that a hybrid neural network trained on the generated synthetic data achieves a coefficient of determination R2 > 0,99 and a mean absolute prediction error not exceeding 2 % of the operating temperature range, which confirms the adequacy of the methodology and its suitability for training neural network models for GTE blade thermal state monitoring.
- Open Access
- 18 November 2025
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 32 (4) , 78-86
Evaluation of the Thermal Condition of Marine Gas Turbine Components via Telemetric Measurements
This paper focuses on assessing the thermal state of a marine gas turbine plant (MGTP), with particular attention being given to the measurement of turbine rotor component temperatures using a specially developed telemetric measurement system (TMS). The study was conducted within the framework of research aimed at evaluating the effects of reduced relative air temperature, which is supplied by the high-pressure compressor (HPC) through nozzle guide vanes (NGV) and a twisting grid (TG) inside the rotor blades (RB) of a high-pressure turbine (HPT), on the thermal state of the HPT rotor. This temperature reduction is achieved via a pre-swirl technique, in which the cooling air is directed toward rotor rotation. The results obtained demonstrate new opportunities for monitoring the thermal condition of turbine components during the modernisation of MGTPs. This approach contributes to improving the overall efficiency of the system by enabling an increase in the gas flow temperature at the inlet to the HPT’s first stage.
- 18 November 2025
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 32 (4) , 78-86
Open AccessEvaluation of the Thermal Condition of Marine Gas Turbine Components via Telemetric Measurements
This paper focuses on assessing the thermal state of a marine gas turbine plant (MGTP), with particular attention being given to the measurement of turbine rotor component temperatures using a specially developed telemetric measurement system (TMS). The study was conducted within the framework of research aimed at evaluating the effects of reduced relative air temperature, which is supplied by the high-pressure compressor (HPC) through nozzle guide vanes (NGV) and a twisting grid (TG) inside the rotor blades (RB) of a high-pressure turbine (HPT), on the thermal state of the HPT rotor. This temperature reduction is achieved via a pre-swirl technique, in which the cooling air is directed toward rotor rotation. The results obtained demonstrate new opportunities for monitoring the thermal condition of turbine components during the modernisation of MGTPs. This approach contributes to improving the overall efficiency of the system by enabling an increase in the gas flow temperature at the inlet to the HPT’s first stage.
- 1 January 2025
- Published by Admiral Makarov National University of Shipbuilding in Collection of Scientific Publications NUS
- No. 2 (500),p. 104-110
DETERMINATION OF THE GAS TURBINE ENGINE THERMAL CONDITION ELEMENTS USING A TELEMETRY SYSTEM
- 1 January 2025
- Published by Admiral Makarov National University of Shipbuilding in Collection of Scientific Publications NUS
- No. 2 (500),p. 104-110
DETERMINATION OF THE GAS TURBINE ENGINE THERMAL CONDITION ELEMENTS USING A TELEMETRY SYSTEM
- Open Access
- 1 January 2023
- Published by Admiral Makarov National University of Shipbuilding in Collection of Scientific Publications NUS
- Vol. 493 (4) , 40-45
INVESTIGATION OF THE TEMPERATURE CONDITION OF THE GTE COMBUSTION CHAMBER FLAME TUBE USING THERMAL INDICATOR PAINTS AND THERMOCOUPLES
- 1 January 2023
- Published by Admiral Makarov National University of Shipbuilding in Collection of Scientific Publications NUS
- Vol. 493 (4) , 40-45
Open AccessINVESTIGATION OF THE TEMPERATURE CONDITION OF THE GTE COMBUSTION CHAMBER FLAME TUBE USING THERMAL INDICATOR PAINTS AND THERMOCOUPLES