Jian Zou
Research Subjects
Jian Zou has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Hui Li
Harbin Engineering University
5 shared publications - Lin Lu
School of Naval Architecture & Ocean Engineering, Jiangsu University of Science and Technology, Zhenjiang, Jiangsu 212001, P. R. China
5 shared publications - Ruixiang Liu
Harbin Engn Univ, Coll Shipbldg Engn, Harbin 150001, Peoples R China
5 shared publications Hui Li
4 shared publicationsHaibin Zhang
3 shared publicationsBaoli Deng
2 shared publications
Latest Publications
- Open Access
- 24 October 2026
- Published by Elsevier in SSRN Electronic Journal
SPH investigation of flow evolution beneath a trimaran wet-deck with and without main hull emergence
A trimaran travelling in waves may experience partial main-hull emergence, generating distinct pre-impact flow fields before side-hull water contact. This work develops a smoothed particle hydrodynamics (SPH) model for trimaran section water entry using DualSPHysics, validated by convergence analysis and experimental data. Two cases, Model-O and Model-M, represent different main-hull emergence states. Using kinetic energy, cavity area and free-surface evolution, we investigate how emergence state and impact velocity affect wet-deck gap flow. For Model-O, fluid propagates laterally toward side hulls before forming a sustained vertical jet. In Model-M, lateral and vertical kinetic energy grow simultaneously in early impact and decay rapidly; its jet rises, expands and collapses onto the free surface. When side hulls immerse, Model-O’s pre-formed jet cooperates with local fluid uplift to accelerate gap filling, yielding a substantially higher cavity contraction rate than Model-M. Impact velocity weakly influences Model-O’s normalised flow field, while it accelerates cavity shrinkage and energy dissipation in Model-M without altering primary flow structures. We conclude that main-hull emergence dominates cavity evolution by setting pre-impact flow conditions, while impact velocity modulates flow magnitude and transition processes. These findings support wet-deck flow assessment and the design of main–side hull layouts and wet-deck clearance.
- 24 October 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessSPH investigation of flow evolution beneath a trimaran wet-deck with and without main hull emergence
A trimaran travelling in waves may experience partial main-hull emergence, generating distinct pre-impact flow fields before side-hull water contact. This work develops a smoothed particle hydrodynamics (SPH) model for trimaran section water entry using DualSPHysics, validated by convergence analysis and experimental data. Two cases, Model-O and Model-M, represent different main-hull emergence states. Using kinetic energy, cavity area and free-surface evolution, we investigate how emergence state and impact velocity affect wet-deck gap flow. For Model-O, fluid propagates laterally toward side hulls before forming a sustained vertical jet. In Model-M, lateral and vertical kinetic energy grow simultaneously in early impact and decay rapidly; its jet rises, expands and collapses onto the free surface. When side hulls immerse, Model-O’s pre-formed jet cooperates with local fluid uplift to accelerate gap filling, yielding a substantially higher cavity contraction rate than Model-M. Impact velocity weakly influences Model-O’s normalised flow field, while it accelerates cavity shrinkage and energy dissipation in Model-M without altering primary flow structures. We conclude that main-hull emergence dominates cavity evolution by setting pre-impact flow conditions, while impact velocity modulates flow magnitude and transition processes. These findings support wet-deck flow assessment and the design of main–side hull layouts and wet-deck clearance.
- 4 September 2026
- Published by Elsevier in Ocean Engineering
- Vol. 367
Numerical investigation on the whipping responses of a 6750 TEU container ship in focused waves
- 4 September 2026
- Published by Elsevier in Ocean Engineering
- Vol. 367
Numerical investigation on the whipping responses of a 6750 TEU container ship in focused waves
- Open Access
- 5 June 2026
- Published by Elsevier in SSRN Electronic Journal
Numerical investigation on the whipping responses of a 6750 TEU container ship in focused waves
Focused waves are characterized by large wave steepness and transient energy concentration, which may induce pronounced ship-motion responses and severe slamming events. Consequently, the high-frequency elastic vibrations excited by slamming events significantly increase the global loads, and thus cannot be neglected in safety assessments. To accurately simulate the slamming process and predict the whipping responses, a two-way fluid-structure interaction (FSI) method coupling computational fluid dynamics (CFD) and finite element method (FEM) was employed. The coupled algorithm was validated against experimental data, showing favorable agreement in both the low-frequency wave-induced responses and the high-frequency components excited by slamming. Subsequently, numerical simulations in focused waves were conducted to systematically investigate the ship responses under two different wave focal positions. Results demonstrate that the CFD-FEM coupled method can reasonably describe the motion responses in focused waves, capture the transient slamming loads, and predict the global load responses comprising both low-frequency and high-frequency components. The results further indicate that the wave focal position affects the wave–ship encounter process, thereby altering the timing and intensity of the hydroelastic responses. Bow re-entry slamming excites high-frequency whipping components, which are superimposed on the wave-frequency loads and contribute to transient amplification of the global vertical bending moment
- 5 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessNumerical investigation on the whipping responses of a 6750 TEU container ship in focused waves
Focused waves are characterized by large wave steepness and transient energy concentration, which may induce pronounced ship-motion responses and severe slamming events. Consequently, the high-frequency elastic vibrations excited by slamming events significantly increase the global loads, and thus cannot be neglected in safety assessments. To accurately simulate the slamming process and predict the whipping responses, a two-way fluid-structure interaction (FSI) method coupling computational fluid dynamics (CFD) and finite element method (FEM) was employed. The coupled algorithm was validated against experimental data, showing favorable agreement in both the low-frequency wave-induced responses and the high-frequency components excited by slamming. Subsequently, numerical simulations in focused waves were conducted to systematically investigate the ship responses under two different wave focal positions. Results demonstrate that the CFD-FEM coupled method can reasonably describe the motion responses in focused waves, capture the transient slamming loads, and predict the global load responses comprising both low-frequency and high-frequency components. The results further indicate that the wave focal position affects the wave–ship encounter process, thereby altering the timing and intensity of the hydroelastic responses. Bow re-entry slamming excites high-frequency whipping components, which are superimposed on the wave-frequency loads and contribute to transient amplification of the global vertical bending moment
- Open Access
- 15 May 2026
- Published by Elsevier in SSRN Electronic Journal
Experimental investigation on the slamming loads of a rigid cylinder
This paper investigates the hydrodynamic characteristics of a two-dimensional rigid cylinder during water entry via a series of drop tests. Due to the high-frequency and highly transient features of slamming pressure, a reasonable response measurement and analysis method is proposed by conducting modal analysis and performing comparative verification of sensors with different working principles. On this basis, a comprehensive dataset of slamming dynamics and kinematics is acquired, and data analysis verifies the high repeatability of the experimental results. The experimental results show that the dispersion of slamming pressure peaks at the cylinder bottom is significantly greater than that at other positions. One way ANOVA shows a significant difference in pressure dispersion among different deadrise angle groups (p < 0.01)**. In contrast, no significant difference is observed under different impact velocities or sensor flatness conditions. Combined with CFD numerical simulations, air cushioning effect is observed within the 0~5 deg at the model bottom. The high consistency between numerical simulations and experimental data validates the effectiveness of the proposed analysis framework. This work improves the experimental techniques for slamming load evaluation, and provides a solid physical and numerical foundation for the water entry analysis of curved marine structures.
- 15 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessExperimental investigation on the slamming loads of a rigid cylinder
This paper investigates the hydrodynamic characteristics of a two-dimensional rigid cylinder during water entry via a series of drop tests. Due to the high-frequency and highly transient features of slamming pressure, a reasonable response measurement and analysis method is proposed by conducting modal analysis and performing comparative verification of sensors with different working principles. On this basis, a comprehensive dataset of slamming dynamics and kinematics is acquired, and data analysis verifies the high repeatability of the experimental results. The experimental results show that the dispersion of slamming pressure peaks at the cylinder bottom is significantly greater than that at other positions. One way ANOVA shows a significant difference in pressure dispersion among different deadrise angle groups (p < 0.01)**. In contrast, no significant difference is observed under different impact velocities or sensor flatness conditions. Combined with CFD numerical simulations, air cushioning effect is observed within the 0~5 deg at the model bottom. The high consistency between numerical simulations and experimental data validates the effectiveness of the proposed analysis framework. This work improves the experimental techniques for slamming load evaluation, and provides a solid physical and numerical foundation for the water entry analysis of curved marine structures.
- 3 February 2026
- Published by Elsevier in Ocean Engineering
- Vol. 351
Study on water entry of curved elastic wedge using fully nonlinear boundary element method
- 3 February 2026
- Published by Elsevier in Ocean Engineering
- Vol. 351
Study on water entry of curved elastic wedge using fully nonlinear boundary element method
- 6 April 2025
- Published by Elsevier in Ocean Engineering
- Vol. 329
Numerical study on whipping response in irregular waves with asymmetric slamming for ultra large container ships
- 6 April 2025
- Published by Elsevier in Ocean Engineering
- Vol. 329
Numerical study on whipping response in irregular waves with asymmetric slamming for ultra large container ships
- Open Access
- 1 March 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (3)
Investigating the entry of symmetric/asymmetric elastic wedge into water
Understanding the impact of fluid–structure interaction during the entry of a marine vessel into water is crucial for its design. While numerous models have been proposed to investigate the penetration of symmetric elastic wedges into water, in this study, we propose a numerical model that combines the fully nonlinear boundary element method with a mode superposition method to analyze the penetration of symmetric and asymmetric elastic wedges into water. We derive the boundary conditions of the acceleration potential within the flow field for the problem of fluid–structure interaction and use auxiliary functions to decompose the acceleration potential and extract the instantaneous added mass. Following this, the differential equations of the modes of rigid motion and elastic deformation of the body are established and solved. This approach enables the simultaneous solution of the motion and vibrations of the wedge as well as the hydrodynamic pressure. The proposed model also accounts for flow separation while the wedge is submerged, thereby prolonging the simulation. We confirmed the validity of the model through comprehensive examinations based on semi-analytical, computational, and experimental data on the problem of the entry of a symmetric body into water. We then extended our study to encompass the free-falling entry of an asymmetric elastic wedge into water. The results revealed notable discrepancies in the evolution of deformation and jet flow between the right and left boundaries during the entry of the wedge into water.
- 1 March 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (3)
Open AccessInvestigating the entry of symmetric/asymmetric elastic wedge into water
Understanding the impact of fluid–structure interaction during the entry of a marine vessel into water is crucial for its design. While numerous models have been proposed to investigate the penetration of symmetric elastic wedges into water, in this study, we propose a numerical model that combines the fully nonlinear boundary element method with a mode superposition method to analyze the penetration of symmetric and asymmetric elastic wedges into water. We derive the boundary conditions of the acceleration potential within the flow field for the problem of fluid–structure interaction and use auxiliary functions to decompose the acceleration potential and extract the instantaneous added mass. Following this, the differential equations of the modes of rigid motion and elastic deformation of the body are established and solved. This approach enables the simultaneous solution of the motion and vibrations of the wedge as well as the hydrodynamic pressure. The proposed model also accounts for flow separation while the wedge is submerged, thereby prolonging the simulation. We confirmed the validity of the model through comprehensive examinations based on semi-analytical, computational, and experimental data on the problem of the entry of a symmetric body into water. We then extended our study to encompass the free-falling entry of an asymmetric elastic wedge into water. The results revealed notable discrepancies in the evolution of deformation and jet flow between the right and left boundaries during the entry of the wedge into water.
- 21 September 2023
- Published by Elsevier in Ocean Engineering
- Vol. 287, 115830
Numerical method for whipping response of ultra large container ships under asymmetric slamming in regular waves
- 21 September 2023
- Published by Elsevier in Ocean Engineering
- Vol. 287, 115830
Numerical method for whipping response of ultra large container ships under asymmetric slamming in regular waves