LSLishuai Sun

Lishuai Sun

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Lishuai Sun has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Integrated framework for modeling, analysis, and optimization of CFRP behavior in mechanical design: A curing deformation case

    by Lishuai Sun, Qianxi Sun

    To achieve high-quality and efficient applications of CFRP (Carbon fiber reinforced polymer) in advanced aerospace, aeronautical, and maritime equipment, this work focuses on the development of an integrated framework for the modeling, analysis, and optimization of composites’ mechanical behavior. This framework aims to serve the entire process of composite design and manufacturing, reduce costs resulting from trial-and-error, and enhance the overall performance and manufacturing quality of new equipment. The framework is introduced through the selection of typical behaviors in composite material applications. First, a theoretical analysis of the generation and forms of these behaviors is conducted, and methods for collecting fundamental data are introduced. To achieve model training based on data, application independent of data, and optimization of the design process while facilitating the promotion and application of the framework, different models are compared and developed. Additionally, methods are introduced for designers to conveniently establish and apply models during structural design, with an example validation using curing deformation in non-symmetric parts. Finally, considering the entire process of composite material part design and optimization, the computational and analytical models are extended, and they are integrated with optimization. This integration enables the enhancement of part performance and subsequent manufacturing precision during the basic and detailed design stages of structural design. The proposed method's convenience and accuracy are demonstrated through a concrete optimization example. The extension of optimization algorithms is similar to the data-independent analysis and computational models, making them easily accessible for designers to establish an integrated framework.

  • An improved approach to compensating for cure‐induced deformation to manufacture composite aircraft skin accurately

    by Chuang Liu, Lishuai Sun, Junbiao Wang

    The purpose of this paper is to compensate for the cure‐induced deformation to manufacture composite aircraft skin with variable curvature accurately. Firstly, a finite element analysis (FEA) method appropriate for curing simulation was described. Then, the discrete curvature‐based displacement adjustment (DC‐DA) method for mold surface compensation was proposed. The DC‐DA method utilizes the discrete curvature of the section points to obtain a smooth compensated curve. Finally, a skin part was selected to prove its effectiveness. The experimental results showed that after the mold's surface was modified by the DC‐DA method with the FEA‐predicting deformation as input, the forming shape could meet the requirement of the part accuracy in one cycle. The DC‐DA method was also compared with the displacement adjustment (DA) method and proved to be more efficient for the compensation of composite skin with variable curvature.Highlights: The FEA is appropriate for the calculation of the skin's curing deformation. The DC‐DA method is efficient for compensating for the skin's deformation. The shape of the case part could meet the requirement of accuracy in one cycle.


  • A novel post‐forming method for fully cured thermosetting composite parts: Prediction and investigation

    by Lishuai Sun, Chenyang Xie, Chuang Liu, Junbiao Wang

    The objective of this work is to devise a post‐forming technique capable of accurately and significantly altering the shape of fully cured thermosetting composite parts. To accomplish this goal, the viscoelastic behavior and resulting deformation of fully cured parts at elevated temperatures were predicted and examined using viscoelastic mechanics, finite element analysis (FEA), surrogate modeling, and the particle swarm optimization (PSO) method. Firstly, the mechanism of fully cured parts' shape adjustment based on viscoelastic mechanics was introduced, and a method was established for the inverse identification of the stress relaxation ratio in the different directions of material. Secondly, an FEA model for predicting post‐forming was developed based on the standard linear‐solid viscoelastic model. A dataset was then compiled using parameterized FEA to train a rapid prediction model for post‐forming. The influence of various forming and structural parameters on the post‐forming process was examined. The results indicate that layup has the most significant impact, followed by displacement and temperature. The radial basis function was selected to construct the precise surrogate model after comparing it with the Kriging model and the Response Surface Methodology (RSM) model. Ultimately, to achieve the desired shape after post‐forming, the PSO method can be employed to determine the ideal combination of forming parameters.Highlights: The post‐forming method could adjust the shape of fully cured composites. The mechanism of post‐forming is based on viscoelastic behavior. An accurate FEA based on the standard linear‐solid model was established. The radial basis function was developed for quick and precise prediction. The particle swarm optimization could obtain the ideal forming parameters.


  • A creep/recovery model of dry fiber fabric during compaction considering temperature and in‐plane tension

    by Yanpeng Si, Le An, Chenyang Xie, Lishuai Sun, Zhiyong Zhao, Yujun Li, Jianjun Jiang

    In the manufacturing of fiber‐reinforced composite materials, the preforming stage of dry fiber fabric entails compaction operations carried out under constant pressure, a specific preforming temperature, and in‐plane tension. Throughout this process, permanent deformation and creep/recovery behavior are observed in the fabric, correlating with factors such as time, sustained pressure, temperature, and in‐plane tension. Effective control of fiber volume fraction and material composition necessitates a thorough comprehension of these phenomena as well as the capacity to predict them with accuracy. To solve this, a viscoelastic‐plastic model was put forth, which provides an account of the viscous effects on the fabric during its stages of compression and recovery. The proposed model incorporates changed Burgers units to manage time‐dependent deformations and plastic units to address permanent deformations. Through the application of a single set of parameters, the model precisely and comprehensively characterizes through‐thickness creep/recovery behavior of preformed dry fiber fabrics under varying conditions, including creep stress, temperature, and in‐plane tension. To enhance the practical utility of the model, an application has been developed and validated against experimental data conducted under diverse test conditions. The results demonstrate consistency between experimental curves and model‐predicted curves across various compression scenarios.Highlights: A viscoelastic‐plastic model was proposed with a single parameter set. Stress, temperature, and in‐plane tension all exacerbated creep/recovery. Model captures temp. and time‐related creep/recovery with in‐plane tension. The model has been transformed into a practical application tool.


  • A rapid and precise approach to predicting the cure‐induced warping of T‐shaped composite parts with inconsistent layup

    by Lishuai Sun, Chuang Liu, Zhiyong Zhao, Junbiao Wang

    This work involved the precise prediction and in‐depth analysis of cure‐induced warping of T‐shaped parts with inconsistent layup. First, the warping mechanism of this kind of part was studied. Then, a finite element analysis (FEA) that considered the parts' structural characteristics and inconsistent layup using the curing mechanical constitutive model was developed to predict the warping. Following verification of the model's accuracy, the effects of material and structural characteristics on warping were investigated. When designing T‐shaped parts, selecting materials with lower thermal expansion coefficients can help minimize warping. Additionally, increasing the radius of the chamfer at the rib and flange connections is also effective. By taking into account the effects of structural parameters and inconsistent layup by using both classical laminated plate theory and artificial neural networks (ANN), a rapid and accurate surrogate model for warping prediction was finally developed. It was discovered that the two‐layer ANN model performed better than the other two models and could predict warping with accuracy and speed. For the parts analyzed in this work, this model is able to identify the fluctuations of warping captured by FEA. Moreover, by defining deviation as the difference between the predicted values of the surrogate model and the FEA, it can be observed that the majority of deviations for the validation set are within ±1.5 mm. This demonstrates that the two‐layer ANN possesses strong generalization ability and high accuracy in predicting warping.Highlights: The inconsistent layup could significantly affect the T‐shaped part's warping. Cutting off a part's rib may significantly reduce its warping. A rapid and accurate model for warping prediction was developed. The layup and structure's influence could be identified by the two‐layer ANN.


  • Bi‐stable cured shape of CFRP variant structures with asymmetric layup: Rapid prediction and inverse design

    by Lishuai Sun, Chuang Liu, Zhiyong Zhao, Junbiao Wang

    This study aims to produce variant composite structures that can precisely maintain equilibrium after changing stable states. A rapid and precise prediction method for the cure‐induced bi‐stable warping was developed, and the inverse design for the required part's structural and material parameters was investigated. Firstly, the mechanism causing the warping was investigated. Then, in order to acquire basic data for a data‐driven model to achieve rapid and accurate warping prediction, a finite element analysis (FEA) was developed, with most of the prediction deviations being under 10%. Additionally, deformation forms of variant parts with various layups and shapes were studied to offer guidance for the different shape requirements. The structural and material parameters were analyzed using the response surface methodology and sensitivity analysis. After removing parameters like all rubbery properties with low influence, basic data from the parameterized FEA was utilized to build a precise proxy model. Finally, for the variant structures requiring reasonable shape forms, the inverse design of the material, layup, and sizes can be achieved using the proxy model and the non‐dominated sorting genetic algorithm II. All optimization results were validated using FEA or experiments. The deformation form in the two steady states of each case meets the specifications. The shape difference between the produced part and the required shape is less than 5 mm, and the design deviation for the maximum deformation is less than 10%. Consequently, the rapid prediction and inverse design methods for the bi‐stable shape of variant composite parts were effective and accurate.Highlights: All the rubbery properties are almost uncorrelated to the bi‐stable warping. The proxy model can rapidly and precisely predict the bi‐stable shape. The inverse design can be achieved for a part requiring proper bi‐stable shapes. The design part can precisely maintain equilibrium with the required shapes.