Hongzhuo Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hongzhuo Liu has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Baoyong Chi
School of Integrated Circuits, Tsinghua University, Beijing, China
6 shared publications - Haikun Jia
School of Integrated Circuits, Tsinghua University, Beijing, China
6 shared publications - Wei Deng
Tsinghua University
6 shared publications - Zhihua Wang
Tsinghua University
5 shared publications Shiyan Sun
School of Integrated Circuits, Tsinghua University, Beijing, China
3 shared publicationsShiwei Zhang
School of Integrated Circuits, Tsinghua University, Beijing, China
2 shared publications
Latest Publications
- 30 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (4) , 1589-1602
A Cycle-Slip Compensated FMCW Digital PLL With Background Back-Tracking DPD
This article introduces an 11.4-to-16.4-GHz digital phase-locked loop (PLL) for chirp generation in frequency-modulated continuous-wave (FMCW) radars. The PLL is implemented in a frequency-domain, type-II two-point modulation (TPM) structure. A cycle-slip compensation scheme is proposed to identify overflow events in the time-to-digital converter (TDC) and correct the miscalculated frequency error, thereby improving chirp linearity during fast chirp generation. To reduce frequency errors caused by frequency overlaps in a multi-bank digitally controlled oscillator (DCO), a back-tracking digital pre-distortion (DPD) scheme is introduced to ensure robust convergence despite capacitor mismatch-induced asymmetric frequency overlaps in triangular chirp modulations. The FMCW digital PLL, implemented in a 28-nm CMOS technology, consumes 10 mW of power and occupies an area of 0.19 mm2. It is capable of generating a frequency modulation (FM) chirp with a 960-MHz/ $\mu $ s slope and a 3.84-GHz bandwidth while achieving a normalized rms FM error of 0.032%.
- 30 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 61 (4) , 1589-1602
A Cycle-Slip Compensated FMCW Digital PLL With Background Back-Tracking DPD
This article introduces an 11.4-to-16.4-GHz digital phase-locked loop (PLL) for chirp generation in frequency-modulated continuous-wave (FMCW) radars. The PLL is implemented in a frequency-domain, type-II two-point modulation (TPM) structure. A cycle-slip compensation scheme is proposed to identify overflow events in the time-to-digital converter (TDC) and correct the miscalculated frequency error, thereby improving chirp linearity during fast chirp generation. To reduce frequency errors caused by frequency overlaps in a multi-bank digitally controlled oscillator (DCO), a back-tracking digital pre-distortion (DPD) scheme is introduced to ensure robust convergence despite capacitor mismatch-induced asymmetric frequency overlaps in triangular chirp modulations. The FMCW digital PLL, implemented in a 28-nm CMOS technology, consumes 10 mW of power and occupies an area of 0.19 mm2. It is capable of generating a frequency modulation (FM) chirp with a 960-MHz/ $\mu $ s slope and a 3.84-GHz bandwidth while achieving a normalized rms FM error of 0.032%.
- 25 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 8, 141-144
A Series-Parallel-Resonance Oscillator With a 191.5 dBc/Hz FoM
To achieve robust ultra-low phase noise (PN) and a high figure of merit (FoM), this letter proposes a series-parallelresonance oscillator topology based on the following ideas: 1) a low-impedance resonator that supports high power consumption and effective PN suppression within a compact layout; 2) impedance and gain boosting for PN-power trade-off, sharper transition, and active noise reduction. Prototyped in 65nm CMOS technology, the proposed X-band oscillator demonstrates a PN of -131.4 dBc/Hz at 1MHz offset, a FoM of 191.5 dBc/Hz, and a FoMA(i.e. FoM with area) of 198.5 dBc/Hz at 10GHz with quadrature output.
- 25 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 8, 141-144
A Series-Parallel-Resonance Oscillator With a 191.5 dBc/Hz FoM
To achieve robust ultra-low phase noise (PN) and a high figure of merit (FoM), this letter proposes a series-parallelresonance oscillator topology based on the following ideas: 1) a low-impedance resonator that supports high power consumption and effective PN suppression within a compact layout; 2) impedance and gain boosting for PN-power trade-off, sharper transition, and active noise reduction. Prototyped in 65nm CMOS technology, the proposed X-band oscillator demonstrates a PN of -131.4 dBc/Hz at 1MHz offset, a FoM of 191.5 dBc/Hz, and a FoMA(i.e. FoM with area) of 198.5 dBc/Hz at 10GHz with quadrature output.
- 16 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (3) , 785-798
An Ultra-Low-Jitter Fast-Hopping Fractional-N PLL With LC DTC and Hybrid-Proportional Paths
This work presents an ultra-low-jitter fractional-N PLL capable of wideband fast hopping. There is an analog proportional path and a digital proportional/integral path in the PLL. The PLL is digital-path-dominant during settling and analog-path-dominant after settles; therefore, the fast-lock characteristic of the digital PLLs and the low-jitter characteristic of the analog PLLs are achieved. The frequency switching algorithm does not rely on the linearity of DCO’s tuning curve, nor rely on the hopping step between the previously locked frequency and the target frequency. The frequency detection is based on a high-speed counter, which uses the quadruple timing margin selection and can operate up to 20 GHz. The counter is integrated with a feedback clock generator, which is functionally the same as a multi-modulus divider. In addition, this work proposes an LC delay circuit as the coarse digital-to-time converter (DTC), which has better potential than the RC-based counterparts to reduce the phase noise of DTC and thereby reduce the jitter of fractional-N PLLs. The prototype is implemented in 28-nm CMOS process and occupies 0.21-mm2 core area. The measured hopping time is $0.52~{\mu }$ s across a 3.5-GHz step with 80-ppm settling accuracy. The measured rms jitter (integrated from 1 kHz to 100 MHz) is 36.8 fs for the integer-N channel, 41.3 fs for the far-integer fractional-N channel, and 61.7 fs for the near-integer fractional-N channel. The measured near-integer fractional spur is -62.4 dBc. The measured power consumption is 34 mW.
- 16 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (3) , 785-798
An Ultra-Low-Jitter Fast-Hopping Fractional-N PLL With LC DTC and Hybrid-Proportional Paths
This work presents an ultra-low-jitter fractional-N PLL capable of wideband fast hopping. There is an analog proportional path and a digital proportional/integral path in the PLL. The PLL is digital-path-dominant during settling and analog-path-dominant after settles; therefore, the fast-lock characteristic of the digital PLLs and the low-jitter characteristic of the analog PLLs are achieved. The frequency switching algorithm does not rely on the linearity of DCO’s tuning curve, nor rely on the hopping step between the previously locked frequency and the target frequency. The frequency detection is based on a high-speed counter, which uses the quadruple timing margin selection and can operate up to 20 GHz. The counter is integrated with a feedback clock generator, which is functionally the same as a multi-modulus divider. In addition, this work proposes an LC delay circuit as the coarse digital-to-time converter (DTC), which has better potential than the RC-based counterparts to reduce the phase noise of DTC and thereby reduce the jitter of fractional-N PLLs. The prototype is implemented in 28-nm CMOS process and occupies 0.21-mm2 core area. The measured hopping time is $0.52~{\mu }$ s across a 3.5-GHz step with 80-ppm settling accuracy. The measured rms jitter (integrated from 1 kHz to 100 MHz) is 36.8 fs for the integer-N channel, 41.3 fs for the far-integer fractional-N channel, and 61.7 fs for the near-integer fractional-N channel. The measured near-integer fractional spur is -62.4 dBc. The measured power consumption is 34 mW.
- 5 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (2) , 529-542
A Transformer-Based Series-Resonance CMOS VCO
The LC parallel tank is widely used in oscillators, and its noise optimization techniques are relatively mature. However, there has always been a bottleneck in phase noise (PN) performance, and the multi-core technique can only improve it partially. This article proposes a brand-new oscillator structure leveraging a transformer-based series tank, which can tolerate larger currents, generate greater oscillation amplitudes, and achieve significant PN suppression. A general active circuit for series-resonance (SR) is analyzed. The proposed series tank provides adjustable low input impedance, is well-suited for high-frequency operation, and suppresses parasitic modes. With the folded transformer, the layout implementation is simplified. An SR voltage-controlled oscillator (VCO) prototype is designed and fabricated using a 65-nm CMOS process. It achieves a measured PN of $-$ 132.1 dBc/Hz at a 1-MHz offset and a corresponding figure of merit (FoM) of 187.4 dBc/Hz at a 10.65-GHz carrier frequency. The SR VCO is applied to a phase-locked loop (PLL), which achieves 33.7 fs of jitter with a 100-MHz reference clock, significantly reducing the demands on the reference path.
- 5 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 60 (2) , 529-542
A Transformer-Based Series-Resonance CMOS VCO
The LC parallel tank is widely used in oscillators, and its noise optimization techniques are relatively mature. However, there has always been a bottleneck in phase noise (PN) performance, and the multi-core technique can only improve it partially. This article proposes a brand-new oscillator structure leveraging a transformer-based series tank, which can tolerate larger currents, generate greater oscillation amplitudes, and achieve significant PN suppression. A general active circuit for series-resonance (SR) is analyzed. The proposed series tank provides adjustable low input impedance, is well-suited for high-frequency operation, and suppresses parasitic modes. With the folded transformer, the layout implementation is simplified. An SR voltage-controlled oscillator (VCO) prototype is designed and fabricated using a 65-nm CMOS process. It achieves a measured PN of $-$ 132.1 dBc/Hz at a 1-MHz offset and a corresponding figure of merit (FoM) of 187.4 dBc/Hz at a 10.65-GHz carrier frequency. The SR VCO is applied to a phase-locked loop (PLL), which achieves 33.7 fs of jitter with a 100-MHz reference clock, significantly reducing the demands on the reference path.
- 11 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (7) , 1981-1994
A Multireference PLL: Theory and Implementation
The limitation of reference phase noise (PN) causes problems for the very low-jitter phase-locked loops (PLLs), which is increasingly critical and may be an impediment toward 10 fs jitter. This article presents a multireference PLL (MRPLL) architecture featuring the ability to reduce reference PN by using more reference clocks. The architecture evolution, noise model analysis, and circuit design considerations are presented. Theoretically, the major contributor of reference PN is the reference buffer, including the buffer inside a packaged crystal oscillator (XO) and the buffer on-chip. Increasing the reference frequency can significantly reduce the PN of the reference buffer. The prototype of the MRPLL is implemented in a 65-nm CMOS process and achieves 16.1 fs jitter.
- 11 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (7) , 1981-1994
A Multireference PLL: Theory and Implementation
The limitation of reference phase noise (PN) causes problems for the very low-jitter phase-locked loops (PLLs), which is increasingly critical and may be an impediment toward 10 fs jitter. This article presents a multireference PLL (MRPLL) architecture featuring the ability to reduce reference PN by using more reference clocks. The architecture evolution, noise model analysis, and circuit design considerations are presented. Theoretically, the major contributor of reference PN is the reference buffer, including the buffer inside a packaged crystal oscillator (XO) and the buffer on-chip. Increasing the reference frequency can significantly reduce the PN of the reference buffer. The prototype of the MRPLL is implemented in a 65-nm CMOS process and achieves 16.1 fs jitter.
- 29 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (8) , 2441-2454
An Enhanced Class-F Dual-Core VCO With Common-Mode-Noise Self-Cancellation and Isolation Technique
In this article, an enhanced class-F voltage-controlled oscillator (VCO) with common-mode-noise self-cancellation (CM-NC) and common-mode-noise isolation (CM-NI) technique is proposed. With the proposed CM-NC technique, the common-mode-noise current of the drain coil and that of the nearby source coil are in the opposite direction. Therefore, the magnetic fields generated by the two coils cancel each other, which reduces the noise injected into the VCO from power supply and the ground node. Moreover, the principle of decoupling between the two inductors is also employed to eliminate the influence of the common-mode tail inductor on the differential mode. By winding the gate coil into a double-turn structure, the coupling noise from the drain inductor to the gate is opposite to the induced current of the gate coil, thereby cutting off the noise coupling path from the drain to the gate. Thanks to the dual-core 8-shaped inductor structure, the phase noise (PN) is improved without increasing the area, compared with existing methods using separated and dedicated tail filtering inductors. The VCO is fabricated in a 65-nm complementary metal–oxide–semiconductor (CMOS) technology. The measured tuning range is 21.7% from 11.5 to 14.3 GHz. The PN and figure of merit (FoM) at 1-MHz offset are −119.2 and 192.8 dBc/Hz, respectively. The power consumption across the frequency tuning range is 5.6–10 mW. The core area is 0.065 mm2 and the total area is 0.26 mm2.
- 29 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (8) , 2441-2454
An Enhanced Class-F Dual-Core VCO With Common-Mode-Noise Self-Cancellation and Isolation Technique
In this article, an enhanced class-F voltage-controlled oscillator (VCO) with common-mode-noise self-cancellation (CM-NC) and common-mode-noise isolation (CM-NI) technique is proposed. With the proposed CM-NC technique, the common-mode-noise current of the drain coil and that of the nearby source coil are in the opposite direction. Therefore, the magnetic fields generated by the two coils cancel each other, which reduces the noise injected into the VCO from power supply and the ground node. Moreover, the principle of decoupling between the two inductors is also employed to eliminate the influence of the common-mode tail inductor on the differential mode. By winding the gate coil into a double-turn structure, the coupling noise from the drain inductor to the gate is opposite to the induced current of the gate coil, thereby cutting off the noise coupling path from the drain to the gate. Thanks to the dual-core 8-shaped inductor structure, the phase noise (PN) is improved without increasing the area, compared with existing methods using separated and dedicated tail filtering inductors. The VCO is fabricated in a 65-nm complementary metal–oxide–semiconductor (CMOS) technology. The measured tuning range is 21.7% from 11.5 to 14.3 GHz. The PN and figure of merit (FoM) at 1-MHz offset are −119.2 and 192.8 dBc/Hz, respectively. The power consumption across the frequency tuning range is 5.6–10 mW. The core area is 0.065 mm2 and the total area is 0.26 mm2.