Errj Sansonetti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Errj Sansonetti has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
Bruno Andersons
Latvian State Institute of Wood Chemistry, Riga, Latvia
3 shared publicationsDace Cirule
Latvian State Institute of Wood Chemistry, Riga, Latvia
3 shared publicationsEdgars Kuka
Latvian State Institute of Wood Chemistry, Riga, Latvia
3 shared publicationsIngeborga Andersone
Latvian State Institute of Wood Chemistry, Riga, Latvia
3 shared publicationsKristine Meile
Latvian State Institute of Wood Chemistry, Riga, Latvia
3 shared publicationsLaima Vevere
Latvian State Institute of Wood Chemistry, Riga, Latvia
3 shared publications
Latest Publications
- 21 July 2025
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 83 (4) , 1-8
Potentiality of microwave technology for treatment of Norway spruce wood to reduce risk of resin exudation from wood materials
- 21 July 2025
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 83 (4) , 1-8
Potentiality of microwave technology for treatment of Norway spruce wood to reduce risk of resin exudation from wood materials
- Open Access
Changes in Wood Plastic Composite Properties After Natural Weathering and Potential Microplastic Formation
Wood plastic composites (WPCs) have recently gained attention as alternatives to traditional wood materials for outdoor use, thanks to their enhanced moisture resistance and durability, which extends their service life. Discolouration as well as surface erosion has been observed during weathering for both WPCs with untreated and heat-treated wood. However, aspects such as changes in surface hydrophobicity, chemistry, and erosion in terms of microplastic formation have received less attention; this research aimed to evaluate these factors during natural weathering. Four types of WPC samples, consisting of 50% wood particles (untreated and heat-treated) and 50% polypropylene, were naturally weathered in Latvia for two years. The samples measured 240 mm × 240 mm × 5 mm. Results showed rapid colour changes, microcracks, and exposed wood particles, suggesting microplastic formation. ATR-FTIR analysis showed increased absorption at 1715 cm⁻¹ (carbonyl groups) and at 3410 cm−1 and 3460 cm−1, typical of wood, indicating chemical changes on the surface. These changes influenced surface hydrophobicity, roughness, and water penetration. In a relatively short exposure time, WPCs without proper additives undergo significant changes in their aesthetic and physical properties, leading to surface erosion and potential microplastic formation. This could challenge the perception of WPCs as environmentally friendly materials.
Open AccessChanges in Wood Plastic Composite Properties After Natural Weathering and Potential Microplastic Formation
Wood plastic composites (WPCs) have recently gained attention as alternatives to traditional wood materials for outdoor use, thanks to their enhanced moisture resistance and durability, which extends their service life. Discolouration as well as surface erosion has been observed during weathering for both WPCs with untreated and heat-treated wood. However, aspects such as changes in surface hydrophobicity, chemistry, and erosion in terms of microplastic formation have received less attention; this research aimed to evaluate these factors during natural weathering. Four types of WPC samples, consisting of 50% wood particles (untreated and heat-treated) and 50% polypropylene, were naturally weathered in Latvia for two years. The samples measured 240 mm × 240 mm × 5 mm. Results showed rapid colour changes, microcracks, and exposed wood particles, suggesting microplastic formation. ATR-FTIR analysis showed increased absorption at 1715 cm⁻¹ (carbonyl groups) and at 3410 cm−1 and 3460 cm−1, typical of wood, indicating chemical changes on the surface. These changes influenced surface hydrophobicity, roughness, and water penetration. In a relatively short exposure time, WPCs without proper additives undergo significant changes in their aesthetic and physical properties, leading to surface erosion and potential microplastic formation. This could challenge the perception of WPCs as environmentally friendly materials.
- Open Access
Enhancing the Wetting Properties of Activated Biochar by Oxidation with Hydrogen Peroxide
In order to explore the possibilities of increasing the hydrophilicity of carbon-based adsorbents, catalysts, or electrode materials in aqueous solutions, the oxidation of wood-based activated biochar using H2O2 was investigated. The properties of oxidized activated biochar obtained at different activation temperatures (600, 700, and 800 °C) and H2O2 oxidized for 15–180 min were investigated using the characteristics of surface functionality, elemental composition, porous structure, contact angle measurements, FTIR spectroscopy, and immersion calorimetry. It was observed that the optimal oxidation time was different for each sample depending on activation temperature, and the degree of oxidation can be tailored by changing the oxidation time. The course of oxidation depends on the degree of graphitization and functionalization, determined by the activation temperature. It was established that the highest degree of oxidation and increase in wettability is observed for samples with the lowest degree of activation obtained at a temperature of 600 °C.
Open AccessEnhancing the Wetting Properties of Activated Biochar by Oxidation with Hydrogen Peroxide
In order to explore the possibilities of increasing the hydrophilicity of carbon-based adsorbents, catalysts, or electrode materials in aqueous solutions, the oxidation of wood-based activated biochar using H2O2 was investigated. The properties of oxidized activated biochar obtained at different activation temperatures (600, 700, and 800 °C) and H2O2 oxidized for 15–180 min were investigated using the characteristics of surface functionality, elemental composition, porous structure, contact angle measurements, FTIR spectroscopy, and immersion calorimetry. It was observed that the optimal oxidation time was different for each sample depending on activation temperature, and the degree of oxidation can be tailored by changing the oxidation time. The course of oxidation depends on the degree of graphitization and functionalization, determined by the activation temperature. It was established that the highest degree of oxidation and increase in wettability is observed for samples with the lowest degree of activation obtained at a temperature of 600 °C.
- 3 May 2024
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 82 (5) , 1293-1300
Effect of heat treatment at mild temperatures on the composition and physico-chemical properties of Scots pine resin
- 3 May 2024
- Published by Springer Nature in European Journal of Wood and Wood Products
- Vol. 82 (5) , 1293-1300
Effect of heat treatment at mild temperatures on the composition and physico-chemical properties of Scots pine resin
- Open Access
- 31 January 2024
- Published by Springer Nature in Research Square
Effect of heat treatment at mild temperatures on the composition and physico-chemical properties of Scots pine resin
A major function of resin in trees is to provide defense against external attacks by releasing the resin flow on the attacked or damaged area. Nonetheless, the leakage of the resin on the surface can have a negative aesthetic and economic impact on wood material. The aim of this study was to investigate how heat treatment affects the chemo-physical properties of the resin of Pinus sylvestris L. in order to hinder the exudation on wood surface during service. To reduce the fluidity of the resin, it is necessary to remove the volatile fraction of resin, and several studies have been carried out in this direction, providing useful information about this process. The results from thermal analyses (DSC, TGA) confirmed that heat treatment at mild temperatures, 80 °C, 90 °C and 100 °C, respectively, had a positive effect on increasing the glass transition temperature Tg and showed a good correlation between the Tg and the residual volatile content. FTIR spectroscopy, before and after heat treatment, did not show major changes in chemical structures, whilst UHPLC-DAD-MS analysis revealed significant differences for the ratios of compounds, which are the result of possible chemical reactions, such as dehydrogenation, oxidation and isomerization.
- 31 January 2024
- Published by Springer Nature in Research Square
Open AccessEffect of heat treatment at mild temperatures on the composition and physico-chemical properties of Scots pine resin
A major function of resin in trees is to provide defense against external attacks by releasing the resin flow on the attacked or damaged area. Nonetheless, the leakage of the resin on the surface can have a negative aesthetic and economic impact on wood material. The aim of this study was to investigate how heat treatment affects the chemo-physical properties of the resin of Pinus sylvestris L. in order to hinder the exudation on wood surface during service. To reduce the fluidity of the resin, it is necessary to remove the volatile fraction of resin, and several studies have been carried out in this direction, providing useful information about this process. The results from thermal analyses (DSC, TGA) confirmed that heat treatment at mild temperatures, 80 °C, 90 °C and 100 °C, respectively, had a positive effect on increasing the glass transition temperature Tg and showed a good correlation between the Tg and the residual volatile content. FTIR spectroscopy, before and after heat treatment, did not show major changes in chemical structures, whilst UHPLC-DAD-MS analysis revealed significant differences for the ratios of compounds, which are the result of possible chemical reactions, such as dehydrogenation, oxidation and isomerization.