Taylor Rawlinson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Taylor Rawlinson has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Christopher C. Ferraro
Department of Civil and Coastal Engineering, The University of Florida, Engineering School of Sustainable Infrastructure and the Environment, 365 Weil Hall, P.O. Box 116580, Gainesville, FL 32611, USA
1 shared publication David J. Horhota
State Geotechnical Materials Engineer, Florida Dept. of Transportation, State Materials Office, 5007 Northeast 39th Ave., Gainesville, FL 32609
1 shared publication- Kyle A. Riding
University of Florida
1 shared publication Kyle Riding
1 shared publication- Megan Voss
School of Engineering and Computer Science, University of Evansville,1800 Lincoln Ave., Evansville, IN 47722, USA
1 shared publication - Michael McVay
Professor, Dept. of Civil and Coastal Engineering, Univ. of Florida, 365 Weil Hall, Gainesville, FL 32611
1 shared publication
Latest Publications
- 25 November 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 504
Effect of fiber content on residual CMOD under cyclic and monotonic loading and on self-healing in non-proprietary UHPC
- 25 November 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 504
Effect of fiber content on residual CMOD under cyclic and monotonic loading and on self-healing in non-proprietary UHPC
- Open Access
- 4 June 2023
- Published by Iowa State University
- Vol. 3 (1)
Effects of Time and Consolidation Method on Bond Strength between Fresh UHPC Layers
Full-scale ultra-high performance concrete (UHPC) members often require multiple UHPC batches to meet the required volume. UHPC's "elephant skin" forms quickly and could lead to a weakened interface between the placements. This study investigated placement best practices for multiple UHPC batches to develop procedural specifications that reduce the prevalence of weak interfaces. UHPC mixes staggered in intervals of 10-35 minutes were placed in layers. The flow of the concrete mixes and the resistance of the elephant skin to penetration were measured. A set of three samples from each time interval was rodded, one was externally vibrated, and one was not consolidated (control). After curing, cores were drilled through both layers of concrete and pulloff tests were used to determine bond strength and failure location. Computerized Tomography (CT) scans of select samples were taken to understand how consolidation method affected fiber orientation at the layer interface. Results demonstrate that rodded specimens produced the fewest percentage of interface failures and the highest average strengths, but external vibration also reduced interface failures and increased strength at lower time intervals. CT results showed very few fibers crossing through the concrete interfaces, but rodded specimens had small regions of perpendicular fibers at the locations of rodding.
- 4 June 2023
- Published by Iowa State University
- Vol. 3 (1)
Open AccessEffects of Time and Consolidation Method on Bond Strength between Fresh UHPC Layers
Full-scale ultra-high performance concrete (UHPC) members often require multiple UHPC batches to meet the required volume. UHPC's "elephant skin" forms quickly and could lead to a weakened interface between the placements. This study investigated placement best practices for multiple UHPC batches to develop procedural specifications that reduce the prevalence of weak interfaces. UHPC mixes staggered in intervals of 10-35 minutes were placed in layers. The flow of the concrete mixes and the resistance of the elephant skin to penetration were measured. A set of three samples from each time interval was rodded, one was externally vibrated, and one was not consolidated (control). After curing, cores were drilled through both layers of concrete and pulloff tests were used to determine bond strength and failure location. Computerized Tomography (CT) scans of select samples were taken to understand how consolidation method affected fiber orientation at the layer interface. Results demonstrate that rodded specimens produced the fewest percentage of interface failures and the highest average strengths, but external vibration also reduced interface failures and increased strength at lower time intervals. CT results showed very few fibers crossing through the concrete interfaces, but rodded specimens had small regions of perpendicular fibers at the locations of rodding.