Catur Hilman Adritya Haryo Bhakti Baskoro
Catur Hilman Adritya Haryo Bhakti Baskoro has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Estiko Rijanto
National Research and Innovation Agency
2 shared publications - Nur Safwati Mohd Nor
Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, Johor Bahru 81310, Johor, Malaysia
2 shared publications - Abdullah Iskandar
Waseda University
1 shared publication Ahmad Pahrurrozi
UIN Sunan Gunung Djati Bandung, Elect Engn Dept, Bandung 40614, Indonesia
1 shared publication- Ahmad Pahrurrozi
UIN Sunan Gunung Djati
1 shared publication - Aris Munandar
National Research and Innovation Agency,Research Center of Smart Mechatronics,Bandung,Indonesia
1 shared publication
Latest Publications
- Open Access
- 31 December 2024
- Published by National Research and Innovation Agency in Journal of Mechatronics, Electrical Power, and Vehicular Technology
- Vol. 15 (2) , 208-219
Three-axis flexible tube sensor with LSTM-based force prediction for alignment of electric vehicle charging ports
This paper introduces a novel three-axis flexible tube sensor designed for force measurement in electric vehicle (EV) charging port alignment, utilizing long short-term memory (LSTM) networks. The research aims to develop and validate a flexible and accurate sensor system capable of predicting multi-axis forces during alignment. The sensor integrates a magnetic sensor at the center of a flexible tube to capture three-dimensional (3-D) magnetic field variations corresponding to force changes. Fabricated using thermoplastic polyurethane (TPU) via 3-D printing technology, the sensor leverages machine learning to predict force values along the , , and axes ( , , ). Finite element method (FEM) analysis was conducted to assess the deflection characteristics of the flexible tube under various force conditions. Experimental results demonstrate that integrating LSTM significantly enhances the accuracy of force prediction, achieving an R² score exceeding 97 % for all axes, with mean squared error (MSE) values of 0.2819 for the -axis, 0.3567 for the -axis, and 2.8086 for the -axis. The sensor is capable of measuring forces up to 30 N without exceeding its elastic limits. These findings highlight the sensor’s potential for improving alignment accuracy and reliability in automated EV charging systems.
- 31 December 2024
- Published by National Research and Innovation Agency in Journal of Mechatronics, Electrical Power, and Vehicular Technology
- Vol. 15 (2) , 208-219
Open AccessThree-axis flexible tube sensor with LSTM-based force prediction for alignment of electric vehicle charging ports
This paper introduces a novel three-axis flexible tube sensor designed for force measurement in electric vehicle (EV) charging port alignment, utilizing long short-term memory (LSTM) networks. The research aims to develop and validate a flexible and accurate sensor system capable of predicting multi-axis forces during alignment. The sensor integrates a magnetic sensor at the center of a flexible tube to capture three-dimensional (3-D) magnetic field variations corresponding to force changes. Fabricated using thermoplastic polyurethane (TPU) via 3-D printing technology, the sensor leverages machine learning to predict force values along the , , and axes ( , , ). Finite element method (FEM) analysis was conducted to assess the deflection characteristics of the flexible tube under various force conditions. Experimental results demonstrate that integrating LSTM significantly enhances the accuracy of force prediction, achieving an R² score exceeding 97 % for all axes, with mean squared error (MSE) values of 0.2819 for the -axis, 0.3567 for the -axis, and 2.8086 for the -axis. The sensor is capable of measuring forces up to 30 N without exceeding its elastic limits. These findings highlight the sensor’s potential for improving alignment accuracy and reliability in automated EV charging systems.
- 5 October 2024
- Published by Elsevier in Measurement
- Vol. 242
Characterization of plugging and unplugging process for electric vehicle charging connectors based on Force/Torque measurements
- 5 October 2024
- Published by Elsevier in Measurement
- Vol. 242
Characterization of plugging and unplugging process for electric vehicle charging connectors based on Force/Torque measurements
- Open Access
- 29 December 2023
- Published by National Research and Innovation Agency in Journal of Mechatronics, Electrical Power, and Vehicular Technology
- Vol. 14 (2)
An open-source parallel gripper with an embedded soft skin fingertip sensor
The demand for implementing robots into our daily lives has surged in recent years, necessitating safe grasping for effective interaction with the environment. However, a majority of researchers rely on commercial grippers for their experimental studies, which are typically expensive and not accessible to everyone. Despite the existence of open-source designs, the assembly process is often challenging and requires modifications to enhance secure grasping. This paper presents a simple, compact, and low-cost gripper to offer an accessible and readily deployable solution for research and education. The gripper utilizes a parallel four-bar linkage mechanism, minimizing the number of components and incorporating off-the-shelf parts for straightforward assembly. Furthermore, to enhance its capabilities, the proposed gripper implements a soft skin tactile sensor on its fingertips. These sensors offer three-directional measurements using Hall effect sensing and embedded silicone. By controlling fingertip force based on information from the tactile sensors, the gripper achieves safe grasping. The gripper is evaluated to grasp daily life objects with different properties such as shapes, sizes, and levels of deformability. Evaluation results showcase the gripper's versatility, enabling it to securely grasp various objects, including fragile items. This outcome underscores the gripper's effectiveness, versatility, and safety in practical use.
- 29 December 2023
- Published by National Research and Innovation Agency in Journal of Mechatronics, Electrical Power, and Vehicular Technology
- Vol. 14 (2)
Open AccessAn open-source parallel gripper with an embedded soft skin fingertip sensor
The demand for implementing robots into our daily lives has surged in recent years, necessitating safe grasping for effective interaction with the environment. However, a majority of researchers rely on commercial grippers for their experimental studies, which are typically expensive and not accessible to everyone. Despite the existence of open-source designs, the assembly process is often challenging and requires modifications to enhance secure grasping. This paper presents a simple, compact, and low-cost gripper to offer an accessible and readily deployable solution for research and education. The gripper utilizes a parallel four-bar linkage mechanism, minimizing the number of components and incorporating off-the-shelf parts for straightforward assembly. Furthermore, to enhance its capabilities, the proposed gripper implements a soft skin tactile sensor on its fingertips. These sensors offer three-directional measurements using Hall effect sensing and embedded silicone. By controlling fingertip force based on information from the tactile sensors, the gripper achieves safe grasping. The gripper is evaluated to grasp daily life objects with different properties such as shapes, sizes, and levels of deformability. Evaluation results showcase the gripper's versatility, enabling it to securely grasp various objects, including fragile items. This outcome underscores the gripper's effectiveness, versatility, and safety in practical use.