Guido Willers
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Guido Willers has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Klemens Ilse
Fraunhofer Center for Silicon Photovoltaics (CSP) Halle (Saale) Germany
4 shared publications - Ralph Gottschalg
Fraunhofer CSP Halle (Saale) Germany
3 shared publications - Volker Naumann
Fraunhofer Center for Silicon Photovoltaics, Halle, Germany
3 shared publications Ahmed Abuelseoud
1 shared publication- Hussam Qasem
National Center for Renewable Energy, King Abdulaziz City for Science and Technology (KACST), Riyadh 11442, Saudi Arabia
1 shared publication Katja Lange
1 shared publication
Latest Publications
- Open Access
- 24 September 2025
- Published by Elsevier in Solar Energy
- Vol. 302
Impact of heated PV modules on soiling behavior and energy yield
- 24 September 2025
- Published by Elsevier in Solar Energy
- Vol. 302
Open AccessImpact of heated PV modules on soiling behavior and energy yield
- Open Access
- 26 May 2025
- Published by Wiley in Progress in Photovoltaics: Research and Applications
Impact of Different Types of Dust on Solar Glass Transmittance and PV Module Performance
The accumulation of dust on photovoltaic modules in arid and semiarid regions results in significant energy losses. However, evaluating these losses in different locations is complex, time‐consuming, and expensive. To address this challenge, our study collected dust samples from various sites and conducted soiling experiments in the laboratory using standardized methods. The investigation correlated the transmittance loss (Tloss), short‐circuit current loss (Iscloss), and dust density with the surface coverage. As a result of this analysis, a direct and precise comparison of the individual soiling losses is possible based on the gradient of the correlation lines. Additional characterization of the dust enables an exact allocation of the soiling losses to the chemical composition, optical properties, water content, and particle size. Our study used dust samples from Morocco, Qatar, and two from Thailand. The data analysis indicates that three dusts exhibit a comparable slope in soiling loss relative to surface coverage. However, one dust from Thailand has a significantly higher slope of 12.8% in transmittance loss. A comparative evaluation of the Iscloss reveals an identical ranking. A root cause analysis identified the differences in the soiling behavior through detailed dust characterization. In addition, the calculated Iscloss based on the transmission measurements showed a discrepancy between measured and calculated Iscloss. The deviation is quantified, and possible causes are described. The newly evaluated evidence of the different correlation slopes between the measurement methods not only contributes significantly to our understanding of the effects of dust on photovoltaic systems but also has practical implications. These findings will guide further development and refinement of mathematical models, potentially optimizing the efficiency and performance of photovoltaic systems in arid and semiarid regions.
- 26 May 2025
- Published by Wiley in Progress in Photovoltaics: Research and Applications
Open AccessImpact of Different Types of Dust on Solar Glass Transmittance and PV Module Performance
The accumulation of dust on photovoltaic modules in arid and semiarid regions results in significant energy losses. However, evaluating these losses in different locations is complex, time‐consuming, and expensive. To address this challenge, our study collected dust samples from various sites and conducted soiling experiments in the laboratory using standardized methods. The investigation correlated the transmittance loss (Tloss), short‐circuit current loss (Iscloss), and dust density with the surface coverage. As a result of this analysis, a direct and precise comparison of the individual soiling losses is possible based on the gradient of the correlation lines. Additional characterization of the dust enables an exact allocation of the soiling losses to the chemical composition, optical properties, water content, and particle size. Our study used dust samples from Morocco, Qatar, and two from Thailand. The data analysis indicates that three dusts exhibit a comparable slope in soiling loss relative to surface coverage. However, one dust from Thailand has a significantly higher slope of 12.8% in transmittance loss. A comparative evaluation of the Iscloss reveals an identical ranking. A root cause analysis identified the differences in the soiling behavior through detailed dust characterization. In addition, the calculated Iscloss based on the transmission measurements showed a discrepancy between measured and calculated Iscloss. The deviation is quantified, and possible causes are described. The newly evaluated evidence of the different correlation slopes between the measurement methods not only contributes significantly to our understanding of the effects of dust on photovoltaic systems but also has practical implications. These findings will guide further development and refinement of mathematical models, potentially optimizing the efficiency and performance of photovoltaic systems in arid and semiarid regions.
- Open Access
- 22 February 2024
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 269
Correlation between laboratory and outdoor soiling experiments with anti-soiling coatings
- 22 February 2024
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 269
Open AccessCorrelation between laboratory and outdoor soiling experiments with anti-soiling coatings
- 18 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 14 (2) , 330-336
Analysis of Threshold Conditions for Cementation of Soiling on PV Modules and Telescope Mirrors
To enhance the understanding of the high adhesion of dust particles on photovoltaic modules and telescope mirrors, glass, and mirror samples were subjected to soiling tests in laboratory and field experiments. The specific objective of this study was to investigate glass contamination on a microstructural level using light and scanning electron microscopy (SEM). In addition, the dusts were analyzed for their main mineral components using X-ray diffraction. The study exposed samples to natural dust from Qatar, Chile, Morocco, and the standard Middle East Test Dust. The tests showed that the adhesive strength increases abruptly due to cementation when the surface temperature falls below a critical temperature difference to the dew point (ΔT dp/critical / K). This work found values of ΔT dp/critical from 1.9 K to >7 K. The analysis shows that cementation is initiated by precipitation of the main soluble component available and promoted by surface humidity. The contribution of the water solubility of the dust components to the cementation process is more significant than the hygroscopic properties of the dust. SEM images show different cementation structures on the sample surfaces. These structures range from needle-shaped deposits <1 μm to rod- and plate-shaped structures from 3 μm to 30 μm to cubes with edge lengths from 2 μm to 50 μm. All appearances of cementation lead to significantly increased particle adhesion so that wind speeds less than 10 m/s do not remove particles from the surface. This investigation compared, at a microstructural level, laboratory test samples with outdoor samples from Morocco, Qatar, and Chile. The findings showed that the laboratory tests are very well suited to reproduce the cementation effects from the outdoor tests. This article quantified cementation conditions for the first time in dependent on operating environments. These results will support the development of suitable prevention strategies against soiling on functional surfaces.
- 18 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 14 (2) , 330-336
Analysis of Threshold Conditions for Cementation of Soiling on PV Modules and Telescope Mirrors
To enhance the understanding of the high adhesion of dust particles on photovoltaic modules and telescope mirrors, glass, and mirror samples were subjected to soiling tests in laboratory and field experiments. The specific objective of this study was to investigate glass contamination on a microstructural level using light and scanning electron microscopy (SEM). In addition, the dusts were analyzed for their main mineral components using X-ray diffraction. The study exposed samples to natural dust from Qatar, Chile, Morocco, and the standard Middle East Test Dust. The tests showed that the adhesive strength increases abruptly due to cementation when the surface temperature falls below a critical temperature difference to the dew point (ΔT dp/critical / K). This work found values of ΔT dp/critical from 1.9 K to >7 K. The analysis shows that cementation is initiated by precipitation of the main soluble component available and promoted by surface humidity. The contribution of the water solubility of the dust components to the cementation process is more significant than the hygroscopic properties of the dust. SEM images show different cementation structures on the sample surfaces. These structures range from needle-shaped deposits <1 μm to rod- and plate-shaped structures from 3 μm to 30 μm to cubes with edge lengths from 2 μm to 50 μm. All appearances of cementation lead to significantly increased particle adhesion so that wind speeds less than 10 m/s do not remove particles from the surface. This investigation compared, at a microstructural level, laboratory test samples with outdoor samples from Morocco, Qatar, and Chile. The findings showed that the laboratory tests are very well suited to reproduce the cementation effects from the outdoor tests. This article quantified cementation conditions for the first time in dependent on operating environments. These results will support the development of suitable prevention strategies against soiling on functional surfaces.