Victor M. Denisov
Victor M. Denisov has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Andrey Vl. Timofeev
LLC “AI Center for SCO+ Countries”, Russia
2 shared publications - Aleksandr Titov
Peter the Great St. Petersburg Polytechnic University
1 shared publication Andrei V. Radilov
1 shared publication- Francisco Herlanio Costa Carvalho
Federal University of Ceará
1 shared publication - G.E. Romanova1 shared publication
- Ilya O. Bokatyi
ITMO University, St. Petersburg, Russia
1 shared publication
Latest Publications
- Open Access
- 1 December 2019
- Published by ITMO University in Scientific and Technical Journal of Information Technologies, Mechanics and Optics
- Vol. 124 (6) , 1094
Identification of equipment degradation phase in preventative maintenance systems
Subject of Research. The paper proposes a novel organization technique for preventive maintenance systems (including condition-based and predictive maintenance systems) based on the use of modern machine learning methods. The systems are operating using an original, non-parametric identification method for the current degradation phase of serviced equipment. Method. The proposed method comprises reducing the task of the current phase identification of the equipment degradation phase to interval estimation of the value of the so-called “health index” parameter of the equipment. This parameter is represented as a step function with the arguments in terms of a set of the measurable equipment objective parameters. The current equipment degradation phase is determined by classification approach. At this, based on the analysis of the observed data, it is decided upon what class (state phase) these data correspond to. Measurements from a group of sensors, in general, of various physical nature, which are located both on the surface and inside the equipment being monitored are used as data for identification of the equipment degradation stage. Mathematically, the proposed approach is reduced to a weighted combination of two classifiers. One of the classifiers of this combination is based on solving a group of binary classification problems. The second classifier is based on “Remaining Useful Life” parameter estimation by the method of nonparametric regression. Main Results. As distinguished from traditional approaches, the proposed approach uses a minimum of a priori information about the principles of operation and the internal structure of the equipment being serviced. The approach is based on the usage of the “health index” equipment parameter presented in the form of a step function. The novelty of the approach lies in the simultaneous use of the “health index” step function and the weighted combination of two classifiers with various structure. The proposed method showed good results when being tested on the C-MAPPS Dataset database, which contains data on failures of turbofan engines modeled using a thermodynamic simulation model. The pre-failure status of the equipment is identified with the probability of 99%. Practical Relevance. The obtained results and algorithms can be used in preventive maintenance systems aimed at reliable identification of the equipment degradation current stage.
- 1 December 2019
- Published by ITMO University in Scientific and Technical Journal of Information Technologies, Mechanics and Optics
- Vol. 124 (6) , 1094
Open AccessIdentification of equipment degradation phase in preventative maintenance systems
Subject of Research. The paper proposes a novel organization technique for preventive maintenance systems (including condition-based and predictive maintenance systems) based on the use of modern machine learning methods. The systems are operating using an original, non-parametric identification method for the current degradation phase of serviced equipment. Method. The proposed method comprises reducing the task of the current phase identification of the equipment degradation phase to interval estimation of the value of the so-called “health index” parameter of the equipment. This parameter is represented as a step function with the arguments in terms of a set of the measurable equipment objective parameters. The current equipment degradation phase is determined by classification approach. At this, based on the analysis of the observed data, it is decided upon what class (state phase) these data correspond to. Measurements from a group of sensors, in general, of various physical nature, which are located both on the surface and inside the equipment being monitored are used as data for identification of the equipment degradation stage. Mathematically, the proposed approach is reduced to a weighted combination of two classifiers. One of the classifiers of this combination is based on solving a group of binary classification problems. The second classifier is based on “Remaining Useful Life” parameter estimation by the method of nonparametric regression. Main Results. As distinguished from traditional approaches, the proposed approach uses a minimum of a priori information about the principles of operation and the internal structure of the equipment being serviced. The approach is based on the usage of the “health index” equipment parameter presented in the form of a step function. The novelty of the approach lies in the simultaneous use of the “health index” step function and the weighted combination of two classifiers with various structure. The proposed method showed good results when being tested on the C-MAPPS Dataset database, which contains data on failures of turbofan engines modeled using a thermodynamic simulation model. The pre-failure status of the equipment is identified with the probability of 99%. Practical Relevance. The obtained results and algorithms can be used in preventive maintenance systems aimed at reliable identification of the equipment degradation current stage.
- 6 February 2019
- Published by Springer Nature in Journal of Ambient Intelligence and Humanized Computing
- Vol. 10 (10) , 4121-4134
Biomedical data analytics in mobile-health environments for high-risk pregnancy outcome prediction
- 6 February 2019
- Published by Springer Nature in Journal of Ambient Intelligence and Humanized Computing
- Vol. 10 (10) , 4121-4134
Biomedical data analytics in mobile-health environments for high-risk pregnancy outcome prediction
- Open Access
- 1 November 2018
- Published by ITMO University in Scientific and Technical Journal of Information Technologies, Mechanics and Optics
- Vol. 18 (6) , 932-938
Computer simulation of gamma-ray detector based on scintillation crystals and silicon photomultipliers
Subject of Research. The paper considers the principles of realization of the gamma-radiation detector based on a silicon photoelectron multiplier and a scintillation crystal with the use of an optical matching scheme. Method. For studying the possible variants of detector creation, computer models were developed in the ZEMAX Software environment, describing radiation propagation process of scintillation in the crystal volume in view of the main processes taking place in the scintillation detector. The model has the same optical characteristics as cesium iodide (CsI). Main Results. Quantitative parameters of the signal and radiation losses in modeled systems were obtained. The information on radiation distribution in the photodetector plane was obtained as well. The optimal sheme for detector creation from the registration effectiveness point of view was established and its geometric parameters were determined. Practical Relevance. The development of the approach gives the possibility to solve the problem of creating highly efficient and miniature scintillation detectors at the expense of a new class of photodetectors - silicon photoelectric multipliers. The results of the research will be useful in the development of scintillation gamma spectrometers and other devices with operating principles based on the methods of scintillation spectrometry and radiometry
- 1 November 2018
- Published by ITMO University in Scientific and Technical Journal of Information Technologies, Mechanics and Optics
- Vol. 18 (6) , 932-938
Open AccessComputer simulation of gamma-ray detector based on scintillation crystals and silicon photomultipliers
Subject of Research. The paper considers the principles of realization of the gamma-radiation detector based on a silicon photoelectron multiplier and a scintillation crystal with the use of an optical matching scheme. Method. For studying the possible variants of detector creation, computer models were developed in the ZEMAX Software environment, describing radiation propagation process of scintillation in the crystal volume in view of the main processes taking place in the scintillation detector. The model has the same optical characteristics as cesium iodide (CsI). Main Results. Quantitative parameters of the signal and radiation losses in modeled systems were obtained. The information on radiation distribution in the photodetector plane was obtained as well. The optimal sheme for detector creation from the registration effectiveness point of view was established and its geometric parameters were determined. Practical Relevance. The development of the approach gives the possibility to solve the problem of creating highly efficient and miniature scintillation detectors at the expense of a new class of photodetectors - silicon photoelectric multipliers. The results of the research will be useful in the development of scintillation gamma spectrometers and other devices with operating principles based on the methods of scintillation spectrometry and radiometry
- Open Access
- 1 September 2018
- Published by ITMO University in Scientific and Technical Journal of Information Technologies, Mechanics and Optics
- Vol. 117 (5) , 709-718
Automatic object classification according to 3d-lidar data based on single-photon counting technology
Subject of Research. We compare the effectiveness of the procedure for automatic object classification according to 3d-lidar data, built on the basis of single-photon counting technology, with the efficiency of the classification procedure with the usage of the conventional linear lidar data. Lidars based on the single-photons counting technology (SPCT) significantly exceed the ordinary linear lidars for a whole range of target parameters, including: spatial resolution - by more than an order of magnitude; the performance of the land surface scanning process - by an order of magnitude; by weight and size indicators - few times less. Unlike linear lidars, each laser point in the case of a SPCT-lidar is described not only by its coordinates and the intensity of the reflected signal, but by coordinates and an additional data block that characterizes the surface relief of the probed object in the direction of the probing photon flux. The presence of this additional data block for each laser point makes it possible to consider the received images as 3d-images, that simplifies the solution of not only the photogrammetric problem, but also the task of automatic objects classification on SPCT-image. Method. We consider the automatic object classification task solution based on SPCT-data with the use of the machine learning methods (XGBoost and multilayered neural networks - ANN). Main Results. The results of the numerical simulation carried out within the framework of the present study showed that, other things being equal, the efficiency of solving the classification problem based on SPCT-data, in practically important cases, increases up to 20% compared with the case where the linear-lidar data was used. Practical Relevance. The obtained results can be used in the design of the mobile SPCT-lidars enabling the detection and classification of objects on the Earth's surface in real time with high reliability.
- 1 September 2018
- Published by ITMO University in Scientific and Technical Journal of Information Technologies, Mechanics and Optics
- Vol. 117 (5) , 709-718
Open AccessAutomatic object classification according to 3d-lidar data based on single-photon counting technology
Subject of Research. We compare the effectiveness of the procedure for automatic object classification according to 3d-lidar data, built on the basis of single-photon counting technology, with the efficiency of the classification procedure with the usage of the conventional linear lidar data. Lidars based on the single-photons counting technology (SPCT) significantly exceed the ordinary linear lidars for a whole range of target parameters, including: spatial resolution - by more than an order of magnitude; the performance of the land surface scanning process - by an order of magnitude; by weight and size indicators - few times less. Unlike linear lidars, each laser point in the case of a SPCT-lidar is described not only by its coordinates and the intensity of the reflected signal, but by coordinates and an additional data block that characterizes the surface relief of the probed object in the direction of the probing photon flux. The presence of this additional data block for each laser point makes it possible to consider the received images as 3d-images, that simplifies the solution of not only the photogrammetric problem, but also the task of automatic objects classification on SPCT-image. Method. We consider the automatic object classification task solution based on SPCT-data with the use of the machine learning methods (XGBoost and multilayered neural networks - ANN). Main Results. The results of the numerical simulation carried out within the framework of the present study showed that, other things being equal, the efficiency of solving the classification problem based on SPCT-data, in practically important cases, increases up to 20% compared with the case where the linear-lidar data was used. Practical Relevance. The obtained results can be used in the design of the mobile SPCT-lidars enabling the detection and classification of objects on the Earth's surface in real time with high reliability.