Jiawei Jiang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jiawei Jiang has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Chenglong Tang
State Key Laboratory of Multiphase Flow in Power Engineering
6 shared publications Lihan Fei
3 shared publications- Yuan Li
Xi'an Jiaotong University
2 shared publications - Abrar A. A. Mohsen1 shared publication
Anlong Yang
1 shared publication- Cameron Tropea
Technical University of Darmstadt
1 shared publication
Latest Publications
- 30 September 2026
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 42
Liquid-phase reaction and hypergolic ignition behaviors of H2O2-based green propellants
- 30 September 2026
- Published by Elsevier in Proceedings of the Combustion Institute
- Vol. 42
Liquid-phase reaction and hypergolic ignition behaviors of H2O2-based green propellants
- 5 August 2025
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 193
Statistics of secondary droplets upon impact of a drop onto a solid wall
- 5 August 2025
- Published by Elsevier in International Journal of Multiphase Flow
- Vol. 193
Statistics of secondary droplets upon impact of a drop onto a solid wall
- Open Access
- 15 April 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (16) , 16548-16558
Hypergolic Ignition Behaviors and Propulsive Performance of a Mixture of [AMIm][DCA] with Methanol, Ethanol, and n-Propanol Reacting with White Fuming Nitric Acid
In this article, we study the hypergolic ignition behaviors between a droplet of 1-allyl-3-methylimidazolium dicyanamide ([AMIm][DCA]) blended by methanol/ethanol/n-propanol and a deep white fuming nitric acid oxidizer pool, with an emphasis on the effects of different alcohol additions. Two high-speed cameras with/without a long-distance microscope and an infrared camera are used to capture the details of the ignition process. The main work of this article is listed as following: (1) The hypergolic process generally follows four steps: contact-microexplosion-massive protrusion-ignition, and the difference caused by alcohol addition is analyzed. (2) Average of microexplosion delay time (EDT) and ignition delay time (IDT) of 19 blended fuels is extracted from at least 10 repeat tests. (3) Temperature evolvement could be divided into three stages, and two reaction modes are proposed by characteristics in the temperature evolvement curve and phenomena in the "massive protrusion" stage. (4) The influence of alcohol addition on propulsive performance is predicted by NASA CEA software, and the result indicates that the fuel with a smaller proportion of alcohol and with fewer carbon atoms in added alcohol is less inclined to generate splashing droplets in the massive protrusion stage and has smaller EDT and IDT. When the volume proportion of alcohol is higher than 0.2, fuels blended by different kinds of alcohols exhibit almost the same hypergolic process, EDT, IDT, and temperature evolvement process. Adding all three kinds of alcohols will overall improve the propulsive performance like specific impulse (I sp) slightly. However, considering the significant increase in IDT brought by alcohol addition, the best choice of alcohol addition is methanol to obtain the best reduction in viscosity and the smallest weakening in ignition performance while still slightly improving the propulsive performance.
- 15 April 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (16) , 16548-16558
Open AccessHypergolic Ignition Behaviors and Propulsive Performance of a Mixture of [AMIm][DCA] with Methanol, Ethanol, and n-Propanol Reacting with White Fuming Nitric Acid
In this article, we study the hypergolic ignition behaviors between a droplet of 1-allyl-3-methylimidazolium dicyanamide ([AMIm][DCA]) blended by methanol/ethanol/n-propanol and a deep white fuming nitric acid oxidizer pool, with an emphasis on the effects of different alcohol additions. Two high-speed cameras with/without a long-distance microscope and an infrared camera are used to capture the details of the ignition process. The main work of this article is listed as following: (1) The hypergolic process generally follows four steps: contact-microexplosion-massive protrusion-ignition, and the difference caused by alcohol addition is analyzed. (2) Average of microexplosion delay time (EDT) and ignition delay time (IDT) of 19 blended fuels is extracted from at least 10 repeat tests. (3) Temperature evolvement could be divided into three stages, and two reaction modes are proposed by characteristics in the temperature evolvement curve and phenomena in the "massive protrusion" stage. (4) The influence of alcohol addition on propulsive performance is predicted by NASA CEA software, and the result indicates that the fuel with a smaller proportion of alcohol and with fewer carbon atoms in added alcohol is less inclined to generate splashing droplets in the massive protrusion stage and has smaller EDT and IDT. When the volume proportion of alcohol is higher than 0.2, fuels blended by different kinds of alcohols exhibit almost the same hypergolic process, EDT, IDT, and temperature evolvement process. Adding all three kinds of alcohols will overall improve the propulsive performance like specific impulse (I sp) slightly. However, considering the significant increase in IDT brought by alcohol addition, the best choice of alcohol addition is methanol to obtain the best reduction in viscosity and the smallest weakening in ignition performance while still slightly improving the propulsive performance.
- 1 March 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (3)
Liquid film behavior upon an oblique jet impinging on a solid wall
This work numerically explores the effect of different Reynolds numbers, inclination angles, and wall surface roughness on liquid film behaviors upon a jet impinging on a solid wall. The Volume of Fluid approach with contact angle correction, in conjunction with surface roughness estimation based on boundary layer flow, was applied. A new model for predicting the geometry of the liquid film with full consideration of flow characteristics and jet conditions was proposed. Results show that the present model predicts the maximum liquid film width, the starting point of the liquid film, and the liquid film morphology with improved accuracy. With an increase in jet Reynolds number from 1600 to 3600, the maximum width of the liquid film increases from r/D = 11.8 to 16.5, and the maximum thickness increases from h/D = 1.2 to 1.9. The pressure coefficient shows little change, while the skin friction coefficient decreases with higher Reynolds number. The variation of α from 45° to 75° shows a weak influence on the film thickness distribution in the thin layer zone. Increasing the injection angle results in a downward shift (r/D = 0.8) of the maximum pressure coefficient. The maximum pressure coefficient increases by about 25%, while the maximum skin friction coefficient increases by about 55% with a higher injection angle. With an increase in surface roughness, the maximum width of the liquid film increases about 10%, the maximum pressure coefficient by about 20%, and the maximum skin friction coefficient by about 26%.
- 1 March 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (3)
Liquid film behavior upon an oblique jet impinging on a solid wall
This work numerically explores the effect of different Reynolds numbers, inclination angles, and wall surface roughness on liquid film behaviors upon a jet impinging on a solid wall. The Volume of Fluid approach with contact angle correction, in conjunction with surface roughness estimation based on boundary layer flow, was applied. A new model for predicting the geometry of the liquid film with full consideration of flow characteristics and jet conditions was proposed. Results show that the present model predicts the maximum liquid film width, the starting point of the liquid film, and the liquid film morphology with improved accuracy. With an increase in jet Reynolds number from 1600 to 3600, the maximum width of the liquid film increases from r/D = 11.8 to 16.5, and the maximum thickness increases from h/D = 1.2 to 1.9. The pressure coefficient shows little change, while the skin friction coefficient decreases with higher Reynolds number. The variation of α from 45° to 75° shows a weak influence on the film thickness distribution in the thin layer zone. Increasing the injection angle results in a downward shift (r/D = 0.8) of the maximum pressure coefficient. The maximum pressure coefficient increases by about 25%, while the maximum skin friction coefficient increases by about 55% with a higher injection angle. With an increase in surface roughness, the maximum width of the liquid film increases about 10%, the maximum pressure coefficient by about 20%, and the maximum skin friction coefficient by about 26%.
- 1 March 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Propulsion and Power
- Vol. 40 (2) , 207-219
Novel Hypergolic Green Fuels with Hydrogen Peroxide for Propulsion Systems
By combining the advantages of chemicals from two different classes, a series of catalytically promoted green hypergolic fuels named polyamine/alkanolamine-based hypergolics (PAHyp) with highly concentrated hydrogen peroxide (96%) as an oxidizer was developed. In this paper, a novel recipe based on [ ]-tetramethylethylenediamine (TMEDA) and [ ]-methyldiethanolamine (MDEA), named PAHyp 1, is characterized. Samples with different volume proportions of TMEDA and MDEA catalyzed with 0.5–4 wt% of copper salts were prepared. It was demonstrated that, by adding low catalyst loadings of 1–2 wt%, ultrafast ignition (as low as 8 ms) can be measured. Fast ignition is important to avoid a hard start in the startup phase, and reduced catalyst loading is important to avoid loss of performance in terms of specific impulse. To evaluate the system’s performance, an orbital transfer maneuver of a geostationary satellite that burns monomethylhydrazine with nitrogen tetroxide was considered. It was demonstrated that when using green formulations based on TMEDA/MDEA, smaller propellant tanks are required (because of the higher density of the green propellants), though more propellant mass is required due to a slightly low specific impulse. Besides good performance and reliable ignition, good storability is crucial for long-term space applications. Remarkably, although TMEDA is sensitive to air, visual inspection, ignition tests, and Fourier-transformed infrared spectroscopy analysis revealed that formulations with volume proportions of at least 60% of MDEA stored in vials filled with air survived with no signs of degradation after 14 months. Finally, to meet the requirement of long-term missions of several years in space, a hypergolic tripropellant feed system was proposed.
- 1 March 2024
- Published by American Institute of Aeronautics and Astronautics (AIAA) in Journal of Propulsion and Power
- Vol. 40 (2) , 207-219
Novel Hypergolic Green Fuels with Hydrogen Peroxide for Propulsion Systems
By combining the advantages of chemicals from two different classes, a series of catalytically promoted green hypergolic fuels named polyamine/alkanolamine-based hypergolics (PAHyp) with highly concentrated hydrogen peroxide (96%) as an oxidizer was developed. In this paper, a novel recipe based on [ ]-tetramethylethylenediamine (TMEDA) and [ ]-methyldiethanolamine (MDEA), named PAHyp 1, is characterized. Samples with different volume proportions of TMEDA and MDEA catalyzed with 0.5–4 wt% of copper salts were prepared. It was demonstrated that, by adding low catalyst loadings of 1–2 wt%, ultrafast ignition (as low as 8 ms) can be measured. Fast ignition is important to avoid a hard start in the startup phase, and reduced catalyst loading is important to avoid loss of performance in terms of specific impulse. To evaluate the system’s performance, an orbital transfer maneuver of a geostationary satellite that burns monomethylhydrazine with nitrogen tetroxide was considered. It was demonstrated that when using green formulations based on TMEDA/MDEA, smaller propellant tanks are required (because of the higher density of the green propellants), though more propellant mass is required due to a slightly low specific impulse. Besides good performance and reliable ignition, good storability is crucial for long-term space applications. Remarkably, although TMEDA is sensitive to air, visual inspection, ignition tests, and Fourier-transformed infrared spectroscopy analysis revealed that formulations with volume proportions of at least 60% of MDEA stored in vials filled with air survived with no signs of degradation after 14 months. Finally, to meet the requirement of long-term missions of several years in space, a hypergolic tripropellant feed system was proposed.