Timothy Pickle
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Timothy Pickle has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Zhenzhen Yu
Colorado School of Mines, Golden, USA
4 shared publications - Chad Augustine
National Laboratory of the Rockies, Golden, CO (United States)
3 shared publications - Judith Vidal
National Renewable Energy Laboratory, Golden, CO 80401, USA
2 shared publications - Yu Hong
Colorado School of Mines, Golden, USA
2 shared publications Abdelrahman Abdelmotagaly
1 shared publicationAndy Backhouse
Outokumpu Stainless AB Avesta Sweden
1 shared publication
Latest Publications
- Open Access
- 14 June 2026
- Published by Elsevier in Materialia
- Vol. 48
Strain age cracking in a simulated heat affected zone of Inconel 740H laser-powder bed fusion components
- 14 June 2026
- Published by Elsevier in Materialia
- Vol. 48
Open AccessStrain age cracking in a simulated heat affected zone of Inconel 740H laser-powder bed fusion components
- Open Access
- 25 November 2025
- Published by TIB Open Publishing in SolarPACES Conference Proceedings
- Vol. 3
Evaluation of Alternative Base Materials for Mitigation of Stress Relaxation Cracking in Thermal Energy Storage Tanks
Concentrating solar power (CSP) plants with thermal energy storage (TES) face challenges related to stress relaxation cracking (SRC) in molten hot salt tanks. While alloy 347H stainless steel (SS) is commonly employed due to its stress corrosion cracking (SCC) resistance and sufficient mechanical properties, it suffers from SRC in the weld region. This study explores alloy 1.4910 as a potential alternative, known for its superior creep strength and molten salt corrosion resistance. Thermomechanical testing using a Gleeble® 3500 physical simulator reveals promising results for alloy 1.4910 heat affected zone (HAZ) and 16-8-2 filler (ER16.8.2) fusion zone (FZ), with no cracking observed within a 22-hour test period at elevated temperatures ranging from 600 to 800°C and initial true stress conditions of 650 MPa (0.174 strain) for HAZ and 460 MPa (yield strength) for FZ. In contrast, alloy 347H HAZ and matching filler FZ experienced cracking within a few hours at 800°C. Metallurgical characterization and fractography are additionally conducted on cross welded 1.4910 samples with 16-8-2 filler and thermomechanical Gleeble® samples.
- 25 November 2025
- Published by TIB Open Publishing in SolarPACES Conference Proceedings
- Vol. 3
Open AccessEvaluation of Alternative Base Materials for Mitigation of Stress Relaxation Cracking in Thermal Energy Storage Tanks
Concentrating solar power (CSP) plants with thermal energy storage (TES) face challenges related to stress relaxation cracking (SRC) in molten hot salt tanks. While alloy 347H stainless steel (SS) is commonly employed due to its stress corrosion cracking (SCC) resistance and sufficient mechanical properties, it suffers from SRC in the weld region. This study explores alloy 1.4910 as a potential alternative, known for its superior creep strength and molten salt corrosion resistance. Thermomechanical testing using a Gleeble® 3500 physical simulator reveals promising results for alloy 1.4910 heat affected zone (HAZ) and 16-8-2 filler (ER16.8.2) fusion zone (FZ), with no cracking observed within a 22-hour test period at elevated temperatures ranging from 600 to 800°C and initial true stress conditions of 650 MPa (0.174 strain) for HAZ and 460 MPa (yield strength) for FZ. In contrast, alloy 347H HAZ and matching filler FZ experienced cracking within a few hours at 800°C. Metallurgical characterization and fractography are additionally conducted on cross welded 1.4910 samples with 16-8-2 filler and thermomechanical Gleeble® samples.
- Open Access
- 25 January 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (3) , 657-667
Stress relaxation cracking susceptibility evaluation in 347H stainless steel welds
Stress relaxation cracking (SRC) has been reported as a dominant failure mechanism for 347H stainless steel welds at elevated service temperatures, occurring in either the heat-affected zone (HAZ) or fusion zone (FZ). In this study, SRC susceptibility of physically simulated HAZ and cross-welded E347-347H stainless steel welds was studied using a four-step accelerated SRC test with a thermomechanical physical simulator. The stress and temperature range studied represents weld-induced residual stress at 150–600 MPa and post-weld heat treatment temperatures between 800 and 1050 °C. For all temperature conditions, the cross-welded samples failed at a lower critical stress threshold than the simulated HAZ. A finite element model of a 50.8-mm-thick single-V groove weld was used to generate the residual stress maps induced by a 40-pass welding procedure, which in combination with the experimental threshold stress map predicted potential SRC failure locations. Postmortem microstructural evaluations were performed to identify contributing characteristics to SRC. It was found that HAZ samples exhibited a combination of creep void development, secondary cracks with intergranular fracture near grain boundary carbides, and eutectic phases. FZ samples showed brittle fracture with cracks propagating along straight, non-tortuous interdendritic grain boundaries.
- 25 January 2024
- Published by Springer Nature in Welding in the World
- Vol. 68 (3) , 657-667
Open AccessStress relaxation cracking susceptibility evaluation in 347H stainless steel welds
Stress relaxation cracking (SRC) has been reported as a dominant failure mechanism for 347H stainless steel welds at elevated service temperatures, occurring in either the heat-affected zone (HAZ) or fusion zone (FZ). In this study, SRC susceptibility of physically simulated HAZ and cross-welded E347-347H stainless steel welds was studied using a four-step accelerated SRC test with a thermomechanical physical simulator. The stress and temperature range studied represents weld-induced residual stress at 150–600 MPa and post-weld heat treatment temperatures between 800 and 1050 °C. For all temperature conditions, the cross-welded samples failed at a lower critical stress threshold than the simulated HAZ. A finite element model of a 50.8-mm-thick single-V groove weld was used to generate the residual stress maps induced by a 40-pass welding procedure, which in combination with the experimental threshold stress map predicted potential SRC failure locations. Postmortem microstructural evaluations were performed to identify contributing characteristics to SRC. It was found that HAZ samples exhibited a combination of creep void development, secondary cracks with intergranular fracture near grain boundary carbides, and eutectic phases. FZ samples showed brittle fracture with cracks propagating along straight, non-tortuous interdendritic grain boundaries.
- 1 January 2024
- Published by Office of Scientific and Technical Information (OSTI)
Stress Relaxation Cracking of Alloys at Temperatures Higher Than 540°C
Type 347H stainless steel (347H SS), used in commercial concentrating solar power (CSP) thermal energy storage to store solar-salt at a temperature of 565 C, has been reported in the literature to be susceptible to stress-relaxation cracking (SRC). The welded heat-affected zone (HAZ) and fusion zone (FZ) of 347H SS, particularly in thick sections, are known to be susceptible to failure during post-weld heat treatment (reheat cracking). SRC could also occur after months or years under an elevated-temperature service environment. Two conditions must be present for failure to occur in the HAZ and/or FZ: 1) a modified or sensitized microstructure and 2) sufficiently high tensile residual stresses present at the elevated service temperature. The overarching goal of this project is to recommend SRC mitigation protocols to avoid susceptibility to fail through SRC at temperatures relevant for CSP. Post weld heat treatment conditions and alternative alloys are investigated as potential mitigation solutions to SRC. We used Gleeble thermomechanical simulation tests and finite element (FE) models to understand the susceptibility of 347H SS to SRC as a function of temperature, stress, and microstructure. We started with a literature review of weldability issues with 347H SS and techniques to mitigate SRC in 347Hmore » SS weldments. Next, we used Gleeble experiments to determine reheat cracking susceptibility in the simulated HAZ of 347SS weldments and an alternative alloy, 316L SS (NUCL 167 SPH) with boron added. We also performed Gleeble experiments to compare the reheat cracking susceptibility of 347H cross welded with two different fillers: E347, which is used in some commercial CSP TES tanks, and E16.8.2. We validated the experimental results with FE models of the residual stresses. We found that although the 316L (NUCL 167 SPH) is less susceptible to reheat cracking, it is slightly weaker than 347H and ASME BP&V codes limit its use to a service condition of 565 C. We also found that welds using E16.8.2 as the weld filler are less susceptible to failure than those using E347, likely due to the higher creep ductility of E16.8.2, and that it may be used as an alternative filler for repair welding of 347H welds or as the primary choice of filler for newly developed weld joints. We also found that post weld heat treatment could be a viable solution for mitigating stress in E347-347H SS thick, constrained welds, like those found in CSP tanks, and propose several options for mitigating SRC in existing and future TES tanks. « less
- 1 January 2024
- Published by Office of Scientific and Technical Information (OSTI)
Stress Relaxation Cracking of Alloys at Temperatures Higher Than 540°C
Type 347H stainless steel (347H SS), used in commercial concentrating solar power (CSP) thermal energy storage to store solar-salt at a temperature of 565 C, has been reported in the literature to be susceptible to stress-relaxation cracking (SRC). The welded heat-affected zone (HAZ) and fusion zone (FZ) of 347H SS, particularly in thick sections, are known to be susceptible to failure during post-weld heat treatment (reheat cracking). SRC could also occur after months or years under an elevated-temperature service environment. Two conditions must be present for failure to occur in the HAZ and/or FZ: 1) a modified or sensitized microstructure and 2) sufficiently high tensile residual stresses present at the elevated service temperature. The overarching goal of this project is to recommend SRC mitigation protocols to avoid susceptibility to fail through SRC at temperatures relevant for CSP. Post weld heat treatment conditions and alternative alloys are investigated as potential mitigation solutions to SRC. We used Gleeble thermomechanical simulation tests and finite element (FE) models to understand the susceptibility of 347H SS to SRC as a function of temperature, stress, and microstructure. We started with a literature review of weldability issues with 347H SS and techniques to mitigate SRC in 347Hmore » SS weldments. Next, we used Gleeble experiments to determine reheat cracking susceptibility in the simulated HAZ of 347SS weldments and an alternative alloy, 316L SS (NUCL 167 SPH) with boron added. We also performed Gleeble experiments to compare the reheat cracking susceptibility of 347H cross welded with two different fillers: E347, which is used in some commercial CSP TES tanks, and E16.8.2. We validated the experimental results with FE models of the residual stresses. We found that although the 316L (NUCL 167 SPH) is less susceptible to reheat cracking, it is slightly weaker than 347H and ASME BP&V codes limit its use to a service condition of 565 C. We also found that welds using E16.8.2 as the weld filler are less susceptible to failure than those using E347, likely due to the higher creep ductility of E16.8.2, and that it may be used as an alternative filler for repair welding of 347H welds or as the primary choice of filler for newly developed weld joints. We also found that post weld heat treatment could be a viable solution for mitigating stress in E347-347H SS thick, constrained welds, like those found in CSP tanks, and propose several options for mitigating SRC in existing and future TES tanks. « less