Andreas Windischhofer
Research Subjects
Andreas Windischhofer has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Benedikt Schwarz
TU Wien
5 shared publications - Florian Pilat
Technische Universität Wien
3 shared publications - Gottfried Strasser
Institute of Solid State Electronics E362, Technische Universität Wien
2 shared publications - Johannes Fuchsberger
Institute of Solid State Electronics , TU Wien
2 shared publications - Josephine Nauschütz
Nanoplus Nanosystems and Technologies GmbH 2 , Gerbrunn
2 shared publications - Nikola Opačak
TU Wien
2 shared publications
Latest Publications
- Open Access
- 30 June 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (26)
Interband cascade devices with switchable laser and superluminescence mode
Superluminescent diodes are usually hard to fabricate and cannot switch to lasing operation. We demonstrate a practical approach for creating devices that can function as a laser as well as a superluminescent diode. The operation mode is controlled by a distinct contact that enables electrical switching between those modes. For the demonstration of this principle, we fabricated devices based on interband cascade gain media. The devices showed superluminescent power of up to 200 μW. The electrically switchable operation combines the good alignment capabilities of a laser with the broadband, low coherence properties of a superluminescent diode.
- 30 June 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (26)
Open AccessInterband cascade devices with switchable laser and superluminescence mode
Superluminescent diodes are usually hard to fabricate and cannot switch to lasing operation. We demonstrate a practical approach for creating devices that can function as a laser as well as a superluminescent diode. The operation mode is controlled by a distinct contact that enables electrical switching between those modes. For the demonstration of this principle, we fabricated devices based on interband cascade gain media. The devices showed superluminescent power of up to 200 μW. The electrically switchable operation combines the good alignment capabilities of a laser with the broadband, low coherence properties of a superluminescent diode.
- Open Access
- 9 December 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (24)
Direct measurement of current-dependent optical losses in interband cascade lasers
Interband cascade lasers (ICLs) are becoming increasingly valuable in mid-infrared applications due to their low power consumption and compatibility with silicon photonic integration, particularly for trace gas sensing. ICLs have demonstrated room-temperature continuous-wave operation in the 3–6 μm range, with excellent performance around 3.3 μm. A key factor limiting ICL performance at longer wavelengths is optical loss, i.e., caused by the intervalence band transitions. These losses increase with hole concentration in the active region, leading to a pronounced current-dependence of the optical losses in ICLs. Conventional methods that infer optical losses from length-dependent variations in parameters such as slope efficiency or threshold current require the assumption of constant optical loss. In this study, we present a direct optical transmission measurement technique to determine waveguide losses. Our experiments confirm strongly increasing waveguide losses with current density, directly impacting the quantum efficiency of ICLs. This approach offers a precise evaluation of optical losses and bears a functional alternative compared to traditional methods, addressing the limitations of assuming constant losses and providing enhanced insight into ICL performance across various wavelengths.
- 9 December 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (24)
Open AccessDirect measurement of current-dependent optical losses in interband cascade lasers
Interband cascade lasers (ICLs) are becoming increasingly valuable in mid-infrared applications due to their low power consumption and compatibility with silicon photonic integration, particularly for trace gas sensing. ICLs have demonstrated room-temperature continuous-wave operation in the 3–6 μm range, with excellent performance around 3.3 μm. A key factor limiting ICL performance at longer wavelengths is optical loss, i.e., caused by the intervalence band transitions. These losses increase with hole concentration in the active region, leading to a pronounced current-dependence of the optical losses in ICLs. Conventional methods that infer optical losses from length-dependent variations in parameters such as slope efficiency or threshold current require the assumption of constant optical loss. In this study, we present a direct optical transmission measurement technique to determine waveguide losses. Our experiments confirm strongly increasing waveguide losses with current density, directly impacting the quantum efficiency of ICLs. This approach offers a precise evaluation of optical losses and bears a functional alternative compared to traditional methods, addressing the limitations of assuming constant losses and providing enhanced insight into ICL performance across various wavelengths.
- Open Access
- 28 November 2024
- Published by Elsevier in Optics & Laser Technology
- Vol. 182
Hot-cavity linewidth enhancement factor of a quantum cascade laser
- 28 November 2024
- Published by Elsevier in Optics & Laser Technology
- Vol. 182
Open AccessHot-cavity linewidth enhancement factor of a quantum cascade laser
- Open Access
- 4 November 2024
- Published by Wiley in Laser & Photonics Reviews
- Vol. 19 (4)
Fast Gain Dynamics in Interband Cascade Lasers
Interband Cascade Lasers (ICL) have matured into a versatile technological platform in the mid‐infrared spectral domain. To broaden their applicability even further, ongoing research pursues the emission of ultrashort pulses. The most promising approach is passive mode‐locking with a fast saturable absorber. However, despite vast attempts no passive mode‐locked ICL has been demonstrated up to date. In this study, pump‐probe measurements are conducted on the ICL gain, demonstrating that 60–70% of its dynamic behavior is characterized by a rapid recovery time of 2 ps. The findings explain why passive mode‐locking of ICLs has not succeeded so far, shedding a new light on ICL dynamics as strategies are proposed to overcome the current limitations.
- 4 November 2024
- Published by Wiley in Laser & Photonics Reviews
- Vol. 19 (4)
Open AccessFast Gain Dynamics in Interband Cascade Lasers
Interband Cascade Lasers (ICL) have matured into a versatile technological platform in the mid‐infrared spectral domain. To broaden their applicability even further, ongoing research pursues the emission of ultrashort pulses. The most promising approach is passive mode‐locking with a fast saturable absorber. However, despite vast attempts no passive mode‐locked ICL has been demonstrated up to date. In this study, pump‐probe measurements are conducted on the ICL gain, demonstrating that 60–70% of its dynamic behavior is characterized by a rapid recovery time of 2 ps. The findings explain why passive mode‐locking of ICLs has not succeeded so far, shedding a new light on ICL dynamics as strategies are proposed to overcome the current limitations.
- Open Access
- 8 October 2024
- Published by Wiley in Laser & Photonics Reviews
- Vol. 19 (3)
Charge Transport in Interband Cascade Lasers: An Ab‐Initio Self‐Consistent Model
Interband cascade lasers (ICLs) stand out due to their low threshold current and minimal power consumption, rendering them viable sources for compact and mobile devices in the mid‐infrared. Since their first demonstration, they experienced major performance improvements. Mostly they originate from either improved material quality or the outcomes of numerical analysis of secluded parts. Encouraged by the impact of secluded models, an ICL‐specific simulation tool can lead to performance breakthroughs and a better comprehension of governing mechanisms. Drawing from an evaluation of existing tools designed for quantum cascade structures, a self‐consistent density matrix rate equation model is implemented to simulate the transport in both conduction and valence band heterostructures. Albeit the extensive inclusion of the quantum effects, special care was taken to maintain a high numerical efficiency. The charge transport model additionally considers optical field calculations, allowing for predictive calculations of light–current–voltage curves. The model is benchmarked against well‐established ICL designs and demonstrate reliable performance predictability. Additionally, detailed insights into device characteristics extracted from the model are provided. This ultimately allows to deepen the understanding of ICL and not only refine existing ones but also generate novel optimized designs.
- 8 October 2024
- Published by Wiley in Laser & Photonics Reviews
- Vol. 19 (3)
Open AccessCharge Transport in Interband Cascade Lasers: An Ab‐Initio Self‐Consistent Model
Interband cascade lasers (ICLs) stand out due to their low threshold current and minimal power consumption, rendering them viable sources for compact and mobile devices in the mid‐infrared. Since their first demonstration, they experienced major performance improvements. Mostly they originate from either improved material quality or the outcomes of numerical analysis of secluded parts. Encouraged by the impact of secluded models, an ICL‐specific simulation tool can lead to performance breakthroughs and a better comprehension of governing mechanisms. Drawing from an evaluation of existing tools designed for quantum cascade structures, a self‐consistent density matrix rate equation model is implemented to simulate the transport in both conduction and valence band heterostructures. Albeit the extensive inclusion of the quantum effects, special care was taken to maintain a high numerical efficiency. The charge transport model additionally considers optical field calculations, allowing for predictive calculations of light–current–voltage curves. The model is benchmarked against well‐established ICL designs and demonstrate reliable performance predictability. Additionally, detailed insights into device characteristics extracted from the model are provided. This ultimately allows to deepen the understanding of ICL and not only refine existing ones but also generate novel optimized designs.
- Open Access
- 18 January 2024
- Published by Wiley in Nanophotonics
- Vol. 13 (10) , 1773-1780
Design and performance of GaSb‐based quantum cascade detectors
InAs/AlSb quantum cascade detectors (QCDs) grown strain‐balanced on GaSb substrates are presented. This material system offers intrinsic performance‐improving properties, like a low effective electron mass of the well material of 0.026 m 0 , enhancing the optical transition strength, and a high conduction band offset of 2.28 eV, reducing the noise and allowing for high optical transition energies. InAs and AlSb strain balance each other on GaSb with an InAs:AlSb ratio of 0.96:1. To regain the freedom of a lattice‐matched material system regarding the optimization of a QCD design, submonolayer InSb layers are introduced. With strain engineering, four different active regions between 3.65 and 5.5 µm were designed with InAs:AlSb thickness ratios of up to 2.8:1, and subsequently grown and characterized. This includes an optimized QCD design at 4.3 µm, with a room‐temperature peak responsivity of 26.12 mA/W and a detectivity of 1.41 × 10 8 Jones. Additionally, all QCD designs exhibit higher‐energy interband signals in the mid‐ to near‐infrared, stemming from the InAs/AlSb type‐II alignment and the narrow InAs band gap.
- 18 January 2024
- Published by Wiley in Nanophotonics
- Vol. 13 (10) , 1773-1780
Open AccessDesign and performance of GaSb‐based quantum cascade detectors
InAs/AlSb quantum cascade detectors (QCDs) grown strain‐balanced on GaSb substrates are presented. This material system offers intrinsic performance‐improving properties, like a low effective electron mass of the well material of 0.026 m 0 , enhancing the optical transition strength, and a high conduction band offset of 2.28 eV, reducing the noise and allowing for high optical transition energies. InAs and AlSb strain balance each other on GaSb with an InAs:AlSb ratio of 0.96:1. To regain the freedom of a lattice‐matched material system regarding the optimization of a QCD design, submonolayer InSb layers are introduced. With strain engineering, four different active regions between 3.65 and 5.5 µm were designed with InAs:AlSb thickness ratios of up to 2.8:1, and subsequently grown and characterized. This includes an optimized QCD design at 4.3 µm, with a room‐temperature peak responsivity of 26.12 mA/W and a detectivity of 1.41 × 10 8 Jones. Additionally, all QCD designs exhibit higher‐energy interband signals in the mid‐ to near‐infrared, stemming from the InAs/AlSb type‐II alignment and the narrow InAs band gap.
- Open Access
3D-Printed Detector Band for Magnetic Off-Plane Flux Measurements in Laminated Machine Cores
Laminated soft magnetic cores of transformers, rotating machines etc. may exhibit complex 3D flux distributions with pronounced normal fluxes (off-plane fluxes), perpendicular to the plane of magnetization. As recent research activities have shown, detections of off-plane fluxes tend to be essential for the optimization of core performances aiming at a reduction of core losses and of audible noise. Conventional sensors for off-plane flux measurements tend to be either of high thickness, influencing the measured fluxes significantly, or require laborious preparations. In the current work, thin novel detector bands for effective and simple off-plane flux detections in laminated machine cores were manufactured. They are printed in an automatic way by an in-house developed 3D/2D assembler. The latter enables a unique combination of conductive and non-conductive materials. The detector bands were effectively tested in the interior of a two-package, three-phase model transformer core. They proved to be mechanically resilient, even for strong clamping of the core.
Open Access3D-Printed Detector Band for Magnetic Off-Plane Flux Measurements in Laminated Machine Cores
Laminated soft magnetic cores of transformers, rotating machines etc. may exhibit complex 3D flux distributions with pronounced normal fluxes (off-plane fluxes), perpendicular to the plane of magnetization. As recent research activities have shown, detections of off-plane fluxes tend to be essential for the optimization of core performances aiming at a reduction of core losses and of audible noise. Conventional sensors for off-plane flux measurements tend to be either of high thickness, influencing the measured fluxes significantly, or require laborious preparations. In the current work, thin novel detector bands for effective and simple off-plane flux detections in laminated machine cores were manufactured. They are printed in an automatic way by an in-house developed 3D/2D assembler. The latter enables a unique combination of conductive and non-conductive materials. The detector bands were effectively tested in the interior of a two-package, three-phase model transformer core. They proved to be mechanically resilient, even for strong clamping of the core.