Mounir Aksas
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mounir Aksas has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Nadhir Lebaal
ICB UMR 6303, CNRS, Université Bourgogne Franche-Comté, UTBM, Belfort, France
4 shared publications - Alaeddine Zereg
Laboratoire Interdisciplinaire Carnot de Bourgogne (ICB), UMR CNRS 6303, Université Marie et Louis Pasteur, UTBM, 90010 Belfort, France
3 shared publications - Mohamed Taher Bouzaher
Scientific and Technical Research Centre for Arid Areas (CRSTRA), Biskra, Algeria
2 shared publications - Ayoub Boutaghane
LEREESI Laboratory, HNS-RE2SD, Batna 05078, Algeria
1 shared publication - Charaf-Eddine Bensaci
Laboratory of Fundamental and Applied Sciences (LSFA), Ecole Nationale Polytechnique (ENP), Algiers, Algeria
1 shared publication - Chebana Abdelbasset
Laboratory of Engineering and Science of Advanced Materials (ISMA), University Abbes Laghrour, Khenchela 40004, Algeria
1 shared publication
Latest Publications
- Open Access
Feasibility and Sensitivity Analysis of an Off-Grid PV/Wind Hybrid Energy System Integrated with Green Hydrogen Production: A Case Study of Algeria
Algeria’s transition toward sustainable energy requires the exploitation of its abundant solar and wind resources for green hydrogen production. This study assesses the techno-economic feasibility of an off-grid PV/wind hybrid system integrated with a hydrogen subsystem (electrolyzer, fuel cell, and hydrogen storage) to supply both electricity and hydrogen to decentralized sites in Algeria. Using HOMER Pro, five representative Algerian regions were analyzed, accounting for variations in solar irradiation, wind speed, and groundwater availability. A deferrable water-extraction and treatment load was incorporated to model the water requirements of the electrolyzer. In addition, a comprehensive sensitivity analysis was conducted on solar irradiation, wind speed, and the capital costs of PV panels and wind turbines to capture the effects of renewable resource and investment cost fluctuations. The results indicate significant regional variation, with the levelized cost of energy (LCOE) ranging from 0.514 to 0.868 $/kWh, the levelized cost of hydrogen (LCOH) between 8.31 and 12.4 $/kg, and the net present cost (NPC) between 10.28 M$ and 17.7 M$, demonstrating that all cost metrics are highly sensitive to these variations.Open AccessFeasibility and Sensitivity Analysis of an Off-Grid PV/Wind Hybrid Energy System Integrated with Green Hydrogen Production: A Case Study of Algeria
Algeria’s transition toward sustainable energy requires the exploitation of its abundant solar and wind resources for green hydrogen production. This study assesses the techno-economic feasibility of an off-grid PV/wind hybrid system integrated with a hydrogen subsystem (electrolyzer, fuel cell, and hydrogen storage) to supply both electricity and hydrogen to decentralized sites in Algeria. Using HOMER Pro, five representative Algerian regions were analyzed, accounting for variations in solar irradiation, wind speed, and groundwater availability. A deferrable water-extraction and treatment load was incorporated to model the water requirements of the electrolyzer. In addition, a comprehensive sensitivity analysis was conducted on solar irradiation, wind speed, and the capital costs of PV panels and wind turbines to capture the effects of renewable resource and investment cost fluctuations. The results indicate significant regional variation, with the levelized cost of energy (LCOE) ranging from 0.514 to 0.868 $/kWh, the levelized cost of hydrogen (LCOH) between 8.31 and 12.4 $/kg, and the net present cost (NPC) between 10.28 M$ and 17.7 M$, demonstrating that all cost metrics are highly sensitive to these variations. - Open Access
Effect of Deformable Gurney Flaps on the Output Power of Flapping Turbine
The Gurney flap (GF) is a simple flat plate frequently mounted at the airfoil rear. Several investigations have been devoted to studying the effect of a rigid or even movable GF on the aerodynamic behavior of several devices such as flapping airfoils and vertical or horizontal axis turbines. The present paper proposes a new concept of a deformable Gurney flap (DGF) to improve the output power of a flapping airfoil in vertical mode. The advantage of this model is the full control of the effect on the GF during the flapping movement. The DGF is expandable and contractible which allows for monitoring and adjusting the pressure distribution at the appropriate time and position. By using a 2D transient simulation with a specific dynamic mesh design, an extended numerical analysis has been provided. It was found that this model is able to increase the output power by 19.5%. Furthermore, the concept of the DGF is applied on flapping turbines in hybrid modes such as swing arm mode and D-shaped mode. These modes are investigated to clarify the studied model’s advantage and to demonstrate the possibility of applying this strategy to control the different flapping movements.
Open AccessEffect of Deformable Gurney Flaps on the Output Power of Flapping Turbine
The Gurney flap (GF) is a simple flat plate frequently mounted at the airfoil rear. Several investigations have been devoted to studying the effect of a rigid or even movable GF on the aerodynamic behavior of several devices such as flapping airfoils and vertical or horizontal axis turbines. The present paper proposes a new concept of a deformable Gurney flap (DGF) to improve the output power of a flapping airfoil in vertical mode. The advantage of this model is the full control of the effect on the GF during the flapping movement. The DGF is expandable and contractible which allows for monitoring and adjusting the pressure distribution at the appropriate time and position. By using a 2D transient simulation with a specific dynamic mesh design, an extended numerical analysis has been provided. It was found that this model is able to increase the output power by 19.5%. Furthermore, the concept of the DGF is applied on flapping turbines in hybrid modes such as swing arm mode and D-shaped mode. These modes are investigated to clarify the studied model’s advantage and to demonstrate the possibility of applying this strategy to control the different flapping movements.
- Open Access
Efficiency Improvement of Darrieus Wind Turbine Using Oscillating Gurney Flap
In this work, a new model of Darrieus wind turbines with an oscillating gurney flap (OGF) is proposed. A detailed 2D computational fluid dynamics (CFD) investigation is carried out using ANSYS-Fluent 22.0 to assess the turbine performance. The OGF can alter its position between the upper and lower blade surfaces during the turbine rotation. Equations related to the combined motion are implemented through a user-defined function (UDF). The proposed model is validated where a good coincidence is achieved. The overset dynamic mesh method is used. It was found that a judicious synchronization of OGF and turbine blades creates beneficial vortex interactions, which correct the pressure distribution and lead to an overall improvement in the lift force. The magnitude of the improvement is highly dependent on the OGF length and the phase motion φ. The average torque coefficient Cm for the controlled case increased by more than 19% in comparison with the nominal case.
Open AccessEfficiency Improvement of Darrieus Wind Turbine Using Oscillating Gurney Flap
In this work, a new model of Darrieus wind turbines with an oscillating gurney flap (OGF) is proposed. A detailed 2D computational fluid dynamics (CFD) investigation is carried out using ANSYS-Fluent 22.0 to assess the turbine performance. The OGF can alter its position between the upper and lower blade surfaces during the turbine rotation. Equations related to the combined motion are implemented through a user-defined function (UDF). The proposed model is validated where a good coincidence is achieved. The overset dynamic mesh method is used. It was found that a judicious synchronization of OGF and turbine blades creates beneficial vortex interactions, which correct the pressure distribution and lead to an overall improvement in the lift force. The magnitude of the improvement is highly dependent on the OGF length and the phase motion φ. The average torque coefficient Cm for the controlled case increased by more than 19% in comparison with the nominal case.
- Open Access
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3059 (1) , 030015
Numerical analysis and optimization of a vertical axis wind turbine with a flapped blade
Wind energy is perceived to have significant promise as a clean and practical source of renewable energy and as a crucial component in lowering harmful carbon d
- 1 January 2024
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 3059 (1) , 030015
Open AccessNumerical analysis and optimization of a vertical axis wind turbine with a flapped blade
Wind energy is perceived to have significant promise as a clean and practical source of renewable energy and as a crucial component in lowering harmful carbon d