YHYufa Hu

Yufa Hu

*This is an algorithmically generated author record based on publicly available information.

Yufa Hu has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Experimental investigation on the hypersonic boundary layer transition induced by side-by-side cylinders

    by Xiwang Xu, Zihao Ye, Shihe Yi, Yufa Hu, Lican Wang

    The flow-field structure and heat-flux distribution around the isolated cylinder and side-by-side cylinders on the flat-plate at different angles-of-attack (AoA) and free stream conditions are investigated in a Mach 6 low noise wind tunnel, using nano-tracer-based planar laser scattering (NPLS) techniques and the temperature sensitive paint techniques. The results indicate that the interaction of the bow-shaped shock waves between adjacent cylinders generates an “X”-shaped high-heat-flux region, but this high-heat-flux region only appears near the intersection of the shock waves. Downstream of the shock wave intersection, due to the formation of low-density vortices structures between adjacent cylinders, a low-heat-flux region appears. Further downstream, the boundary layer reattaches, resulting in reattachment shock waves and high-heat-flux strips appearing on the wall surface. The NPLS results show that the horseshoe vortices/bow shock wave interaction between parallel cylinders will cause the position of the shock wave formed after the intersection to move forward and increase the thickness of the boundary layer and the number of low-density vortices structures, but the position of the reattached shock wave hardly changes. As the AoA decreases, the length of the low-heat-flux region between adjacent cylinders increases, and the reattachment position of the boundary layer shifts backward. Notably, the mutual influence between parallel cylinders mainly occurs in the outer horseshoe vortices region, while having a relatively small impact on the streamwise vortices directly behind the cylinders.

  • Influences of steps on hypersonic boundary layer instability over a cone at small angle of attack

    by Xiwang Xu, Shihe Yi, Yufa Hu, Zihao Ye, Lin He

    The influences of the forward-facing step (FFS) and backward-facing step (BFS) on the 7° half-angle cone's boundary layer instability at different meridians are investigated at Mach 6, with step heights of 0.6 mm, and a 1° angle of attack (AoA) in a hypersonic quiet wind tunnel using the Nano-tracer-based Planar Laser Scattering techniques, and high-frequency pressure sensors. The results show that at AoA = 1°, the instability that dominates conical boundary layer transition is the second-mode wave. At a given streamwise location, as the position approaches the centerline of the leeward side, the frequency of the second-mode wave decreases while its amplitude increases, resulting in a more unstable boundary layer. Moreover, the development of the second-mode waves in the BFS model progresses faster than that in the FFS model, at different meridians. Notably, on the leeward side, the FFS stabilizes the second-mode waves, whereas the BFS model destabilizes them.


  • Effect of wall-seeping gas film on hypersonic laminar and transitional boundary layers

    by Yufa Hu, Shihe Yi, Xiaolin Liu, Xudong Tian

    The wall-seeping gas film (WSGF) is a promising technology for controlling hypersonic boundary layer transition. Experiments were conducted in a Mach 6 hypersonic quiet wind tunnel with freestream unit Reynolds numbers Re∞ = 7.3 × 106 m−1 and 14.6 × 106 m−1, corresponding to the WSGF being present in the laminar and transitional boundary layers, respectively. The effect of seeping ratios on the hypersonic boundary layer instability and transition was investigated using nano-tracer-based planar laser scattering (NPLS) technique and high-frequency wall fluctuating pressure sensors. The results indicate that WSGF exhibits opposite effects in the laminar and transitional boundary layers. Under all examined seeping ratios, WSGF significantly promotes transition at Re∞ = 7.3 × 106 m−1, accompanied by the premature appearance of second-mode instability waves. The maximum peak amplitude occurs at x = 420 mm, where the nonlinear interactions of instability waves are strongest. However, at Re∞ = 14.6 × 106 m−1, WSGF with moderate seeping ratios (0.072%–0.280%) extends the development distance of the second-mode waves characterized by a frequency range of 80–140 kHz. The boundary layer relaminarizes downstream of the seeping wall. The turbulence burst point was delayed by up to 14% at a seeping ratio of 0.141%. These opposite effects of WSGF on the laminar and transitional boundary layers further confirm the notion that the relative position of the WSGF to the synchronization point is a more critical factor.


  • Evolution of supersonic cooling film flow over concave and convex surfaces with different radius curvatures

    by Zhen Zhang, Xiaolin Liu, Shihe Yi, Yufa Hu

    A cooling film (Mach 2.3) is injected into a supersonic wind tunnel's (Mach 3.8) flow field. As the curvature radius decreases, mixing layer destabilization is delayed on the CV (convex wall) and advanced on the CC (concave wall). When x = 20–60 mm, wall pressure is influenced by the cooling film, and when x = 100–220 mm, curvature dominates. As the curvature radius decreases, pressure on the concave wall increases more rapidly, while that on the convex wall decreases more swiftly. IP (impulse for bulk dilation) values on the CC-1500 and CV-1500 walls are approximately twice those on the CC-3000 and CV-3000 walls, respectively.


  • Effect of wall microstructure on conical hypersonic boundary layer flow

    by Zhen Zhang, Shihe Yi, Xiaolin Liu, Yufa Hu

    As an effective boundary layer flow control method, wall microstructure has an important application prospect in heat and drag reduction of hypersonic. In this paper, based on experimental techniques such as high-frequency pressure fluctuation testing, the effects of different microstructure configurations (V-shaped and rectangular) and distribution modes (streamwise and transverse) on the flow of hypersonic conic boundary layer under the condition of Mach 6 hypersonic incoming flow are studied. The experimental results show that compared with the flow of the smooth wall boundary layer, the wall microstructure has a greater influence on the eigenfrequency of the second-mode wave in the boundary layer, and the streamwise increases by about 20 kHz to the rectangular microstructure and decreases by about 30 kHz to the transverse rectangular microstructure. At the same time, the transverse V-shaped microstructure can increase the amplitude of the second mode in the boundary layer by 5.5 times compared with the smooth wall. For the evolution of boundary layer flow, the microstructure arranged along the flow direction will accelerate the linear development of the disturbance wave during the transition, so that the laminar flow will be transformed into turbulent flow in a shorter distance. The microstructure arranged along the transverse direction prolongs the linear development stage of the disturbance wave during the transition, so that the laminar flow turns into turbulent flow over a longer distance. Downstream of different structures, it is shown that transverse rectangular microstructure has lowest temperatures.


  • Supersonic cooling film flow evolution on a curved wall under hypersonic flow

    by Zhen Zhang, Shihe Yi, Xiaolin Liu, Yufa Hu, Shikang Chen

    Curvature plays a crucial role in evolving supersonic cooling film flow-field structures. Flow-field structural images were captured using nanotracer-based planar laser scattering,, and wall pressure values were obtained using experimentally validated numerical simulations. A supersonic cooling film is tangentially injected at the Mach number of Maj = 2.3 into a laminar boundary layer at a mainstream of Ma = 6. The supersonic cooling film inhibits mixing-layer instability on the convex curved wall (CV) and promotes it on the concave curved wall (CC). After increasing the total incoming pressure, the reduction ratio of static pressure (RSP) between the supersonic cooling film and the mainstream flow causes a delay in the position of the mixing-layer instability, smaller-scale vortex structures, and decreased flow velocity of the typical vortex structures on the CC and CV. The wall pressure increases for the CV and decreases for the CC, indicating that the supersonic cooling film suppresses the changes in wall pressure due to curvature. The supersonic cooling film suppresses the decrease in the impulses for bulk dilatation (Ip) due to convex curvature and the increase in Ip due to concave curvature. The growth rate of Ip on the CC increases from −15% to −8% and decreases on the CV from 31% to 12% in the bending impulse (IΦ) range of |IΦ| = 1.337–3.624 for a total inlet pressure of 0.5 MPa. Increasing the RSP could control the Ip values on curved surfaces more effectively. The results of this study can be applied to cooling the infrared optics window on hypersonic vehicles.