Deli Tang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Deli Tang has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Fengfeng Bie
School of Mechanical Engineering and Rail Transit, Changzhou University, Changzhou, Jiangsu, China
3 shared publications - Qianqian Li
College of Energy Engineering, Zhejiang University, Hangzhou, China
3 shared publications - Guoshou Zhao2 shared publications
- Peng Wu
College of Energy Engineering, Zhejiang University, Hangzhou, China
2 shared publications Xiao Lou
2 shared publicationsYi Lu
2 shared publications
Latest Publications
- 1 June 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (6)
Effect of inclination tendency of the channel on the pressure power and energy conversion for regenerative flow pumps
To quantitatively measure the effect of the channel inclination on the pressure power and energy transport dynamics inside the regenerative flow pump, this paper conducts numerical simulation of three models with different inclination coefficients Ic (−0.25, 0, 0.25) to investigate the exchange flow between the rotating impeller and stationary channel. The results show that, the total pressure power (St) in the impeller is linearly increased along the impeller's rotating direction, while some fluctuations existed in the channel due to the unstable mass exchange. The static pressure power (Ss), rather than the dynamic pressure power (Sd), occupies more in St to increase the pressure potential energy of the fluids. Regardless of the model, both the impeller and the channel's static pressure power account for over 60% of the total power. As the Ic increases, both the St and Sd decrease, and the model with outward inclination presents excellent growth of pressure power. Furthermore, energy transport analysis reveals that pressure propulsion work (PPW) is the dominant contributor to the rate of change of kinetic energy (CKE), accounting for more than 65%. In contrast, the Lamb vector divergence and enstrophy contribute less to CKE. The PPW in the impeller is decreased with the increase in Ic, with its positive values primarily distributed near the impeller's shroud side. Compared with the inward inclination channel in model #3, the model #1 with outward inclination accelerates the growth of pressure power, promotes the formation of positive PPW, and improves the hydraulic performance, hence enhancing the fluid's energy exchange and pump's conveying capacity.
- 1 June 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (6)
Effect of inclination tendency of the channel on the pressure power and energy conversion for regenerative flow pumps
To quantitatively measure the effect of the channel inclination on the pressure power and energy transport dynamics inside the regenerative flow pump, this paper conducts numerical simulation of three models with different inclination coefficients Ic (−0.25, 0, 0.25) to investigate the exchange flow between the rotating impeller and stationary channel. The results show that, the total pressure power (St) in the impeller is linearly increased along the impeller's rotating direction, while some fluctuations existed in the channel due to the unstable mass exchange. The static pressure power (Ss), rather than the dynamic pressure power (Sd), occupies more in St to increase the pressure potential energy of the fluids. Regardless of the model, both the impeller and the channel's static pressure power account for over 60% of the total power. As the Ic increases, both the St and Sd decrease, and the model with outward inclination presents excellent growth of pressure power. Furthermore, energy transport analysis reveals that pressure propulsion work (PPW) is the dominant contributor to the rate of change of kinetic energy (CKE), accounting for more than 65%. In contrast, the Lamb vector divergence and enstrophy contribute less to CKE. The PPW in the impeller is decreased with the increase in Ic, with its positive values primarily distributed near the impeller's shroud side. Compared with the inward inclination channel in model #3, the model #1 with outward inclination accelerates the growth of pressure power, promotes the formation of positive PPW, and improves the hydraulic performance, hence enhancing the fluid's energy exchange and pump's conveying capacity.
- 1 October 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (10)
Influence of the channel inclination on the exchange flow and vorticity transport characteristics in a regenerative flow pump
To enhance the overall performance of regenerative flow pump (RFP) to achieve efficient and stable operation over a broad range, this paper employs numerical simulation to study the internal flow conditions of RFP models with three different inclination coefficients (Ic = −0.25, Ic = 0, Ic = 0.25). The analysis focuses on the pressure distribution, energy exchange, velocity variation, and vorticity distribution characteristics within the impeller and channel. The comparison indicates that at Ic = −0.25 with an outward channel, the flow within the pump is stabilized, and the rate of pressure growth and exchange intensity are increased. When Ic = 0 with a semi-circular channel and Ic = 0.25 with an inward channel, there are narrower flow space at the channel's outer diameter, impeding effective fluid motion along the channel and inducing chaotic flow. This condition escalates flow losses and adversely affects the hydraulic performance of the RFP. Additionally, the analysis based on the vorticity transport equation reveals that the Coriolis force term significantly contributes to the generation and transport of vortex in the impeller, while the vortex stretching term dominates the transport of vortex in the channel.
- 1 October 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (10)
Influence of the channel inclination on the exchange flow and vorticity transport characteristics in a regenerative flow pump
To enhance the overall performance of regenerative flow pump (RFP) to achieve efficient and stable operation over a broad range, this paper employs numerical simulation to study the internal flow conditions of RFP models with three different inclination coefficients (Ic = −0.25, Ic = 0, Ic = 0.25). The analysis focuses on the pressure distribution, energy exchange, velocity variation, and vorticity distribution characteristics within the impeller and channel. The comparison indicates that at Ic = −0.25 with an outward channel, the flow within the pump is stabilized, and the rate of pressure growth and exchange intensity are increased. When Ic = 0 with a semi-circular channel and Ic = 0.25 with an inward channel, there are narrower flow space at the channel's outer diameter, impeding effective fluid motion along the channel and inducing chaotic flow. This condition escalates flow losses and adversely affects the hydraulic performance of the RFP. Additionally, the analysis based on the vorticity transport equation reveals that the Coriolis force term significantly contributes to the generation and transport of vortex in the impeller, while the vortex stretching term dominates the transport of vortex in the channel.
- 18 September 2024
- Published by Springer Nature
- p. 135-141
Study on the Vibration Characteristics of a Double-Suction Centrifugal Pump
- 18 September 2024
- Published by Springer Nature
- p. 135-141
Study on the Vibration Characteristics of a Double-Suction Centrifugal Pump
- Open Access
- 1 February 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (2)
Investigation of the unsteady pressure fluctuation mechanism in a regenerative flow pump based on proper orthogonal decomposition
The regenerative flow pump (RFP) derives its name from the circular flow pattern akin to a vortex. However, the presence of numerous vortices results in highly turbulent flow and pressure fluctuation. This study delves into the characteristics of the internal unsteady flow in two distinct RFP models featuring different blade shapes. Numerical simulations are employed to obtain the pressure field, which is subsequently scrutinized using the proper orthogonal decomposition (POD) method. The results show that the average pressure in the peripheral direction undergoes minimal variation during the flow developing stage, experiences a sharp increase in the fully developed stage, and finally exhibits substantial changes in the stripper. The transient pressure in the time domain fluctuates periodically, and the dominant blade passing frequency in the frequency domain demonstrates a similar trend along the circumferential direction as the average pressure. Moreover, the fluctuating intensity of pressure diminishes along the impeller's rotating direction but intensifies significantly in the stripper. Comparative analysis indicates that the exchange intensity is influenced by the flow at different developmental stages, and the exchange flow conditions could reflect the fluctuating intensity. Furthermore, the study reveals that the frequency amplitude of the time coefficient gradually decreases as the mode order increases. The first and second modes exhibit a gradually changing trend associated with pressure increase patterns, whereas the third and fourth modes highlight the emergence of localized modulation phenomena linked to exchange flow. Thus, the POD method offers a unique perspective for comprehending the flow mechanisms within RFPs.
- 1 February 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (2)
Open AccessInvestigation of the unsteady pressure fluctuation mechanism in a regenerative flow pump based on proper orthogonal decomposition
The regenerative flow pump (RFP) derives its name from the circular flow pattern akin to a vortex. However, the presence of numerous vortices results in highly turbulent flow and pressure fluctuation. This study delves into the characteristics of the internal unsteady flow in two distinct RFP models featuring different blade shapes. Numerical simulations are employed to obtain the pressure field, which is subsequently scrutinized using the proper orthogonal decomposition (POD) method. The results show that the average pressure in the peripheral direction undergoes minimal variation during the flow developing stage, experiences a sharp increase in the fully developed stage, and finally exhibits substantial changes in the stripper. The transient pressure in the time domain fluctuates periodically, and the dominant blade passing frequency in the frequency domain demonstrates a similar trend along the circumferential direction as the average pressure. Moreover, the fluctuating intensity of pressure diminishes along the impeller's rotating direction but intensifies significantly in the stripper. Comparative analysis indicates that the exchange intensity is influenced by the flow at different developmental stages, and the exchange flow conditions could reflect the fluctuating intensity. Furthermore, the study reveals that the frequency amplitude of the time coefficient gradually decreases as the mode order increases. The first and second modes exhibit a gradually changing trend associated with pressure increase patterns, whereas the third and fourth modes highlight the emergence of localized modulation phenomena linked to exchange flow. Thus, the POD method offers a unique perspective for comprehending the flow mechanisms within RFPs.
- 25 March 2003
- Published by AIP Publishing in Applied Physics Letters
- Vol. 82 (13) , 2014-2016
Current control for magnetized plasma in direct-current plasma-immersion ion implantation
A method to control the ion current in direct-current plasma-immersion ion implantation (PIII) is reported for low-pressure magnetized inductively coupled plasma. The ion current can be conveniently adjusted by applying bias voltage to the conducting grid that separates plasma formation and implantation (ion acceleration) zones without the need to alter the rf input power, gas flux, or other operating conditions. The ion current that diminishes with an increase in grid bias in magnetized plasmas can be varied from 48 to 1 mA by increasing the grid voltage from 0 to 70 V at −50 kV sample bias and 0.5 mTorr hydrogen pressure. High implantation voltage and monoenergetic immersion implantation can now be achieved by controlling the ion current without varying the macroscopic plasma parameters. The experimental results and interpretation of the effects are presented in this letter. This technique is very attractive for PIII of planar samples that require on-the-fly adjustment of the implantation current at high implantation voltage but low substrate temperature. In some applications such as hydrogen PIII-ion cut, it may obviate the need for complicated sample cooling devices that must work at high voltage.
- 25 March 2003
- Published by AIP Publishing in Applied Physics Letters
- Vol. 82 (13) , 2014-2016
Current control for magnetized plasma in direct-current plasma-immersion ion implantation
A method to control the ion current in direct-current plasma-immersion ion implantation (PIII) is reported for low-pressure magnetized inductively coupled plasma. The ion current can be conveniently adjusted by applying bias voltage to the conducting grid that separates plasma formation and implantation (ion acceleration) zones without the need to alter the rf input power, gas flux, or other operating conditions. The ion current that diminishes with an increase in grid bias in magnetized plasmas can be varied from 48 to 1 mA by increasing the grid voltage from 0 to 70 V at −50 kV sample bias and 0.5 mTorr hydrogen pressure. High implantation voltage and monoenergetic immersion implantation can now be achieved by controlling the ion current without varying the macroscopic plasma parameters. The experimental results and interpretation of the effects are presented in this letter. This technique is very attractive for PIII of planar samples that require on-the-fly adjustment of the implantation current at high implantation voltage but low substrate temperature. In some applications such as hydrogen PIII-ion cut, it may obviate the need for complicated sample cooling devices that must work at high voltage.