Alaeddine Zereg
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Alaeddine Zereg has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Nadhir Lebaal
ICB UMR 6303, CNRS, Université Bourgogne Franche-Comté, UTBM, Belfort, France
5 shared publications - Mohamed Taher Bouzaher
Scientific and Technical Research Centre for Arid Areas (CRSTRA), Biskra, Algeria
3 shared publications - Mounir Aksas
LEREESI Laboratory, HNS-RE2SD, Batna 05078, Algeria
3 shared publications - Abdallah Mohammedi
Laboratory of Advanced Materials Technology, Ecole Nationale Polytechnique de Constantine, Nouvelle Ville RP, B.P. Box 75, Constantine 25000, Algeria
1 shared publication - Adel Chine
LEREESI Laboratory, HNS-RE2SD, Batna 05078, Algeria
1 shared publication - Charaf-Eddine Bensaci
Laboratory of Fundamental and Applied Sciences (LSFA), Ecole Nationale Polytechnique (ENP), Algiers, Algeria
1 shared publication
Latest Publications
- Open Access
Enhancement of PEMFC Performance Using Symmetric V-Tapered Flow Channels
This study presents an optimized symmetric V-tapered cross-section (SVTC) flow-field geometry for a single-channel Proton Exchange Membrane Fuel Cell (PEMFC). Its performance is evaluated through three-dimensional Computational Fluid Dynamics (CFD) simulations conducted using ANSYS FLUENT 18.1. The SVTC architecture incorporates angled sidewalls that progressively taper the channel width, aiming to accelerate mass diffusion and increase reactant effectiveness in the cell. Performance metrics including current density, pressure drop, and net power output were analyzed across six SVTC configurations with varying taper ratios. Comparative evaluation with a conventional rectangular channel indicates that the SVTC design enhances the hydrogen and oxygen distribution, improves water management, and reduces mass transport losses. Specifically, the R5 configuration exhibited the most favorable results, achieving a peak net power density of 0.297031 W/cm2 while reducing the pressure drop by approximately 21% relative to the R1 configuration. Furthermore, the SVTC configuration enhance both current density and power density, demonstrating its effectiveness in improving mass transport and overall cell performance. The design also demonstrated improved reactant distribution uniformity and operational stability across varying load conditions. These findings underscore the critical role of channel geometry in PEMFC performance and highlight the potential of SVTC designs to enable more efficient and scalable fuel cell systems through targeted geometric optimization.
Open AccessEnhancement of PEMFC Performance Using Symmetric V-Tapered Flow Channels
This study presents an optimized symmetric V-tapered cross-section (SVTC) flow-field geometry for a single-channel Proton Exchange Membrane Fuel Cell (PEMFC). Its performance is evaluated through three-dimensional Computational Fluid Dynamics (CFD) simulations conducted using ANSYS FLUENT 18.1. The SVTC architecture incorporates angled sidewalls that progressively taper the channel width, aiming to accelerate mass diffusion and increase reactant effectiveness in the cell. Performance metrics including current density, pressure drop, and net power output were analyzed across six SVTC configurations with varying taper ratios. Comparative evaluation with a conventional rectangular channel indicates that the SVTC design enhances the hydrogen and oxygen distribution, improves water management, and reduces mass transport losses. Specifically, the R5 configuration exhibited the most favorable results, achieving a peak net power density of 0.297031 W/cm2 while reducing the pressure drop by approximately 21% relative to the R1 configuration. Furthermore, the SVTC configuration enhance both current density and power density, demonstrating its effectiveness in improving mass transport and overall cell performance. The design also demonstrated improved reactant distribution uniformity and operational stability across varying load conditions. These findings underscore the critical role of channel geometry in PEMFC performance and highlight the potential of SVTC designs to enable more efficient and scalable fuel cell systems through targeted geometric optimization.
- Open Access
- 26 May 2025
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 631, 02001
Lattice Structure Optimization Targeting to Enhance the Thermal Performance of An Injection Mold
The thermal performance of injection molds is critical for achieving high manufacturing efficiency and product quality. This study explores the optimization of lattice structures to enhance heat transfer and cooling effectiveness in injection molds. Two lattice configurations aligned and offset were investigated using computational fluid dynamics in COMSOL Multiphysics, with a focus on evaluating both heat flux and pressure drop characteristics. The offset configuration, which demonstrated approximately 12% higher heat flux while maintaining an acceptable pressure drop, was identified as the optimal design for superior heat dissipation. An optimization framework, integrating design of experiments and surrogate modeling, was employed to determine the lattice parameters that maximize thermal performance while preserving structural stability. These findings underscore the potential of the offset lattice configuration to reduce cycle times and improve product quality, thereby advancing more efficient and sustainable injection molding practices.
- 26 May 2025
- Published by EDP Sciences in E3S Web of Conferences
- Vol. 631, 02001
Open AccessLattice Structure Optimization Targeting to Enhance the Thermal Performance of An Injection Mold
The thermal performance of injection molds is critical for achieving high manufacturing efficiency and product quality. This study explores the optimization of lattice structures to enhance heat transfer and cooling effectiveness in injection molds. Two lattice configurations aligned and offset were investigated using computational fluid dynamics in COMSOL Multiphysics, with a focus on evaluating both heat flux and pressure drop characteristics. The offset configuration, which demonstrated approximately 12% higher heat flux while maintaining an acceptable pressure drop, was identified as the optimal design for superior heat dissipation. An optimization framework, integrating design of experiments and surrogate modeling, was employed to determine the lattice parameters that maximize thermal performance while preserving structural stability. These findings underscore the potential of the offset lattice configuration to reduce cycle times and improve product quality, thereby advancing more efficient and sustainable injection molding practices.
- Open Access
Effect of Deformable Gurney Flaps on the Output Power of Flapping Turbine
The Gurney flap (GF) is a simple flat plate frequently mounted at the airfoil rear. Several investigations have been devoted to studying the effect of a rigid or even movable GF on the aerodynamic behavior of several devices such as flapping airfoils and vertical or horizontal axis turbines. The present paper proposes a new concept of a deformable Gurney flap (DGF) to improve the output power of a flapping airfoil in vertical mode. The advantage of this model is the full control of the effect on the GF during the flapping movement. The DGF is expandable and contractible which allows for monitoring and adjusting the pressure distribution at the appropriate time and position. By using a 2D transient simulation with a specific dynamic mesh design, an extended numerical analysis has been provided. It was found that this model is able to increase the output power by 19.5%. Furthermore, the concept of the DGF is applied on flapping turbines in hybrid modes such as swing arm mode and D-shaped mode. These modes are investigated to clarify the studied model’s advantage and to demonstrate the possibility of applying this strategy to control the different flapping movements.
Open AccessEffect of Deformable Gurney Flaps on the Output Power of Flapping Turbine
The Gurney flap (GF) is a simple flat plate frequently mounted at the airfoil rear. Several investigations have been devoted to studying the effect of a rigid or even movable GF on the aerodynamic behavior of several devices such as flapping airfoils and vertical or horizontal axis turbines. The present paper proposes a new concept of a deformable Gurney flap (DGF) to improve the output power of a flapping airfoil in vertical mode. The advantage of this model is the full control of the effect on the GF during the flapping movement. The DGF is expandable and contractible which allows for monitoring and adjusting the pressure distribution at the appropriate time and position. By using a 2D transient simulation with a specific dynamic mesh design, an extended numerical analysis has been provided. It was found that this model is able to increase the output power by 19.5%. Furthermore, the concept of the DGF is applied on flapping turbines in hybrid modes such as swing arm mode and D-shaped mode. These modes are investigated to clarify the studied model’s advantage and to demonstrate the possibility of applying this strategy to control the different flapping movements.
- 18 December 2024
- Published by Wiley in Energy Storage
- Vol. 6 (8)
Heat Transfer Optimization of a Metal Hydride Tank Targeted to Improve Hydrogen Storage Performance
In this study, the optimization of heat transfer in a metal hydride hydrogen tank to maximize hydrogen storage was investigated. A finite element model of a quarter tank was developed in COMSOL Multiphysics with parameterized geometry. The main objectives were to maximize stored hydrogen mass and minimize tank filling time while maintaining temperature uniformity within the tank. A design of experiments (DOE) approach was used with key geometrical parameters. Compared to the base case, the hydrogen stored mass increased from 0.26 to 0.46 kg, and the tank filling time reduced from over 1100 to 450 s. The optimal design (Design point 15) resulted in an absorbed hydrogen mass of 0.4624 kg, with a charging time of 450 s, showing the most balanced performance in terms of maximizing storage while minimizing filling time and better heat dissipation. This demonstrates the potential of optimizing heat transfer to significantly improve metal hydride hydrogen storage performance. The model can be further improved by exploring different cooling designs and materials.
- 18 December 2024
- Published by Wiley in Energy Storage
- Vol. 6 (8)
Heat Transfer Optimization of a Metal Hydride Tank Targeted to Improve Hydrogen Storage Performance
In this study, the optimization of heat transfer in a metal hydride hydrogen tank to maximize hydrogen storage was investigated. A finite element model of a quarter tank was developed in COMSOL Multiphysics with parameterized geometry. The main objectives were to maximize stored hydrogen mass and minimize tank filling time while maintaining temperature uniformity within the tank. A design of experiments (DOE) approach was used with key geometrical parameters. Compared to the base case, the hydrogen stored mass increased from 0.26 to 0.46 kg, and the tank filling time reduced from over 1100 to 450 s. The optimal design (Design point 15) resulted in an absorbed hydrogen mass of 0.4624 kg, with a charging time of 450 s, showing the most balanced performance in terms of maximizing storage while minimizing filling time and better heat dissipation. This demonstrates the potential of optimizing heat transfer to significantly improve metal hydride hydrogen storage performance. The model can be further improved by exploring different cooling designs and materials.
- Open Access
Efficiency Improvement of Darrieus Wind Turbine Using Oscillating Gurney Flap
In this work, a new model of Darrieus wind turbines with an oscillating gurney flap (OGF) is proposed. A detailed 2D computational fluid dynamics (CFD) investigation is carried out using ANSYS-Fluent 22.0 to assess the turbine performance. The OGF can alter its position between the upper and lower blade surfaces during the turbine rotation. Equations related to the combined motion are implemented through a user-defined function (UDF). The proposed model is validated where a good coincidence is achieved. The overset dynamic mesh method is used. It was found that a judicious synchronization of OGF and turbine blades creates beneficial vortex interactions, which correct the pressure distribution and lead to an overall improvement in the lift force. The magnitude of the improvement is highly dependent on the OGF length and the phase motion φ. The average torque coefficient Cm for the controlled case increased by more than 19% in comparison with the nominal case.
Open AccessEfficiency Improvement of Darrieus Wind Turbine Using Oscillating Gurney Flap
In this work, a new model of Darrieus wind turbines with an oscillating gurney flap (OGF) is proposed. A detailed 2D computational fluid dynamics (CFD) investigation is carried out using ANSYS-Fluent 22.0 to assess the turbine performance. The OGF can alter its position between the upper and lower blade surfaces during the turbine rotation. Equations related to the combined motion are implemented through a user-defined function (UDF). The proposed model is validated where a good coincidence is achieved. The overset dynamic mesh method is used. It was found that a judicious synchronization of OGF and turbine blades creates beneficial vortex interactions, which correct the pressure distribution and lead to an overall improvement in the lift force. The magnitude of the improvement is highly dependent on the OGF length and the phase motion φ. The average torque coefficient Cm for the controlled case increased by more than 19% in comparison with the nominal case.
- Open Access
- 12 April 2024
- Published by EDP Sciences in International Journal for Simulation and Multidisciplinary Design Optimization
- Vol. 15, 8
Performance enhancement of Savonius wind turbine through partially deformable blades
In this study, we employ partially deformable blades to elevate the performance of Savonius wind turbines. The Bucket is constructed with rigid components equipped with a guidance system, resulting in continuous changes in its shape during turbine rotation. As the trailing edge of the advancing blade expands, it creates an active slot, effectively correcting the Bucket’s pressure distribution and enhancing the positive torque generated by the turbine. We employ a two-dimensional (2D) numerical model, implemented using the commercial software ANSYS-Fluent 23.0, with the governing motion equation executed through a user-defined function (UDF). This investigation explores the mechanism of performance enhancement by varying expansion amplitudes Our results, obtained at a Tip-speed ratio (TSR) of 1, reveal that when the amplitude of deformation exceeds one-quarter of the Bucket radius, the partially deformable blade outperforms the rigid blade, leading to a remarkable 32% improvement in the torque coefficient. These findings signify a promising path toward enhancing Savonius turbine efficiency.
- 12 April 2024
- Published by EDP Sciences in International Journal for Simulation and Multidisciplinary Design Optimization
- Vol. 15, 8
Open AccessPerformance enhancement of Savonius wind turbine through partially deformable blades
In this study, we employ partially deformable blades to elevate the performance of Savonius wind turbines. The Bucket is constructed with rigid components equipped with a guidance system, resulting in continuous changes in its shape during turbine rotation. As the trailing edge of the advancing blade expands, it creates an active slot, effectively correcting the Bucket’s pressure distribution and enhancing the positive torque generated by the turbine. We employ a two-dimensional (2D) numerical model, implemented using the commercial software ANSYS-Fluent 23.0, with the governing motion equation executed through a user-defined function (UDF). This investigation explores the mechanism of performance enhancement by varying expansion amplitudes Our results, obtained at a Tip-speed ratio (TSR) of 1, reveal that when the amplitude of deformation exceeds one-quarter of the Bucket radius, the partially deformable blade outperforms the rigid blade, leading to a remarkable 32% improvement in the torque coefficient. These findings signify a promising path toward enhancing Savonius turbine efficiency.
- Open Access
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3059 (1) , 030015
Numerical analysis and optimization of a vertical axis wind turbine with a flapped blade
Wind energy is perceived to have significant promise as a clean and practical source of renewable energy and as a crucial component in lowering harmful carbon d
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3059 (1) , 030015
Open AccessNumerical analysis and optimization of a vertical axis wind turbine with a flapped blade
Wind energy is perceived to have significant promise as a clean and practical source of renewable energy and as a crucial component in lowering harmful carbon d