CGChristopher Grandy

Christopher Grandy

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Christopher Grandy has a total of 6 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Design and Analysis of a Mutual Inductance Level Sensor for Liquid Metals

    by Edward Kent, Matthew Weathered, Christopher Grandy, Heng Ban

    This article describes the design and analysis of an electromagnetic level sensor for use in high-temperature liquid metal systems. The mutual inductance level sensor (MILS) described in this work was fabricated using two single-conductor mineral insulated cables wrapped in a bifilar fashion around a stainless steel tube core and was housed in an isolating thimble that preserved the pressure boundary of the test vessel. Two sensor variations were fabricated that differ only in active length, 1016 mm and 1778 mm. Experimental data were collected using the 1016 mm sensor (MILS-MKII-040) that demonstrated a sensitivity of 9.2 μV/mm in a room-temperature testing stand that used solid aluminum as a surrogate for liquid metal. Experimental data were collected using the 1778 mm sensor (MILS-MKII-070) that demonstrated a sensitivity of 6.9 μV/mm in the high-temperature (300°C) liquid sodium environment at the Mechanisms Engineering Test Loop of Argonne National Laboratory. The sensor performance was found to be repeatable over the course of several months, with roughly ±1% deviation from nominal output. Finite element models were developed in COMSOL Multiphysics that fully describe each test setup, and the models were validated using experimental data. The validated COMSOL models were used to perform an array of analyses that examined the performance of the sensor in differing environments. Maximizing the coil diameter inside the isolating thimble was found to maximize the signal and sensitivity of the sensor. An optimal operating frequency was found near 1000 Hz using both experimental data and COMSOL. The influence of a metallic thimble surrounding the sensor and a metallic sensor core was quantified and found to be negligible at the optimal operating frequency. The sensitivity of the sensor was quantified when monitoring the level of additional liquid metals. These include lead, lead bismuth eutectic (LBE), sodium potassium alloy (NaK), and lithium (in addition to sodium). The sensitivities were quantified using liquid metal properties at 350°C and 650°C. The geometry of the test stand model, all material properties used in the model, and the results are presented in a manner that the reader can replicate the model and perform additional analyses.


  • Design Optimization and Measurement Uncertainty of an Electromagnetic Level Sensor for Liquid Metal Reactors

    by Edward Kent, Duane DiCenzo, Brady Cameron, Heng Ban, Christopher Grandy

    This paper describes the design and operation of a prototype mutual inductance level sensor (MILS) and the development and validation of a finite-element analysis (FEA) model describing its behavior. The MILS was designed for use in liquid sodium up to temperatures of 650°C in the Mechanisms Engineering Test Loop (METL) at Argonne National Laboratory (ANL). Preliminary testing was performed in a room temperature test stand with aluminum acting as an analog for the sodium to better understand sensor performance and provide accurate code validation data. This experimental data, along with material properties found in literature, were used to validate a finite-element analysis model in ANSYS Maxwell. The validated ANSYS Maxwell model was used to examine the performance of the MILS in various environments and under various operating conditions. Simulations suggest the following: The MILS will perform adequately in liquid sodium and liquid lead at temperatures up to 650°C. The temperature dependence of electrical conductivity imposes a temperature dependence on the sensor that requires proper compensation. The MILS signal sensitivity is maximized when mutual inductance between sensor coils is maximized, and sensor geometry should be selected to account for this factor. The operating frequency of the MILS can be optimized and is dependent on process fluid material, operating temperature, and materials/geometry of sensor system. And finally the use of a stainless steel isolating thimble does not adversely affect the sensor signal. The primary sources of error for this MILS system are the accuracy of the calibration standard against which the sensor is calibrated, and the temperature dependence of the sensor. This work contains all the necessary details to recreate the FEA model and results. This model can be used to optimize the performance of a MILS in any operating environment to read any electrically conductive working fluid.


  • Open Access

    Financial Integration in Antebellum America: Strengthening Bodenhorn's Results

    by Sumner J. La Croix, Christopher Grandy

    In a recent article in this Journal, Howard Bodenhorn made a remarkable suggestion: “Antebellum financial markets may have outperformed those of the post–Civil War period.” According to Bodenhorn, antebellum capital markets displayed notable integration, as indicated by movements in short-term (60–day) interest rate data for important commercial centers east of the Mississippi. When considered in light of Lance Davis's work, suggesting poor integration of credit markets immediately after the Civil War and only gradual integration thereafter, we believe economic historians will find Bodenhorn's hypothesis provocative—even startling. We found the hypothesis so suggestive that we attempted to replicate Bodenhorn's analysis—a process that generated both “bad news” and “good news.” The “bad news” is that we believe the evidence Bodenhorn provided for his hypothesis is weak or irrelevant. The “good news” is that the data Bodenhorn generated support the integration hypothesis more strongly than even Bodenhorn suggested.