Maria Isabella Federici
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Maria Isabella Federici has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Antonio Barone
Department of Surgical, Medical, Molecular Pathology and of the Critical Area, University of Pisa, 56126 Pisa, Italy
1 shared publication - Chiara Cinquini
Department of Surgical, Medical, Molecular Pathologies and of the Critical Needs, School of Dentistry, University of Pisa, 56126 Pisa, Italy
1 shared publication - Elisabetta Carli
Unit of Pediatric Dentistry, Department of Surgical, Medical, Molecular and Critical Area Pathology, University of Pisa, 56126 Pisa, Italy
1 shared publication - Giacomo Derchi
University of Pisa
1 shared publication - Jason Liu
Section for Orthodontics, Department of Dentistry and Oral Health, Aarhus University, Aarhus, Denmark
1 shared publication - Jennifer Christensen
Section for Oral Radiology and Endodontics, Department of Dentistry and Oral Health, Aarhus University , Aarhus 8000
1 shared publication
Latest Publications
- Open Access
- 1 January 2026
- Published by XMLink in Imaging Science in Dentistry
- Vol. 56 (1) , 36-44
Reliability of dental-dedicated magnetic resonance imaging for 2-dimensional orthodontic diagnosis: A pilot study of landmark identification
Srivastav S, et al. Imaging Sci Dent. 2025 Nov;55:e47. https://doi.org/10.5624/isd.20250201
- 1 January 2026
- Published by XMLink in Imaging Science in Dentistry
- Vol. 56 (1) , 36-44
Open AccessReliability of dental-dedicated magnetic resonance imaging for 2-dimensional orthodontic diagnosis: A pilot study of landmark identification
Srivastav S, et al. Imaging Sci Dent. 2025 Nov;55:e47. https://doi.org/10.5624/isd.20250201
- 20 February 2024
- Published by Kaunas University of Technology (KTU) in Materials Science
- Vol. 30 (1) , 114-120
Evaluation of Accuracy of Different Print Angulations for 3D Printed Dental Crowns
Additive manufacturing (AM), also known as additive printing, is increasing its importance in every field of dentistry. There are different methods of AM, one of these being digital light processing (DLP). Several factors can influence the accuracy of printed crowns, and one of them is the building or printing orientation. Therefore, the aim of this study is to evaluate the trueness and precision of temporary crowns produced via DLP with different printing angles. An artificial molar prepared to receive a full crown was scanned. A total of 15 resin crowns were printed through DLP and divided into three groups considering 3 different printing angulations: 90°, 45° or a custom angulation. Trueness and precision were evaluated considering the Root Mean Square Error (RMSE). Regarding the internal fit, the 90° printing angulation showed a higher accuracy compared to the other angulations, whereas regarding the occlusal aspect, Custom angulation crowns were better. Custom Crowns showed a higher precision when considering the internal aspect, being equal to the 90° printing angulation regarding the occlusal aspect. 135° printing angulation value performed equal or worse precision and accuracy in all zones. In terms of trueness and precision, custom angulation crowns showed acceptable internal and occlusal results for 3D printed provisional crowns.
- 20 February 2024
- Published by Kaunas University of Technology (KTU) in Materials Science
- Vol. 30 (1) , 114-120
Evaluation of Accuracy of Different Print Angulations for 3D Printed Dental Crowns
Additive manufacturing (AM), also known as additive printing, is increasing its importance in every field of dentistry. There are different methods of AM, one of these being digital light processing (DLP). Several factors can influence the accuracy of printed crowns, and one of them is the building or printing orientation. Therefore, the aim of this study is to evaluate the trueness and precision of temporary crowns produced via DLP with different printing angles. An artificial molar prepared to receive a full crown was scanned. A total of 15 resin crowns were printed through DLP and divided into three groups considering 3 different printing angulations: 90°, 45° or a custom angulation. Trueness and precision were evaluated considering the Root Mean Square Error (RMSE). Regarding the internal fit, the 90° printing angulation showed a higher accuracy compared to the other angulations, whereas regarding the occlusal aspect, Custom angulation crowns were better. Custom Crowns showed a higher precision when considering the internal aspect, being equal to the 90° printing angulation regarding the occlusal aspect. 135° printing angulation value performed equal or worse precision and accuracy in all zones. In terms of trueness and precision, custom angulation crowns showed acceptable internal and occlusal results for 3D printed provisional crowns.