Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Xiangbiao Liao has a total of 75 co-authors. Here are the top co-authors by number of shared publications:

  • Jingyi Qiu

    Chemical Defense Institute Beijing People's Republic of China

    3 shared publications
  • Xiao Wang

    National‐Provincial Laboratory of Special Function Thin Film Materials School of Materials Science and Engineering Xiangtan University Xiangtan 411105 China

    3 shared publications
  • Yixin Luo

    School of Interdisciplinary Science Beijing Institute of Technology Beijing People's Republic of China

    3 shared publications
  • Yong Pan

    National‐Provincial Laboratory of Special Function Thin Film Materials School of Materials Science and Engineering Xiangtan University Xiangtan 411105 China

    3 shared publications
  • Yuyang Lu

    3 shared publications
  • Aoyan Geng

    2 shared publications

Latest Publications

  • Open Access

    Chemical Bonding Interface Enables Lithium Batteries to Operate Under Near‐Vacuum Conditions

    by Rongrong Guo, Songmei Li, Xiaoyun Xu, Wenqiang Zhang, Yixin Luo, Jinyan Zhong, Jingyi Qiu, Shubin Yang, Bin Li, Xiangbiao Liao

    The reliance on high stack pressure in lithium metal batteries (LMBs) conflicts with the requirements of lightweight design and low‐pressure operating environments, motivating the development of pressure‐independent battery designs. Here, a chemical bonding interfacial prototype is proposed to substitute the physical contact interface, thereby liberating LMBs from high stacking pressures. This chemical bonding interface is constructed via strong interactions between the carbonyl groups of poly(ε‐caprolactone) segments and Li metal, manifesting as Li─O bonding interfaces. Benefiting from Li─O bonding, the PPE electrolyte exhibits a high adhesion energy of 22.44 J m −2 and a high lap shear strength of 0.31 MPa, sustaining intimate electrode–electrolyte contact without external stack pressure. In addition, the Li─O bonding interface significantly reduces the thickness of the electric double layer, achieving a 120% increase in capacitance (0.20 µF cm −2 ), thus promoting efficient transport (t Li+ = 0.7) and uniform deposition of Li + . As a result, the Li||Cu half‐cell equipped with PPE electrolyte achieves a superior coulombic efficiency of 99.78%. A pouch cell equipped with PPE electrolyte and NCM cathode demonstrates high capacity retention of 90.12% after 40 cycles at −0.1 MPa (relative to standard atmospheric pressure). This discovery offers novel insights into material and structural design for pressure‐insensitive batteries intended for high‐altitude aerospace applications.

  • Open Access

    Quantifying the Correlation Between Capacity Utilization and Electrolyte Dosage for Ultrahigh‐Energy‐Density 769 Wh Kg −1 Rechargeable Lithium Metal Batteries

    by Shuo Zhang, Yuyang Lu, Chong Yan, Xiangbiao Liao, Chen‐Zi Zhao, Jun‐Wei Zhao, Zhiyuan Dong, Zhenwei Zhu, Wenjie Meng, Xue‐Fei Wen, et al.

    The pursuit of high‐energy‐density lithium metal batteries requires simultaneous optimization of electrode architecture, electrolyte formulation, and interfacial stability. Here, we establish a fundamental parameter g(σ e , D e ) that quantifies the relationship between electrolyte dosage and capacity utilization in ultra‐thick electrodes (>100.0 µm), enabling precise determination of the minimal electrolyte requirement (1.1 g Ah −1 ). Through systematic investigation of electrolyte compatibility with high‐loading cathodes (> 10.0 mAh cm −2 ) at high voltages (4.8 V), we develop an optimized formulation that forms stable interfaces while suppressing parasitic reactions. By integrating these advances—including a lightweight lithium metal anode—we demonstrate a 54.2 Ah pouch cell achieving 769 Wh kg −1 , representing a 150% improvement over conventional lithium‐ion batteries. This work provides both theoretical and practical frameworks for engineering next‐generation batteries through electrolyte minimization and interface stabilization.


  • Open Access

    Enhanced Refrigerant-Based Thermal Management System for Lithium Batteries with Rapid Temperature Response

    by Shubin Yin, Bonian Zhou, Wei Zhao, Wei Ji, Xiangbiao Liao, Jingyi Qiu, Yong Tang, Shiwei Zhang

  • Open Access

    Fast-charging induced lithium crosstalk: A culprit for calendar aging of silicon-graphite electrodes

    by Xinya Niu, Lige Chang, Chengcheng Cao, Yuyang Lu, Xiangbiao Liao, Linghui He, Yong Ni

    While significant efforts have improved the fast-charging performance of silicon-graphite (Si-Gr) composite anodes, the impact of fast charging on surface side reactions and calendar aging under lithium crosstalk remains poorly understood. This study combines experimental observations with simulations using an electrochemical-mechanical-side reaction model. We find that fast charging creates a large electric potential gap between Si and Gr, intensifying lithium crosstalk. This crosstalk drives continuous solid electrolyte interphase (SEI) growth on Si during calendar aging, causing persistent loss of cyclable lithium. The potential gap can be mitigated by regulating lithium partitioning between Si and Gr, suppressing crosstalk-induced SEI growth. By rationally tailoring the intrinsic lithium diffusivity and particle size of Si, an optimal lithium partitioning between Si and Gr can be achieved under high C-rate conditions, which not only mitigates crosstalk-induced SEI growth but also concurrently relieves mechanical stress within the composite electrode. Our findings redefine the role of fast-charging induced lithium crosstalk in governing long-term degradation and provide actionable guidelines for the rational design of Si-Gr composite electrodes with enhanced calendar life.

  • Damage evolution of metalized plastic current collectors induced by particle indentation during calendering

    by Aoyan Geng, Zhiwei Chen, Junpeng Feng, Yanchang Liu, Yixin Luo, Zhiqun Liu, Yuyang Lu, Xibang Chen, Xiangbiao Liao

  • Open Access

    Damage Evolution of Metallized Plastic Current Collectors Induced by Particle Indentation during Calendering

    by Aoyan Geng, Zhiwei Chen, Junpeng Feng, Yanchang Liu, Yixin Luo, Zhiqun Liu, Yuyang Lu, Xibang Chen, Xiangbiao Liao

    Metalized plastic current collectors (MPCCs) with metal layers deposited on both sides of an ultrathin polymer substrate are promising substitute for conventional metal current collectors to enhance safety and energy density of lithium-ion batteries (LIBs). However, large compression in the calendering process easily induces mechanical damage in MPCCs due to its poor mechanical properties, potentially increasing the failure risk of electrodes during subsequent battery assembly and cycling. Here, the damage evolution and mechanical-electrical failure mechanisms of Cu/PET MPCCs and Al/PET MPCCs under the calendering process are investigated. Experiments and finite element simulations show that the tensile component contributes marginally to calendering induced damage because of the small tensile strain during calendering. In contrast, the compression driven by active particles on MPCCs dominates the damage evolution, and leads to pronounced degradation in both mechanical and electrical performance. Cu/PET MPCCs mainly undergo localized plastic deformation at high compaction densities, whereas Al/PET MPCCs are prone to interfacial delamination due to the weak interfacial adhesion. Simulations further indicate that calendering induced defects increase the failure risk under the tensile loading from subsequent roll-to-roll winding. These findings provide mechanistic guidance for calendering parameter optimization and MPCC design.

  • A Bifunctional Shear‐Thickened Composite Electrolyte Toward High‐Safety Lithium Metal Batteries

    by Yuan Liu, Zhenya Luo, Yao Zhou, Huang Kang, Yutong Jiang, Xiao Wang, Weiguo Mao, Cuiying Dai, Yong Pan, Xiangbiao Liao, et al.

    Lithium metal batteries (LMBs) are limited in practical applications due to safety issues resulting from uncontrolled dendrite growth and mechanical abuse. Herein, a bifunctional gel shear‐thickened electrolyte (STE) is developed to simultaneously prevent lithium dendrite growth and improve impact protection by dispersing hydroxyl‐rich fumed silica in a conventional liquid electrolyte (LE). STE in Li||Cu cells enabled a lower overpotential for Li deposition compared to that using LE. Li|STE|Li cells stably cycled 1200 h, while Li|LE|Li cells only survived for 200 h, which is attributed to STE promoting the formation of the stable inorganic‐rich SEI. Li|STE|LFP full cells achieved capacity retention of 77% after 200 cycles, much higher than LE‐containing cells (54%@200 cycles). In addition, the superior protection performance of STE‐containing pouch cells is verified by in‐situ monitoring with digital image correlation technology and theoretical analysis with finite element simulation. Compared with the pouch cell without STE, the maximum principal strain and plastic strain of the STE‐containing pouch cell are reduced by 80% and 62.5%, respectively, which benefits from the non‐Newtonian fluid behavior of STE under impact loading. This work confirmed the great potential of the bifunctional gel electrolyte for enhancing the electrochemical performance and safety of LMBs.


  • A flexible porous polyimide/copper composite film toward high-mass-loading anodes in lithium-ion batteries

    by Xiao Wang, Junhao Wang, Shi Liu, Tonghao Zhou, Yihang Li, Zhenya Luo, Yong Pan, Xiangbiao Liao, Junan Pan


  • Open Access

    Motorizing the buckled blister for rotary actuation

    by Pengfei Yang, Ruixing Huang, Fei Dang, Baoxiang Shan, Dewen Wang, Hong Liu, Yi Li, Xiangbiao Liao

    Snap‐through bistability was widely exploited for rapid hopping in micro‐electro‐mechanical systems and soft robots. However, considerable energy input was required to trigger the transition between discrete buckling states blocked by potential wells. Here a dynamic buckling mechanism of a buckled blister constrained inside an outer ring is explored for eliciting rotary actuation via a localized change of curvature in the blister. Due to rotational invariance of the buckled blister, lower energy supply is required to initiate the snap‐through of buckling compared to conventional bistable mechanism. The controllability in rotational speed and output torque of the bimetallic blister‐based rotator inside a rigid stator is exhibited, and the locomotion is demonstrated with two elastic rings via localized pneumatic actuators. With broad choices of stimulus and material for rings, the findings illustrate the promising potential of two nested rings to create active motions for diverse applications including gearless motors, peristaltic pumps, and locomotive robots.