Shin-Ichi Nishizawa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Shin-Ichi Nishizawa has a total of 73 co-authors. Here are the top co-authors by number of shared publications:
- Wataru Saito
Research Institute for Applied Mechanics, Kyushu University, Fukuoka, Japan
26 shared publications - Bozhou Cai
Kyushu University, 6-1 Kasuga-koen, Kasuga, Fukuoka 816-8580, Japan
4 shared publications Yoshiji Miyamura
Kyushu University 3 , 6-1 Kasuga-koen, Kasuga, Fukuoka 816-8580
4 shared publications- Jiuyang Yuan
Kyushu University, 6-1 Kasuga-koen, Kasuga, Fukuoka 816-8580, Japan
3 shared publications - Katsuhiro Hata
Institute of Industrial Science, The University of Tokyo, Tokyo, Japan
3 shared publications - Keiji Wada
Tokyo Metropolitan University
3 shared publications
Latest Publications
- Open Access
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 393, 79-86
Numerical Simulation of Optimal Source Temperature Distribution in PVT Method for SiC Single Crystals
In bulk SiC crystal growth using the PVT method, recrystallization within the source material leads to a decrease in growth rate and source utilization. In this study, numerical simulations were used to investigate the source temperature distribution and its effect on the growth rate and source utilization. Recrystallization in the upper and lower regions was considered separately. The results showed that reducing the source temperature gradient prevents recrystallization in the upper region, and a unidirectional gradient prevents recrystallization in the lower region, leading to higher growth rates and source utilization.
- 18 May 2026
- Published by Trans Tech Publications, Ltd. in Solid State Phenomena
- Vol. 393, 79-86
Open AccessNumerical Simulation of Optimal Source Temperature Distribution in PVT Method for SiC Single Crystals
In bulk SiC crystal growth using the PVT method, recrystallization within the source material leads to a decrease in growth rate and source utilization. In this study, numerical simulations were used to investigate the source temperature distribution and its effect on the growth rate and source utilization. Recrystallization in the upper and lower regions was considered separately. The results showed that reducing the source temperature gradient prevents recrystallization in the upper region, and a unidirectional gradient prevents recrystallization in the lower region, leading to higher growth rates and source utilization.
- 4 May 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (18)
Quantitative analysis of Sb donors in Si by photoluminescence due to bound exciton two-electron transition
Bound exciton (BE) emission line from Sb donors in Si coincides spectrally with that from P donors, preventing their separation by conventional photoluminescence (PL) spectroscopy. In contrast, the energies of bound exciton two-electron (BE2e) transitions in which the final state is an excited impurity are strongly impurity dependent and allow clear discrimination. We demonstrate quantitative determination of Sb donors in Si using the intensity ratio of the BE2e transition to free exciton emission. Sb concentrations from 1 × 1012 to 5 × 1015 cm−3 are measured without interference from P donors, establishing BE2e PL as a practical method for Sb quantification.
- 4 May 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 128 (18)
Quantitative analysis of Sb donors in Si by photoluminescence due to bound exciton two-electron transition
Bound exciton (BE) emission line from Sb donors in Si coincides spectrally with that from P donors, preventing their separation by conventional photoluminescence (PL) spectroscopy. In contrast, the energies of bound exciton two-electron (BE2e) transitions in which the final state is an excited impurity are strongly impurity dependent and allow clear discrimination. We demonstrate quantitative determination of Sb donors in Si using the intensity ratio of the BE2e transition to free exciton emission. Sb concentrations from 1 × 1012 to 5 × 1015 cm−3 are measured without interference from P donors, establishing BE2e PL as a practical method for Sb quantification.
- Open Access
- 26 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 7, 907-927
Detection of Wire Lift-Off in Si-IGBTs and SiC-MOSFETs Using Machine Learning on Switching Waveforms
Power cycling degradation in power modules is one of the most common failure modes in power electronic systems. This study presents a method to detect wire lift-off using machine learning analysis of switching waveforms of gate voltage and emitter/source current in Si-IGBT and SiC-MOSFET power modules. Five key aspects are investigated as follows: (1) evaluation of different detection signals and their combinations, (2) segment-wise analysis to identify waveform regions that contribute most to classification, (3) impact of waveform sampling rate on detection accuracy, (4) validation using mixed datasets from multiple modules, and (5) comparison between Si-IGBT and SiC-MOSFET devices. The turn-off gate voltage waveforms provide the highest accuracy, and a high accuracy of about 99 % was achieved even with downsampling from 2.5 GS/s to 100 MS/s. The mixed datasets show no degradation in accuracy, and the optimum gate drive condition for high accuracy differs between Si-IGBTs and SiC-MOSFETs. Overall, the proposed method achieves over 99 % classification accuracy, demonstrating its potential for reliable and low-cost monitoring of power device degradation.
- 26 February 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Power Electronics
- Vol. 7, 907-927
Open AccessDetection of Wire Lift-Off in Si-IGBTs and SiC-MOSFETs Using Machine Learning on Switching Waveforms
Power cycling degradation in power modules is one of the most common failure modes in power electronic systems. This study presents a method to detect wire lift-off using machine learning analysis of switching waveforms of gate voltage and emitter/source current in Si-IGBT and SiC-MOSFET power modules. Five key aspects are investigated as follows: (1) evaluation of different detection signals and their combinations, (2) segment-wise analysis to identify waveform regions that contribute most to classification, (3) impact of waveform sampling rate on detection accuracy, (4) validation using mixed datasets from multiple modules, and (5) comparison between Si-IGBT and SiC-MOSFET devices. The turn-off gate voltage waveforms provide the highest accuracy, and a high accuracy of about 99 % was achieved even with downsampling from 2.5 GS/s to 100 MS/s. The mixed datasets show no degradation in accuracy, and the optimum gate drive condition for high accuracy differs between Si-IGBTs and SiC-MOSFETs. Overall, the proposed method achieves over 99 % classification accuracy, demonstrating its potential for reliable and low-cost monitoring of power device degradation.
- 11 February 2026
- Published by Elsevier in Journal of Crystal Growth
- Vol. 681
Optimization of thermal field on PVT method of 8-inch SiC crystal growth by numerical simulation
- 11 February 2026
- Published by Elsevier in Journal of Crystal Growth
- Vol. 681
Optimization of thermal field on PVT method of 8-inch SiC crystal growth by numerical simulation
- 1 December 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (12) , 12SP16
Study on dislocation propagation in trench structures during scaled Si-IGBTs thermal oxidation
This study investigates the stress and dislocation behavior in trench structures on the silicon chip during the silicon insulated gate bipolar transistor (Si-IGBT) thermal oxidation process. A three-dimensional finite element analysis coupled with the Haasen–Alexander–Sumino dislocation kinetics model was carried out. The results indicate that dislocation propagation during thermal oxidation is highly temperature-dependent, and dislocations primarily form at trench bottom corners due to stress concentration. Trench scaling effectively reduces overall dislocation density by lowering the oxidation temperature. Furthermore, the combination of trench scaling and semicircular trench bottom design decreases dislocation density in stress-concentrated regions, providing guidance for the structural optimization of Si-IGBTs from a defect-suppression perspective.
- 1 December 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64 (12) , 12SP16
Study on dislocation propagation in trench structures during scaled Si-IGBTs thermal oxidation
This study investigates the stress and dislocation behavior in trench structures on the silicon chip during the silicon insulated gate bipolar transistor (Si-IGBT) thermal oxidation process. A three-dimensional finite element analysis coupled with the Haasen–Alexander–Sumino dislocation kinetics model was carried out. The results indicate that dislocation propagation during thermal oxidation is highly temperature-dependent, and dislocations primarily form at trench bottom corners due to stress concentration. Trench scaling effectively reduces overall dislocation density by lowering the oxidation temperature. Furthermore, the combination of trench scaling and semicircular trench bottom design decreases dislocation density in stress-concentrated regions, providing guidance for the structural optimization of Si-IGBTs from a defect-suppression perspective.
- Open Access
- 26 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. PP, 1
Impact of Dislocations on Minority Carrier Lifetime in 300-mm Si Wafers During a High Thermal Budget Process
A quantitatively analysis of the impact of process induced dislocations on minority carrier lifetime in 300-mm Si wafer was presented. High thermal budget processes, such as oxidation and impurity diffusion, are essential in Insulated Gate Bipolar Transistor (IGBT) fabrication but can induce dislocations in large-diameter Si wafers. These dislocations may degrade the minority carrier lifetime, directly impairing device performance. Therefore, establishing a quantitative relationship between dislocation density and lifetime is crucial for process control and yield improvement. In this paper, we first demonstrate that dislocation propagation during thermal processes can be effectively suppressed by controlling the magnitude of a parameter “f”, which represents the dislocation propagation rate. Subsequently, wafers with varying dislocation density were fabricated through a series of consecutive thermal cycles. The dislocation density was determined by numerical calculation, while the corresponding minority carrier lifetime was measured using the micro-photoconductivity decay (l-PCD) method. A quantitative correlation between dislocation density and lifetime was established. These findings contribute to preventing dislocation-induced lifetime degradation during high thermal budget process in power device manufacturing.
- 26 November 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of the Electron Devices Society
- Vol. PP, 1
Open AccessImpact of Dislocations on Minority Carrier Lifetime in 300-mm Si Wafers During a High Thermal Budget Process
A quantitatively analysis of the impact of process induced dislocations on minority carrier lifetime in 300-mm Si wafer was presented. High thermal budget processes, such as oxidation and impurity diffusion, are essential in Insulated Gate Bipolar Transistor (IGBT) fabrication but can induce dislocations in large-diameter Si wafers. These dislocations may degrade the minority carrier lifetime, directly impairing device performance. Therefore, establishing a quantitative relationship between dislocation density and lifetime is crucial for process control and yield improvement. In this paper, we first demonstrate that dislocation propagation during thermal processes can be effectively suppressed by controlling the magnitude of a parameter “f”, which represents the dislocation propagation rate. Subsequently, wafers with varying dislocation density were fabricated through a series of consecutive thermal cycles. The dislocation density was determined by numerical calculation, while the corresponding minority carrier lifetime was measured using the micro-photoconductivity decay (l-PCD) method. A quantitative correlation between dislocation density and lifetime was established. These findings contribute to preventing dislocation-induced lifetime degradation during high thermal budget process in power device manufacturing.
- Open Access
- 1 October 2025
- Published by IOP Publishing in Applied Physics Express
- Vol. 18 (10) , 105501
Reconstruction of physical-vapor-transport SiC growth setup for large crystal height
Reducing SiC wafer cost requires higher usable crystal height and material yield. We reconstruct a single-coil RF-heated physical vapor transport (PVT)-SiC setup using low-cost graphite changes: (i) thermally equalizing insulation from multilayer expanded-graphite sheets and (ii) bottom spacing via a cylindrical spacer. In a 168 h run, we achieved ∼70 mm height with nominal/substantial yields 80.9%/87.0% versus 19.5%/38.2% and reduced gas leakage from 27.2% to 4.1%. Simulations identified ΔT source (axial source-temperature span) as governing; reducing it increases the initial growth rate, independent of configuration. This offers a practical, scalable route to higher PVT-SiC throughput without reactor remodeling or costly components on existing lines.
- 1 October 2025
- Published by IOP Publishing in Applied Physics Express
- Vol. 18 (10) , 105501
Open AccessReconstruction of physical-vapor-transport SiC growth setup for large crystal height
Reducing SiC wafer cost requires higher usable crystal height and material yield. We reconstruct a single-coil RF-heated physical vapor transport (PVT)-SiC setup using low-cost graphite changes: (i) thermally equalizing insulation from multilayer expanded-graphite sheets and (ii) bottom spacing via a cylindrical spacer. In a 168 h run, we achieved ∼70 mm height with nominal/substantial yields 80.9%/87.0% versus 19.5%/38.2% and reduced gas leakage from 27.2% to 4.1%. Simulations identified ΔT source (axial source-temperature span) as governing; reducing it increases the initial growth rate, independent of configuration. This offers a practical, scalable route to higher PVT-SiC throughput without reactor remodeling or costly components on existing lines.
- 1 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Detection of Bond Wire Lift-Off in Switching Tests Using Machine Learning
This study utilised machine learning to analyse the switching waveforms of power semiconductor devices, with a particular focus on wire lift-off and the objective of detecting power cycling failures. Power semiconductor device losses generate heat during the operation of power electronics systems, resulting in power cycling failures. The gate voltage waveform ($V_{g s}$), the drain-source voltage waveform ($V_{d s}$), the source current waveform ($I_{s}$), and the combination of $V_{g s}$ and $I_{s}$ were employed as detection signals, and the accuracy of the analysis was compared using each waveform. Additionally, different types of M-shunts, with and without a coupling area, were utilised for current measurements to examine the effect of deliberate field coupling on the accuracy. The results demonstrate that the analysis employing the $V_{g s}$ waveform and the combined $V_{g s}$ and $I_{s}$ waveforms yield high accuracy for both the turn-off and turn-on conditions, with and without coupling. The use of shunts with coupling structures enables the chosen approach to distinguish between no cut and a single cut. By incorporating coupling structures, the theoretical approach gains practical applicability, as it allows for the detection of slight degradation effects in addition to discrete wire cuts.- 1 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Detection of Bond Wire Lift-Off in Switching Tests Using Machine Learning
This study utilised machine learning to analyse the switching waveforms of power semiconductor devices, with a particular focus on wire lift-off and the objective of detecting power cycling failures. Power semiconductor device losses generate heat during the operation of power electronics systems, resulting in power cycling failures. The gate voltage waveform ($V_{g s}$), the drain-source voltage waveform ($V_{d s}$), the source current waveform ($I_{s}$), and the combination of $V_{g s}$ and $I_{s}$ were employed as detection signals, and the accuracy of the analysis was compared using each waveform. Additionally, different types of M-shunts, with and without a coupling area, were utilised for current measurements to examine the effect of deliberate field coupling on the accuracy. The results demonstrate that the analysis employing the $V_{g s}$ waveform and the combined $V_{g s}$ and $I_{s}$ waveforms yield high accuracy for both the turn-off and turn-on conditions, with and without coupling. The use of shunts with coupling structures enables the chosen approach to distinguish between no cut and a single cut. By incorporating coupling structures, the theoretical approach gains practical applicability, as it allows for the detection of slight degradation effects in addition to discrete wire cuts.- 13 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (10) , 5351-5358
Effect of Substrate Bias in Ohmic p-Gate GaN-HEMTs on Unclamped Inductive Switching Capability
The unclamped inductive switching (UIS) capabilities of ohmic p-gate gallium nitride (GaN)-high electron mobility transistor (HEMT) under various substrate bias conditions were measured. One of the critical disadvantages of GaN-HEMTs is their ultralow UIS capability because there is no structure for the removal of holes generated by the impact ionization. Therefore, the failure position due to overvoltage stress strongly depends on the current path of the holes generated by impact ionization. This article reports that the UIS capability of ohmic p-gate GaN-HEMTs can be improved by a floating or positive biased substrate condition due to the modulation of the hole current path. Additionally, increasing the gate resistance in the floating substrate condition slows down dV/dt, leading to a greater amount of energy being consumed in the semi-on state, which in turn increases the UIS capability.
- 13 August 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (10) , 5351-5358
Effect of Substrate Bias in Ohmic p-Gate GaN-HEMTs on Unclamped Inductive Switching Capability
The unclamped inductive switching (UIS) capabilities of ohmic p-gate gallium nitride (GaN)-high electron mobility transistor (HEMT) under various substrate bias conditions were measured. One of the critical disadvantages of GaN-HEMTs is their ultralow UIS capability because there is no structure for the removal of holes generated by the impact ionization. Therefore, the failure position due to overvoltage stress strongly depends on the current path of the holes generated by impact ionization. This article reports that the UIS capability of ohmic p-gate GaN-HEMTs can be improved by a floating or positive biased substrate condition due to the modulation of the hole current path. Additionally, increasing the gate resistance in the floating substrate condition slows down dV/dt, leading to a greater amount of energy being consumed in the semi-on state, which in turn increases the UIS capability.
- 7 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 38 (2) , 311-323
Modeling and Designing a GaN-Growth Reactor With Halogen-Free Vapor Phase Epitaxy: NH3 Decomposition at the Catalytic Surface of Components to Replicate Parasitic Polycrystal Formation
Achieving long-duration, large bulk GaN growth is crucial to supply low-cost, high-quality GaN. Halogen-free vapor phase epitaxy (HF-VPE) is a promising method for bulk GaN growth but faces challenges due to severe polycrystals deposition on reactor components, such as the source-gas nozzles, which impedes stable, extended growth. In this study, we developed models to simulate the polycrystal deposition in HF-VPE-GaN growth conditions by including surface reactions of GaN formation and NH. decomposition. Moreover, we devised conditions for controlling gas flow and interdiffusion to suppress polycrystal deposition around the source-gas nozzles. Experimental results aligned with simulations, showing that increasing the distance between Ga and NH. nozzles and replacing the sheath gas from H. to N. effectively minimized polycrystal formation. The findings confirm that reducing NH. concentration through catalytic surface decomposition on refractory components is crucial to polycrystal suppression. Optimizing nozzle dimensions and gas species synergistically controls the gas flow and interdiffusion. The constructed models contribute to advancing the design of polycrystal suppressive structures and conditions for long-duration bulk GaN growth.
- 7 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Semiconductor Manufacturing
- Vol. 38 (2) , 311-323
Modeling and Designing a GaN-Growth Reactor With Halogen-Free Vapor Phase Epitaxy: NH3 Decomposition at the Catalytic Surface of Components to Replicate Parasitic Polycrystal Formation
Achieving long-duration, large bulk GaN growth is crucial to supply low-cost, high-quality GaN. Halogen-free vapor phase epitaxy (HF-VPE) is a promising method for bulk GaN growth but faces challenges due to severe polycrystals deposition on reactor components, such as the source-gas nozzles, which impedes stable, extended growth. In this study, we developed models to simulate the polycrystal deposition in HF-VPE-GaN growth conditions by including surface reactions of GaN formation and NH. decomposition. Moreover, we devised conditions for controlling gas flow and interdiffusion to suppress polycrystal deposition around the source-gas nozzles. Experimental results aligned with simulations, showing that increasing the distance between Ga and NH. nozzles and replacing the sheath gas from H. to N. effectively minimized polycrystal formation. The findings confirm that reducing NH. concentration through catalytic surface decomposition on refractory components is crucial to polycrystal suppression. Optimizing nozzle dimensions and gas species synergistically controls the gas flow and interdiffusion. The constructed models contribute to advancing the design of polycrystal suppressive structures and conditions for long-duration bulk GaN growth.