Bozhou Cai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bozhou Cai has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Shin-Ichi Nishizawa
Research Institute for Applied Mechanics, Kyushu University, Fukuoka, Japan
4 shared publications - Jiuyang Yuan
Kyushu University, 6-1 Kasuga-koen, Kasuga, Fukuoka 816-8580, Japan
3 shared publications - Wataru Saito
Research Institute for Applied Mechanics, Kyushu University, Fukuoka, Japan
3 shared publications Yoshiji Miyamura
Kyushu University, 6-1 Kasuga-koen, Kasuga, Fukuoka 816-8580, Japan
3 shared publications- Hiroaki Kato
Toshiba Electronic Devices & Storage Corporation, 1-1, Iwauchi-machi, Nomi, Ishikawa, 923-1293, Japan
1 shared publication Jiuyang Yuan
Kyushu University, Fukuoka, Fukuoka, Japan
1 shared publication
Latest Publications
- 1 December 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (12) , 12SP16
Study on dislocation propagation in trench structures during scaled Si-IGBTs thermal oxidation
This study investigates the stress and dislocation behavior in trench structures on the silicon chip during the silicon insulated gate bipolar transistor (Si-IGBT) thermal oxidation process. A three-dimensional finite element analysis coupled with the Haasen–Alexander–Sumino dislocation kinetics model was carried out. The results indicate that dislocation propagation during thermal oxidation is highly temperature-dependent, and dislocations primarily form at trench bottom corners due to stress concentration. Trench scaling effectively reduces overall dislocation density by lowering the oxidation temperature. Furthermore, the combination of trench scaling and semicircular trench bottom design decreases dislocation density in stress-concentrated regions, providing guidance for the structural optimization of Si-IGBTs from a defect-suppression perspective.
- 1 December 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (12) , 12SP16
Study on dislocation propagation in trench structures during scaled Si-IGBTs thermal oxidation
This study investigates the stress and dislocation behavior in trench structures on the silicon chip during the silicon insulated gate bipolar transistor (Si-IGBT) thermal oxidation process. A three-dimensional finite element analysis coupled with the Haasen–Alexander–Sumino dislocation kinetics model was carried out. The results indicate that dislocation propagation during thermal oxidation is highly temperature-dependent, and dislocations primarily form at trench bottom corners due to stress concentration. Trench scaling effectively reduces overall dislocation density by lowering the oxidation temperature. Furthermore, the combination of trench scaling and semicircular trench bottom design decreases dislocation density in stress-concentrated regions, providing guidance for the structural optimization of Si-IGBTs from a defect-suppression perspective.
- Open Access
- 26 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. PP, 1
Impact of Dislocations on Minority Carrier Lifetime in 300-mm Si Wafers During a High Thermal Budget Process
A quantitatively analysis of the impact of process induced dislocations on minority carrier lifetime in 300-mm Si wafer was presented. High thermal budget processes, such as oxidation and impurity diffusion, are essential in Insulated Gate Bipolar Transistor (IGBT) fabrication but can induce dislocations in large-diameter Si wafers. These dislocations may degrade the minority carrier lifetime, directly impairing device performance. Therefore, establishing a quantitative relationship between dislocation density and lifetime is crucial for process control and yield improvement. In this paper, we first demonstrate that dislocation propagation during thermal processes can be effectively suppressed by controlling the magnitude of a parameter “f”, which represents the dislocation propagation rate. Subsequently, wafers with varying dislocation density were fabricated through a series of consecutive thermal cycles. The dislocation density was determined by numerical calculation, while the corresponding minority carrier lifetime was measured using the micro-photoconductivity decay (l-PCD) method. A quantitative correlation between dislocation density and lifetime was established. These findings contribute to preventing dislocation-induced lifetime degradation during high thermal budget process in power device manufacturing.
- 26 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. PP, 1
Open AccessImpact of Dislocations on Minority Carrier Lifetime in 300-mm Si Wafers During a High Thermal Budget Process
A quantitatively analysis of the impact of process induced dislocations on minority carrier lifetime in 300-mm Si wafer was presented. High thermal budget processes, such as oxidation and impurity diffusion, are essential in Insulated Gate Bipolar Transistor (IGBT) fabrication but can induce dislocations in large-diameter Si wafers. These dislocations may degrade the minority carrier lifetime, directly impairing device performance. Therefore, establishing a quantitative relationship between dislocation density and lifetime is crucial for process control and yield improvement. In this paper, we first demonstrate that dislocation propagation during thermal processes can be effectively suppressed by controlling the magnitude of a parameter “f”, which represents the dislocation propagation rate. Subsequently, wafers with varying dislocation density were fabricated through a series of consecutive thermal cycles. The dislocation density was determined by numerical calculation, while the corresponding minority carrier lifetime was measured using the micro-photoconductivity decay (l-PCD) method. A quantitative correlation between dislocation density and lifetime was established. These findings contribute to preventing dislocation-induced lifetime degradation during high thermal budget process in power device manufacturing.
- 19 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 38 (2) , 263-269
A Warpage Prediction Model for Trench Field-Plate Power MOSFET in 300mm-Diameter Process
A wafer warpage prediction model for trench field-plate MOSFETs on large diameter wafers is proposed. Trench field-plate MOSFETs have deeper trenches and thicker oxides compared to conventional power MOSFETs, and the stress imbalance between the front and back of the wafer must be controlled to suppress wafer warpage in the mass-production process. Therefore, predicting wafer warpage throughout the process is a key technology from the viewpoint of process integration, and its importance is increasing with the use of large-diameter wafers. In this study, as a main process module in trench field-plate power MOSFET process, the processes of trench formation, oxidation, polysilicon deposition, and annealing were examined. The wafer warpage and Raman shift were analyzed by comparing the experiment results with simulations in a 300 mm diameter process. Based on the measured wafer warpage, anisotropic deformation of the poly silicon after annealing was suggested, and a new model considering this anisotropic deformation was developed to predict the through-process for 300 mm wafers.
- 19 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 38 (2) , 263-269
A Warpage Prediction Model for Trench Field-Plate Power MOSFET in 300mm-Diameter Process
A wafer warpage prediction model for trench field-plate MOSFETs on large diameter wafers is proposed. Trench field-plate MOSFETs have deeper trenches and thicker oxides compared to conventional power MOSFETs, and the stress imbalance between the front and back of the wafer must be controlled to suppress wafer warpage in the mass-production process. Therefore, predicting wafer warpage throughout the process is a key technology from the viewpoint of process integration, and its importance is increasing with the use of large-diameter wafers. In this study, as a main process module in trench field-plate power MOSFET process, the processes of trench formation, oxidation, polysilicon deposition, and annealing were examined. The wafer warpage and Raman shift were analyzed by comparing the experiment results with simulations in a 300 mm diameter process. Based on the measured wafer warpage, anisotropic deformation of the poly silicon after annealing was suggested, and a new model considering this anisotropic deformation was developed to predict the through-process for 300 mm wafers.
- Open Access
- 14 February 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (3) , 03SP16
Study on stress in trench structures during silicon IGBTs process-oxidation
In silicon insulated gate bipolar transistors, the trench gate structure is used to achieve smaller cell size and lower ON resistance, and thereby reduces energy loss. However, the thermal process can cause large stress near the trench and sometimes degrades device performance. This study proposed a three-dimensional model of a silicon chip with trench structures to analyze the stress distribution induced by thermal process around the trench, the scribe line, and the bottom surface of the chip. The calculated stress is in good agreement with measurement by Raman spectroscopy. The mesa top has much higher stress than the scribe line and the bottom surface. The stress depends on oxide thickness and the size scaling may reduce the stress.
- 14 February 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63 (3) , 03SP16
Open AccessStudy on stress in trench structures during silicon IGBTs process-oxidation
In silicon insulated gate bipolar transistors, the trench gate structure is used to achieve smaller cell size and lower ON resistance, and thereby reduces energy loss. However, the thermal process can cause large stress near the trench and sometimes degrades device performance. This study proposed a three-dimensional model of a silicon chip with trench structures to analyze the stress distribution induced by thermal process around the trench, the scribe line, and the bottom surface of the chip. The calculated stress is in good agreement with measurement by Raman spectroscopy. The mesa top has much higher stress than the scribe line and the bottom surface. The stress depends on oxide thickness and the size scaling may reduce the stress.