Po-Cheng Lai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Po-Cheng Lai has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Chih-Lung Lin
Department of Electrical Engineering, National Cheng Kung University, Tainan, Taiwan
6 shared publications - Cheng-Han Ke
Department of Electrical Engineering, National Cheng Kung University, Tainan, Taiwan
3 shared publications - Jui-Hung Chang
Department of Electrical Engineering, National Cheng Kung University, Tainan, Taiwan
3 shared publications Li-Wei Shih
Department of Electrical Engineering, National Cheng Kung University, Tainan, Taiwan
3 shared publications- Yi-Chien Chen
Department of Electrical Engineering, National Cheng Kung University, Tainan, Taiwan
3 shared publications Yu-Chang Chiu
Department of Electrical Engineering, National Cheng Kung University, Tainan, Taiwan
3 shared publications
Latest Publications
- 8 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (5) , 2609-2614
LTPS TFT-Based Optical Sensor Detecting Degradation of OLED to Improve Image Sticking for AMOLED Displays
An in-pixel optical sensor with threshold voltage (VTH) compensation is proposed to maintain the brightness of a panel after long-term use of an active-matrix organic light-emitting diode (AMOLED) display. The proposed optical-sensing mechanism measures the ratio of the variation in the driving current to detect the decay in the brightness of the panel, which compensates for the reduced brightness and extends the lifetime of the OLED display. The proposed circuit also compensates for variation in the threshold voltage for a low-temperature polycrystalline thin-film transistor (LTPS TFTs) to increase the accuracy of sensing the electrical characteristics of the driving TFTs, which reduces the error in the measured brightness ratio. To validate the compensation performance, a simulation model that uses fabricated LTPS TFTs and an optical sensor with silicon-rich oxide (SRO) is established. The simulation results confirm that the maximum normalized current error rate decreases from 20.90% to 0.36% when the brightness of the panel decays by 10% if the proposed circuit is used compared to the original active pixel sensor (APS) 3T circuit. A 1.28-in LTPS AMOLED display that uses the proposed in-cell optical sensor is fabricated. The proposed circuit successfully compensates for the degradation. The maximum brightness ratio error is only 1.00%, and the image sticking is improved by sensing variations in the driving currents using the proposed circuit when brightness decays by over 5%. This verifies the feasibility of the proposed pixel circuit for use in AMOLED displays with an in-pixel optical sensor.
- 8 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (5) , 2609-2614
LTPS TFT-Based Optical Sensor Detecting Degradation of OLED to Improve Image Sticking for AMOLED Displays
An in-pixel optical sensor with threshold voltage (VTH) compensation is proposed to maintain the brightness of a panel after long-term use of an active-matrix organic light-emitting diode (AMOLED) display. The proposed optical-sensing mechanism measures the ratio of the variation in the driving current to detect the decay in the brightness of the panel, which compensates for the reduced brightness and extends the lifetime of the OLED display. The proposed circuit also compensates for variation in the threshold voltage for a low-temperature polycrystalline thin-film transistor (LTPS TFTs) to increase the accuracy of sensing the electrical characteristics of the driving TFTs, which reduces the error in the measured brightness ratio. To validate the compensation performance, a simulation model that uses fabricated LTPS TFTs and an optical sensor with silicon-rich oxide (SRO) is established. The simulation results confirm that the maximum normalized current error rate decreases from 20.90% to 0.36% when the brightness of the panel decays by 10% if the proposed circuit is used compared to the original active pixel sensor (APS) 3T circuit. A 1.28-in LTPS AMOLED display that uses the proposed in-cell optical sensor is fabricated. The proposed circuit successfully compensates for the degradation. The maximum brightness ratio error is only 1.00%, and the image sticking is improved by sensing variations in the driving currents using the proposed circuit when brightness decays by over 5%. This verifies the feasibility of the proposed pixel circuit for use in AMOLED displays with an in-pixel optical sensor.
- Open Access
- 11 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Solid-State Circuits Society
- Vol. 5, 130-143
LTPO-TFT-Based Pixel Circuit With TFT, OLED, and Supply Voltage Compensation for Enhanced Luminance Uniformity in Variable-Frame-Rate AMOLED Smartwatch Displays
This work proposes a new pixel circuit using low-temperature polycrystalline silicon and oxide (LTPO) thin-film transistors (TFTs) for use in variable-frame-rate active-matrix organic light-emitting diode (AMOLED) smartwatch displays. The proposed circuit, including seven TFTs and two capacitors, can compensate for threshold voltage (VTH) variations of the driving TFTs (DTFTs), the turn-on voltages of the OLEDs (VOLEDs), and VSS IR rises; it is immune to VDD IR drops. It employs amorphous-indium-gallium-zinc-oxide (a-IGZO) TFTs, which exhibit low leakage currents, suppressing distortion in the gate voltage of the DTFT at low frame rates and enabling a stable OLED current (IOLED) to maintain consistent display luminance. A 1.28-inch LTPO AMOLED panel with a 416 W 416 resolution and the proposed pixel circuit are fabricated to verify the circuits performance. The experimental results thus obtained confirm that red, green, blue, and white images at frame rates from 45 Hz to 1 Hz exhibit uniformity without visible spot or line defects and a luminance error rate below 2.34 remain stable at gray levels of 32, 64, 128, and 255 during an extended emission period of 1 s, revealing no perceived image flicker at 1 Hz (with a JEITA flicker value below -54.747 dB). Therefore, the proposed circuit, with its highly uniform and stable currents at various frame rates, is promising for use in AMOLED smartwatch displays.
- 11 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of the Solid-State Circuits Society
- Vol. 5, 130-143
Open AccessLTPO-TFT-Based Pixel Circuit With TFT, OLED, and Supply Voltage Compensation for Enhanced Luminance Uniformity in Variable-Frame-Rate AMOLED Smartwatch Displays
This work proposes a new pixel circuit using low-temperature polycrystalline silicon and oxide (LTPO) thin-film transistors (TFTs) for use in variable-frame-rate active-matrix organic light-emitting diode (AMOLED) smartwatch displays. The proposed circuit, including seven TFTs and two capacitors, can compensate for threshold voltage (VTH) variations of the driving TFTs (DTFTs), the turn-on voltages of the OLEDs (VOLEDs), and VSS IR rises; it is immune to VDD IR drops. It employs amorphous-indium-gallium-zinc-oxide (a-IGZO) TFTs, which exhibit low leakage currents, suppressing distortion in the gate voltage of the DTFT at low frame rates and enabling a stable OLED current (IOLED) to maintain consistent display luminance. A 1.28-inch LTPO AMOLED panel with a 416 W 416 resolution and the proposed pixel circuit are fabricated to verify the circuits performance. The experimental results thus obtained confirm that red, green, blue, and white images at frame rates from 45 Hz to 1 Hz exhibit uniformity without visible spot or line defects and a luminance error rate below 2.34 remain stable at gray levels of 32, 64, 128, and 255 during an extended emission period of 1 s, revealing no perceived image flicker at 1 Hz (with a JEITA flicker value below -54.747 dB). Therefore, the proposed circuit, with its highly uniform and stable currents at various frame rates, is promising for use in AMOLED smartwatch displays.
- 10 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (11) , 6769-6773
N-Type Low-Temperature Polycrystalline Silicon and Amorphous Oxide Thin-Film Transistor-Based Robust Dual-Output Gate Driver
This work presents a dual-output gate driver that is based on low-temperature polycrystalline silicon and amorphous oxide (LTPO) thin-film transistors (TFTs) and supports bidirectional transmission. This gate driver generates positive and negative pulses for both n-type and p-type switching TFTs in display pixels, effectively reducing the bezel area. Simulation results indicate that the output waveforms remain undistorted even when the threshold voltage (${V}_{\text {TH}}$ ) of low-temperature polycrystalline silicon (LTPS) TFTs varies by ±0.46 V and the${V}_{\text {TH}}$ of the amorphous indium gallium zinc oxide (a-IGZO) TFTs shifts by +0.56 V. This gate driver achieves short rising/falling times of approximately 1.25/$1.42~\mu $ s for a positive pulse and 1.55/$2.73~\mu $ s for a negative pulse through the output circuit composed of LTPS TFTs during forward transmissions. When operated at 1 Hz, the output waveforms are correctly generated and stabilized at +6.6 V and −6.6 by the stabilization circuit, which includes a-IGZO TFTs. Therefore, the proposed gate driver is promising for use in low-frame-rate smartwatch displays.- 10 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (11) , 6769-6773
N-Type Low-Temperature Polycrystalline Silicon and Amorphous Oxide Thin-Film Transistor-Based Robust Dual-Output Gate Driver
This work presents a dual-output gate driver that is based on low-temperature polycrystalline silicon and amorphous oxide (LTPO) thin-film transistors (TFTs) and supports bidirectional transmission. This gate driver generates positive and negative pulses for both n-type and p-type switching TFTs in display pixels, effectively reducing the bezel area. Simulation results indicate that the output waveforms remain undistorted even when the threshold voltage (${V}_{\text {TH}}$ ) of low-temperature polycrystalline silicon (LTPS) TFTs varies by ±0.46 V and the${V}_{\text {TH}}$ of the amorphous indium gallium zinc oxide (a-IGZO) TFTs shifts by +0.56 V. This gate driver achieves short rising/falling times of approximately 1.25/$1.42~\mu $ s for a positive pulse and 1.55/$2.73~\mu $ s for a negative pulse through the output circuit composed of LTPS TFTs during forward transmissions. When operated at 1 Hz, the output waveforms are correctly generated and stabilized at +6.6 V and −6.6 by the stabilization circuit, which includes a-IGZO TFTs. Therefore, the proposed gate driver is promising for use in low-frame-rate smartwatch displays.- 5 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (9) , 5528-5534
LTPO-TFT Compensating Pixel Structure Reduces Thermally Generated Leakage Current in Low-Frame-Rate AMOLED Displays
This work proposes a new pixel circuit that is based on low-temperature polycrystalline silicon and oxide (LTPO) thin-film transistors (TFTs) for use in low-frame-rate smartwatch active-matrix organic light-emitting diode (AMOLED) displays. The LTPO circuit features a leakage-balancing structure that includes amorphous indium-gallium-zinc oxide (a-IGZO) TFTs, which suppresses voltage distortion at the gate node of the driving TFT (D-TFT) and stabilizes the OLED current ( ${I}_{\text {OLED}}$ ) at high temperatures. To achieve a pure black image, the anode of each OLED is actively discharged during the reset period to release the accumulated charge. The feasibility of the proposed circuit is evaluated using TFT models that were developed from experimental data on 1.28-in display panels. Analytical results reveal that the relative current error rates are below 5.87% and 5.45% at $25~^{\circ }$ C and $85~^{\circ }$ C, respectively, with a ±0.3 V change in the threshold voltage ( ${V}_{\text {TH}}$ ) of p-type D-TFT. At $85~^{\circ }$ C, ${I}_{\text {OLED}}$ s maintain low current deviation rates at different gray levels during a prolonged emission period of 1 s, demonstrating the high feasibility of using the proposed circuit for low-frame-rate operation of AMOLED displays.
- 5 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (9) , 5528-5534
LTPO-TFT Compensating Pixel Structure Reduces Thermally Generated Leakage Current in Low-Frame-Rate AMOLED Displays
This work proposes a new pixel circuit that is based on low-temperature polycrystalline silicon and oxide (LTPO) thin-film transistors (TFTs) for use in low-frame-rate smartwatch active-matrix organic light-emitting diode (AMOLED) displays. The LTPO circuit features a leakage-balancing structure that includes amorphous indium-gallium-zinc oxide (a-IGZO) TFTs, which suppresses voltage distortion at the gate node of the driving TFT (D-TFT) and stabilizes the OLED current ( ${I}_{\text {OLED}}$ ) at high temperatures. To achieve a pure black image, the anode of each OLED is actively discharged during the reset period to release the accumulated charge. The feasibility of the proposed circuit is evaluated using TFT models that were developed from experimental data on 1.28-in display panels. Analytical results reveal that the relative current error rates are below 5.87% and 5.45% at $25~^{\circ }$ C and $85~^{\circ }$ C, respectively, with a ±0.3 V change in the threshold voltage ( ${V}_{\text {TH}}$ ) of p-type D-TFT. At $85~^{\circ }$ C, ${I}_{\text {OLED}}$ s maintain low current deviation rates at different gray levels during a prolonged emission period of 1 s, demonstrating the high feasibility of using the proposed circuit for low-frame-rate operation of AMOLED displays.
- Open Access
- 9 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 78122-78131
Lifetime Optimization of Optical Sensing System With Highly Reliable a-Si:H TFT-Based Optical Sensor and Driver Circuit in Large AMLCDs
This paper presents a long-lifetime optical sensing system that integrates optical sensors and driver circuits that use hydrogenated amorphous silicon thin-film transistors (a-Si:H TFTs) to realize binary detection of optical signal with a multi-position sensing function for use in large active-matrix liquid crystal display (AMLCD). The optical sensor suppresses the effect of variations in ambient white light using a white-light photocurrent gating (WPCG) structure and increases the reliability of two photo TFTs by halving the drain-to-source voltage (VDS) stress. The driver circuit switches two driving TFTs between their two modes to recover the threshold voltage (VTH) shifts during a long sensing period or generate an output waveform with a large pulse width for driving the optical sensor. Experimental results indicate that the degradation of the photocurrent of the photo TFT is suppressed from 3.71 nA to 1.03 nA, representing an improvement of 72.2% relative to the original WPCG structure. The minimum difference between the output voltages of the optical sensing systems with and without an optical signal under illumination by ambient white light from 500 to 10000 lux is 18.58 V. According to an accelerated lifetime test, the feasibility of using the optical sensing system in large AMLCDs is verified.
- 9 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 78122-78131
Open AccessLifetime Optimization of Optical Sensing System With Highly Reliable a-Si:H TFT-Based Optical Sensor and Driver Circuit in Large AMLCDs
This paper presents a long-lifetime optical sensing system that integrates optical sensors and driver circuits that use hydrogenated amorphous silicon thin-film transistors (a-Si:H TFTs) to realize binary detection of optical signal with a multi-position sensing function for use in large active-matrix liquid crystal display (AMLCD). The optical sensor suppresses the effect of variations in ambient white light using a white-light photocurrent gating (WPCG) structure and increases the reliability of two photo TFTs by halving the drain-to-source voltage (VDS) stress. The driver circuit switches two driving TFTs between their two modes to recover the threshold voltage (VTH) shifts during a long sensing period or generate an output waveform with a large pulse width for driving the optical sensor. Experimental results indicate that the degradation of the photocurrent of the photo TFT is suppressed from 3.71 nA to 1.03 nA, representing an improvement of 72.2% relative to the original WPCG structure. The minimum difference between the output voltages of the optical sensing systems with and without an optical signal under illumination by ambient white light from 500 to 10000 lux is 18.58 V. According to an accelerated lifetime test, the feasibility of using the optical sensing system in large AMLCDs is verified.
- 25 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (3) , 400-403
Resolving Issues of VTH and ILeak for P-Type LTPS TFT-Based Emission Gate Driver by Reducing Falling Time and Increasing Stabilizing Period for Smartwatch Displays
This work proposes an emission (EM) gate driver that is based on p-type low-temperature poly-crystalline silicon thin-film transistors (LTPS TFTs) with the implementation of lightly doped drain (LDD) to achieve flat off current. The long-tail phenomenon associated with the EM signal that is caused by a high threshold voltage (VTH) and (VTH variation in LTPS TFTs is improved by enhancing the driving capability of the pull-down TFT. The pulse width of the EM signal is adjustable, and the gate driver has a stabilizing structure to reduce the voltage deviation caused by the high leakage current ( $\text{I}_{\text {Leak}}{)}$ of LTPS TFTs; it keeps the EM signal at its lowest voltage level for 96.7% of the duration of a frame. Measurements indicate that the proposed structure shortens the falling time of the EM signal to $3.815 ~\mu \text{s}$ , which is much shorter than a horizontal time of $46 ~\mu \text{s}$ , yielding an EM signal with low distortion. An accelerated lifetime test demonstrates the high reliability of the proposed gate driver, which has the potential for driving active-matrix organic light-emitting diodes (AMOLEDs) smartwatch displays.
- 25 December 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (3) , 400-403
Resolving Issues of VTH and ILeak for P-Type LTPS TFT-Based Emission Gate Driver by Reducing Falling Time and Increasing Stabilizing Period for Smartwatch Displays
This work proposes an emission (EM) gate driver that is based on p-type low-temperature poly-crystalline silicon thin-film transistors (LTPS TFTs) with the implementation of lightly doped drain (LDD) to achieve flat off current. The long-tail phenomenon associated with the EM signal that is caused by a high threshold voltage (VTH) and (VTH variation in LTPS TFTs is improved by enhancing the driving capability of the pull-down TFT. The pulse width of the EM signal is adjustable, and the gate driver has a stabilizing structure to reduce the voltage deviation caused by the high leakage current ( $\text{I}_{\text {Leak}}{)}$ of LTPS TFTs; it keeps the EM signal at its lowest voltage level for 96.7% of the duration of a frame. Measurements indicate that the proposed structure shortens the falling time of the EM signal to $3.815 ~\mu \text{s}$ , which is much shorter than a horizontal time of $46 ~\mu \text{s}$ , yielding an EM signal with low distortion. An accelerated lifetime test demonstrates the high reliability of the proposed gate driver, which has the potential for driving active-matrix organic light-emitting diodes (AMOLEDs) smartwatch displays.