Andrea Corrado
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andrea Corrado has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Matteo Benedetti
Department of Industrial Engineering, University of Trento, Trento, Italy
4 shared publications - Matteo Perini
ProM Facility, Rovereto, Italy
3 shared publications - Charline van Innis2 shared publications
- Raffaele De Biasi
Department of Industrial Engineering, University of Trento, 38123 Trento, Italy
2 shared publications - Rosemere de Araujo Alves Lima
IDMEC, Instituto Superior Técnico, Universidade de Lisboa Lisboa Portugal
2 shared publications - Sofia Teixeira de Freitas
Delft University of Technology
2 shared publications
Latest Publications
- Open Access
- 10 August 2026
- Published by Elsevier in SSRN Electronic Journal
Mode I fracture of co-bonded CFRP to 316L joints with additively manufactured lattice interfaces: role of topology and elastoplastic homogenization
This study investigates the fracture behavior of co-bonded joints between Carbon Fiber Reinforced Polymers and 316L Stainless Steel manufactured by Laser Powder Bed Fusion, with the aim of improving the reliability of multi-material joints and reduce assembly time. To promote adhesive interlocking between the two materials and reduce dependence on both surface preparation and metal type, the metal adherends were designed with interface lattice patterns. Mode I fracture toughness is evaluated through Double Cantilever Beam tests, supported by post-mortem analysis, which provides valuable insights into the effects of the pattern. Among the investigated topologies, the TPMS Gyroid unit cell exhibited the highest amount of cohesive failure thanks to its morphology and hence, it achieved a fracture toughness approximately 40 % higher than the Simple Cubic (SC) unit cell. A homogenized 3D Finite Element Model of DCB tests, which includes 3D elasto‐plastic behavior and Cohesive Zone Model, successfully reproduced the experimental load-displacement curve while maintaining low computational cost. Overall, this study demonstrates that surface lattice patterns in bi-material joints effectively anchor and retain the adhesive within the interface cavities, with TPMS Gyroid significantly enhancing Mode I fracture toughness compared to the SC unit cell, while elasto-plastic homogenization of the adhesive infilled unit cells enables a computationally efficient and accurate FE modeling of bi-material joints.
- 10 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessMode I fracture of co-bonded CFRP to 316L joints with additively manufactured lattice interfaces: role of topology and elastoplastic homogenization
This study investigates the fracture behavior of co-bonded joints between Carbon Fiber Reinforced Polymers and 316L Stainless Steel manufactured by Laser Powder Bed Fusion, with the aim of improving the reliability of multi-material joints and reduce assembly time. To promote adhesive interlocking between the two materials and reduce dependence on both surface preparation and metal type, the metal adherends were designed with interface lattice patterns. Mode I fracture toughness is evaluated through Double Cantilever Beam tests, supported by post-mortem analysis, which provides valuable insights into the effects of the pattern. Among the investigated topologies, the TPMS Gyroid unit cell exhibited the highest amount of cohesive failure thanks to its morphology and hence, it achieved a fracture toughness approximately 40 % higher than the Simple Cubic (SC) unit cell. A homogenized 3D Finite Element Model of DCB tests, which includes 3D elasto‐plastic behavior and Cohesive Zone Model, successfully reproduced the experimental load-displacement curve while maintaining low computational cost. Overall, this study demonstrates that surface lattice patterns in bi-material joints effectively anchor and retain the adhesive within the interface cavities, with TPMS Gyroid significantly enhancing Mode I fracture toughness compared to the SC unit cell, while elasto-plastic homogenization of the adhesive infilled unit cells enables a computationally efficient and accurate FE modeling of bi-material joints.
- Open Access
- 26 March 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 36, 2977-2993
Lightweight design of polymeric thin-walled components: Latticization and elastic–plastic homogenization
- 26 March 2025
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 36, 2977-2993
Open AccessLightweight design of polymeric thin-walled components: Latticization and elastic–plastic homogenization
- Open Access
Hybrid Single Lap Joints between 3D Printed Titanium Lattices and CFRP Composites: Experimental and Numerical Insights
In the contemporary emphasis on weight reduction, the utilization of advanced materials like Carbon Fiber Reinforced Polymers (CFRPs) and cutting-edge technologies such as 3D printing of metal is increasingly crucial. This study delves into the junction of CFRP and titanium, aiming to conduct Single Lap shear tests on specimens featuring a co-lamination of long fiber composite onto a metal lattice structure. Different specimens with different dimensions of the Simple Cubic (SC) unit cell were subjected to testing. A microscope investigation facilitated an exploration of junction failure and epoxy resin infiltration into the lattice substrate. Employing an efficient 2D Finite Element Model, the homogenization process yielded theoretical models underestimating the Young Modulus by approximately 10% compared to real specimens. Despite the challenges in bonding titanium and CFRP, the novel junction exhibited a shear stress of 17.25 MPa, which is nearly equivalent to those of a co-lamination between sandblasted steel and CFRP, that is 17.15 MPa.
Open AccessHybrid Single Lap Joints between 3D Printed Titanium Lattices and CFRP Composites: Experimental and Numerical Insights
In the contemporary emphasis on weight reduction, the utilization of advanced materials like Carbon Fiber Reinforced Polymers (CFRPs) and cutting-edge technologies such as 3D printing of metal is increasingly crucial. This study delves into the junction of CFRP and titanium, aiming to conduct Single Lap shear tests on specimens featuring a co-lamination of long fiber composite onto a metal lattice structure. Different specimens with different dimensions of the Simple Cubic (SC) unit cell were subjected to testing. A microscope investigation facilitated an exploration of junction failure and epoxy resin infiltration into the lattice substrate. Employing an efficient 2D Finite Element Model, the homogenization process yielded theoretical models underestimating the Young Modulus by approximately 10% compared to real specimens. Despite the challenges in bonding titanium and CFRP, the novel junction exhibited a shear stress of 17.25 MPa, which is nearly equivalent to those of a co-lamination between sandblasted steel and CFRP, that is 17.15 MPa.