Wenxin Luo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Wenxin Luo has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Mingjie Li
Guangdong University of Technology
8 shared publications - Jianhao Li
School of Integrated Circuits, Guangdong University of Technology, Guangzhou, China
3 shared publications - Wenjun Yan
Hangzhou Dianzi University
3 shared publications - Sihan Yin
Guangdong University of Technology
2 shared publications Yijun Liu
Guangdong University of Technology
2 shared publicationsFa Dai
School of Integrated Circuits, Guangdong University of Technology, Guangzhou, China
1 shared publication
Latest Publications
- 1 November 2026
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 36 (11) , 115006
H 2 and CO identification and concentration prediction using a pulse-driven MEMS gas sensor with multi-feature, multi-task learning
Metal-oxide-semiconductor (MOS) gas sensors are attractive for compact monitoring but remain constrained by cross-reactivity and reliance on steady-state measurements. Here, a suspended Cu–SnO 2 microelectromechanical systems chemiresistor was integrated with a multi-feature, multi-task temporal network for hydrogen (H 2 )/carbon monoxide (CO) identification and quantification. The heater cycled between approximately 90 °C for 0.8 s and 350 °C for 1.6 s at an average power of 19.8 mW. Currents recorded at 10 Hz during 200–900 ppm exposures were transformed into 4.8 s moving-average, Hilbert-envelope, and temporal-derivative channels. Sliding time windows were analyzed using a multi-scale convolutional neural network-squeeze-and-excitation-bidirectional long short-term memory architecture with attention-based classification and gas-specific regression heads. For separately acquired test sequences at 200 and 250 ppm, the three-model ensemble achieved classification accuracy of 99.95% and a gas-only mean absolute error of 25.79 ppm using a 12 s window with a 0.1 s stride in offline replay. These results demonstrate a compact, low-power approach to multi-task gas identification and concentration prediction using a single microsensor.
- 1 November 2026
- Published by IOP Publishing in Journal of Micromechanics and Microengineering
- Vol. 36 (11) , 115006
H 2 and CO identification and concentration prediction using a pulse-driven MEMS gas sensor with multi-feature, multi-task learning
Metal-oxide-semiconductor (MOS) gas sensors are attractive for compact monitoring but remain constrained by cross-reactivity and reliance on steady-state measurements. Here, a suspended Cu–SnO 2 microelectromechanical systems chemiresistor was integrated with a multi-feature, multi-task temporal network for hydrogen (H 2 )/carbon monoxide (CO) identification and quantification. The heater cycled between approximately 90 °C for 0.8 s and 350 °C for 1.6 s at an average power of 19.8 mW. Currents recorded at 10 Hz during 200–900 ppm exposures were transformed into 4.8 s moving-average, Hilbert-envelope, and temporal-derivative channels. Sliding time windows were analyzed using a multi-scale convolutional neural network-squeeze-and-excitation-bidirectional long short-term memory architecture with attention-based classification and gas-specific regression heads. For separately acquired test sequences at 200 and 250 ppm, the three-model ensemble achieved classification accuracy of 99.95% and a gas-only mean absolute error of 25.79 ppm using a 12 s window with a 0.1 s stride in offline replay. These results demonstrate a compact, low-power approach to multi-task gas identification and concentration prediction using a single microsensor.
- Open Access
- 3 September 2026
- Published by AIP Publishing in Nanotechnology and Precision Engineering
- Vol. 10 (1)
Optimizing dynamic pulsing characteristics for highly sensitive and energy-efficient MEMS hydrogen sensors
This study characterizes the effects of dynamic pulsing parameters on hydrogen (H2) gas detection using a novel microheater-integrated metal oxide semiconductor (MOS) sensor. The proposed single-device system operates through duty cycling by utilizing repeated pulsed power inputs. The impact of pulse characteristics, specifically the pulse period and duty cycle, on the overall sensor performance is systematically evaluated. The results demonstrate that operating at an optimal pulse period of 2.4 s with a 67% duty cycle provides a 32% enhancement in the hydrogen response without compromising the response time. In addition, this designed duty-cycling strategy significantly reduces energy consumption, achieving a low average power consumption of ∼19.8 mW. Fabricated using wafer-level batch processing techniques, this compact and energy-efficient sensor platform represents a highly scalable and commercially viable solution for integration into power-constrained Internet of Things monitoring applications.
- 3 September 2026
- Published by AIP Publishing in Nanotechnology and Precision Engineering
- Vol. 10 (1)
Open AccessOptimizing dynamic pulsing characteristics for highly sensitive and energy-efficient MEMS hydrogen sensors
This study characterizes the effects of dynamic pulsing parameters on hydrogen (H2) gas detection using a novel microheater-integrated metal oxide semiconductor (MOS) sensor. The proposed single-device system operates through duty cycling by utilizing repeated pulsed power inputs. The impact of pulse characteristics, specifically the pulse period and duty cycle, on the overall sensor performance is systematically evaluated. The results demonstrate that operating at an optimal pulse period of 2.4 s with a 67% duty cycle provides a 32% enhancement in the hydrogen response without compromising the response time. In addition, this designed duty-cycling strategy significantly reduces energy consumption, achieving a low average power consumption of ∼19.8 mW. Fabricated using wafer-level batch processing techniques, this compact and energy-efficient sensor platform represents a highly scalable and commercially viable solution for integration into power-constrained Internet of Things monitoring applications.
- Top Cited PapersOpen Access
- 23 April 2025
- Published by Springer Nature in Microsystems & Nanoengineering
- Vol. 11 (1) , 1-12
Pulse-driven MEMS gas sensor combined with machine learning for selective gas identification
The sensing and identification of trace gases are essential for ensuring chemical safety and protecting human health. This study introduces a low-power electronic nose system that utilizes a single sensor driven by repeated pulsed power inputs, offering a viable alternative to conventional sensor array-based methods. The sensor’s compact design and suspended architecture facilitate a rapid thermal response, effectively decoupling the influences of temperature, physisorption, and charge exchange on the conductivity of the sensing material. This mechanism generates distinct gas sensing responses, characterized by alternating dual responses within a single time period. The unique dynamics of the dual signals, which vary with gas type and concentration, enable precise identification of multiple gas species using machine learning (ML) algorithms. Microfabricated through wafer-level batch processing, our innovative electronic nose system holds significant potential for battery-powered mobile devices and IoT-based monitoring applications.
- 23 April 2025
- Published by Springer Nature in Microsystems & Nanoengineering
- Vol. 11 (1) , 1-12
Top Cited PapersOpen AccessPulse-driven MEMS gas sensor combined with machine learning for selective gas identification
The sensing and identification of trace gases are essential for ensuring chemical safety and protecting human health. This study introduces a low-power electronic nose system that utilizes a single sensor driven by repeated pulsed power inputs, offering a viable alternative to conventional sensor array-based methods. The sensor’s compact design and suspended architecture facilitate a rapid thermal response, effectively decoupling the influences of temperature, physisorption, and charge exchange on the conductivity of the sensing material. This mechanism generates distinct gas sensing responses, characterized by alternating dual responses within a single time period. The unique dynamics of the dual signals, which vary with gas type and concentration, enable precise identification of multiple gas species using machine learning (ML) algorithms. Microfabricated through wafer-level batch processing, our innovative electronic nose system holds significant potential for battery-powered mobile devices and IoT-based monitoring applications.
- 1 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (11) , 7016-7021
A Single MEMS Sensor Based on SnO₂ Nanosheets for Selective Gas Identification
In recent years, the challenge of poor selectivity in a single gas sensor has received significant interest. This work presents a facile method for the concurrent analysis of sensor temperature variations and conductivity changes in a SnO2 nanosheets-based gas sensor, enabling the selective detection of various gases (such as H2, NH3, and CO). When exposed to reducing gases, the sensor typically exhibits increases in temperature (calorimetric readout) and current (chemo-resistive readout), resulting from the exothermic reaction between the gases and surface oxygen species. The integrated assessment of temperature elevation and conductivity alterations in a single sensor offers an innovative strategy for gas identification and concentration measurement.
- 1 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (11) , 7016-7021
A Single MEMS Sensor Based on SnO₂ Nanosheets for Selective Gas Identification
In recent years, the challenge of poor selectivity in a single gas sensor has received significant interest. This work presents a facile method for the concurrent analysis of sensor temperature variations and conductivity changes in a SnO2 nanosheets-based gas sensor, enabling the selective detection of various gases (such as H2, NH3, and CO). When exposed to reducing gases, the sensor typically exhibits increases in temperature (calorimetric readout) and current (chemo-resistive readout), resulting from the exothermic reaction between the gases and surface oxygen species. The integrated assessment of temperature elevation and conductivity alterations in a single sensor offers an innovative strategy for gas identification and concentration measurement.
- 19 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (19) , 29669-29677
MEMS Gas Sensors Based on In2O3-Decorated SnO2 Nanosheets for Aniline Detection
Aniline monitoring holds significant importance across various industries. In this study, we propose a MEMS gas sensor employing In 2 O 3 -decorated SnO2 nanosheets for aniline detection. Ultrathin nanomaterials were prepared via a facile hydrothermal procedure. The results indicate the gas sensor show excellent sensitivity to aniline, whereas a response (R a /R g ) of 7.3 to 70 ppm aniline was achieved (3 times better than that of pristine SnO 2 ) with a low power consumption of 27.3 mW. The improved sensing characteristics may be ascribed to the synergistic effects arising from the enlarged pore channels and active sites of nanosheets, as well as unique electron transformations and chemical sensitization occurring at the n-n heterojunctions, providing an efficient route for the fabrication of selective aniline gas sensors.
- 19 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (19) , 29669-29677
MEMS Gas Sensors Based on In2O3-Decorated SnO2 Nanosheets for Aniline Detection
Aniline monitoring holds significant importance across various industries. In this study, we propose a MEMS gas sensor employing In 2 O 3 -decorated SnO2 nanosheets for aniline detection. Ultrathin nanomaterials were prepared via a facile hydrothermal procedure. The results indicate the gas sensor show excellent sensitivity to aniline, whereas a response (R a /R g ) of 7.3 to 70 ppm aniline was achieved (3 times better than that of pristine SnO 2 ) with a low power consumption of 27.3 mW. The improved sensing characteristics may be ascribed to the synergistic effects arising from the enlarged pore channels and active sites of nanosheets, as well as unique electron transformations and chemical sensitization occurring at the n-n heterojunctions, providing an efficient route for the fabrication of selective aniline gas sensors.
- 5 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (6) , 7473-7481
Highly Selective MEMS Gas Sensor to Detect H2 and NH3 With Tunable Discrimination
The emerging advancements in gas sensing technology present an ongoing challenge in achieving the selective detection of hydrogen (H 2 ) and ammonia (NH 3 ) gases while allowing for adjustable discrimination. Alternative to conventional isothermal sensing methods, we propose a facile pulsed heating modulation (PHM) strategy to decouple surface physisorption and charge exchange processes. As various gases exhibit distinct activation energies governing physisorption and chemisorption, we demonstrate tunable selectivity by modulating the duty ratio (D) of heating pulses. When operating under PHM with D=0.33, the sensor exhibits favorable selectivity ( S =2.6) to NH 3 , while increasing D to 0.67 enhances selectivity ( S =4.7) for H 2 . In contrast to isothermal techniques, the PHM approach offers a new route for manipulating analyte molecule sensing processes, thereby conferring superior response capabilities and the ability to finely tune selectivity for advanced trillion sensors (TSensors) applications.
- 5 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 24 (6) , 7473-7481
Highly Selective MEMS Gas Sensor to Detect H2 and NH3 With Tunable Discrimination
The emerging advancements in gas sensing technology present an ongoing challenge in achieving the selective detection of hydrogen (H 2 ) and ammonia (NH 3 ) gases while allowing for adjustable discrimination. Alternative to conventional isothermal sensing methods, we propose a facile pulsed heating modulation (PHM) strategy to decouple surface physisorption and charge exchange processes. As various gases exhibit distinct activation energies governing physisorption and chemisorption, we demonstrate tunable selectivity by modulating the duty ratio (D) of heating pulses. When operating under PHM with D=0.33, the sensor exhibits favorable selectivity ( S =2.6) to NH 3 , while increasing D to 0.67 enhances selectivity ( S =4.7) for H 2 . In contrast to isothermal techniques, the PHM approach offers a new route for manipulating analyte molecule sensing processes, thereby conferring superior response capabilities and the ability to finely tune selectivity for advanced trillion sensors (TSensors) applications.
- 29 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (4) , 689-692
Low Concentration CO Gas Sensor Based on Pulsed-Heating and Wafer-Level Fabricated MEMS Hotplate
In recent years, there has been extensive attention focused on enhancing the response of metal oxide semiconductor-based gas sensors. Herein, we propose a simple pulsed-heating approach to decouple physisorption and surface ionosorption of analyte molecules. The gas sensors exhibit excellent electrical response to carbon monoxide (CO) detection (34.3 for 200 ppm), comparable or better than most advanced CO gas sensors. In contrast to the isothermal mode, pulsed-heating allows for sequential control of various gas sensing processes with distinct temperature dependence, offering a new route to improve sensing responses and lower the limit of detection for health and environmental monitoring.
- 29 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (4) , 689-692
Low Concentration CO Gas Sensor Based on Pulsed-Heating and Wafer-Level Fabricated MEMS Hotplate
In recent years, there has been extensive attention focused on enhancing the response of metal oxide semiconductor-based gas sensors. Herein, we propose a simple pulsed-heating approach to decouple physisorption and surface ionosorption of analyte molecules. The gas sensors exhibit excellent electrical response to carbon monoxide (CO) detection (34.3 for 200 ppm), comparable or better than most advanced CO gas sensors. In contrast to the isothermal mode, pulsed-heating allows for sequential control of various gas sensing processes with distinct temperature dependence, offering a new route to improve sensing responses and lower the limit of detection for health and environmental monitoring.
- 5 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (11) , 1981-1984
Wafer-Level Patterning of SnO Nanosheets for MEMS Gas Sensors
In the past few decades, gas sensitive nanomaterials are usually deposited on specific area of the wafer by drop-casting or inkjet printing for application in gas sensor fabrication. However, wafer-level patterning of sensing materials with satisfactory reproducibility still encounters challenge. In this letter, we propose a facile ‘top-down’ strategy to manufacture wafer-scale gas sensing chips with high-throughput by photolithography using a well-mixed photoresist-nanomaterial suspension, followed by calcination. The fabricated gas sensors based on the proposed approach yield excellent reproducibility and uniformity of sensing response to ethanol detection with a relative standard deviation (RSD) <4.5 %, suggesting promising application for high-volume production of MEMS compatible gas sensors.
- 5 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (11) , 1981-1984
Wafer-Level Patterning of SnO Nanosheets for MEMS Gas Sensors
In the past few decades, gas sensitive nanomaterials are usually deposited on specific area of the wafer by drop-casting or inkjet printing for application in gas sensor fabrication. However, wafer-level patterning of sensing materials with satisfactory reproducibility still encounters challenge. In this letter, we propose a facile ‘top-down’ strategy to manufacture wafer-scale gas sensing chips with high-throughput by photolithography using a well-mixed photoresist-nanomaterial suspension, followed by calcination. The fabricated gas sensors based on the proposed approach yield excellent reproducibility and uniformity of sensing response to ethanol detection with a relative standard deviation (RSD) <4.5 %, suggesting promising application for high-volume production of MEMS compatible gas sensors.