Qingqing Lin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Qingqing Lin has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Jun Xu
School of Information Science and Engineering, State Key Laboratory of Millimeter Waves, Southeast University, Nanjing, China
4 shared publications - Kai Chen
State Key Laboratory of Millimeter Waves, School of Information Science and Engineering, Southeast University, Nanjing, China
4 shared publications - Wei Hong
Southeast University
4 shared publications - Wei Li
State Key Laboratory of Millimeter Waves, School of Information Science and Engineering, Southeast University, Nanjing, China
3 shared publications - Sai Ma
State Key Laboratory of Millimeter Waves, School of Information Science and Engineering, Southeast University, Nanjing, China
2 shared publications - Yuanwei Zhu
State Key Laboratory of Millimeter Waves, Southeast University, Nanjing, China
2 shared publications
Latest Publications
- 28 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (11) , 4217-4221
A Multibeam Antenna Using Compact Low-Profile Wideband 4 × 8 Butler Matrix Incorporating Diverse Transmission Lines
This letter introduces a multibeam antenna that employs a compact, wideband 4 × 8 Butler matrix (BM), incorporating diverse transmission lines such as substrate-integrated coaxial line (SICL), grounded coplanar waveguide (GCPW), and substrate-integrated waveguide (SIW) without increasing the number of dielectric substrate layers. This approach enhances the topology of the 4 × 8 BM. By replacing crossovers with spatially crossed GCPW transmission lines at the top and bottom layers, the configuration of the network is greatly simplified, facilitating the miniaturization of the BM. Furthermore, an ideal 180-degree phase-shifting scheme is proposed that not only addresses the issue of signal lines not being on the same layer but also achieves 180-degree phase shifting across the wide operating band by transitioning the GCPWs on the top and bottom layers to the SIW cavity. Finally, eight magneto-electric dipoles (ME-dipoles) were connected to the output ports of the 4 × 8 BM forming the proposed multibeam antenna. A prototype of this multibeam antenna was fabricated and measured, it is evident that a compact structure and an impressive operating bandwidth of 20.56% (24-29.5 GHz) has been achieved. The measured data confirms its potential as a promising candidate for B5G/6G millimeter-wave communications.
- 28 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (11) , 4217-4221
A Multibeam Antenna Using Compact Low-Profile Wideband 4 × 8 Butler Matrix Incorporating Diverse Transmission Lines
This letter introduces a multibeam antenna that employs a compact, wideband 4 × 8 Butler matrix (BM), incorporating diverse transmission lines such as substrate-integrated coaxial line (SICL), grounded coplanar waveguide (GCPW), and substrate-integrated waveguide (SIW) without increasing the number of dielectric substrate layers. This approach enhances the topology of the 4 × 8 BM. By replacing crossovers with spatially crossed GCPW transmission lines at the top and bottom layers, the configuration of the network is greatly simplified, facilitating the miniaturization of the BM. Furthermore, an ideal 180-degree phase-shifting scheme is proposed that not only addresses the issue of signal lines not being on the same layer but also achieves 180-degree phase shifting across the wide operating band by transitioning the GCPWs on the top and bottom layers to the SIW cavity. Finally, eight magneto-electric dipoles (ME-dipoles) were connected to the output ports of the 4 × 8 BM forming the proposed multibeam antenna. A prototype of this multibeam antenna was fabricated and measured, it is evident that a compact structure and an impressive operating bandwidth of 20.56% (24-29.5 GHz) has been achieved. The measured data confirms its potential as a promising candidate for B5G/6G millimeter-wave communications.
- Open Access
- 7 May 2024
- Published by Elsevier in Engineering
- Vol. 41, 35-50
A Single-Board Integrated Millimeter-Wave Asymmetric Full-Digital Beamforming Array for B5G/6G Applications
- 7 May 2024
- Published by Elsevier in Engineering
- Vol. 41, 35-50
Open AccessA Single-Board Integrated Millimeter-Wave Asymmetric Full-Digital Beamforming Array for B5G/6G Applications
- 22 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (8) , 3730-3734
A Broadband Low-Loss SICL to Ridge Waveguide Transition for Millimeter-Wave Applications
In this article, a millimeter-wave (mmWave) broadband low-loss substrate integrated coaxial line (SICL) to ridge waveguide (RIWG) transition is proposed. The transition realizes the conversion from the TEM mode in SICL to the TE10 mode in RIWG through a T-shaped patch. To achieve broadband and low loss characteristics, a multi-section impedance transformer is employed to enhance the matching performance at low frequencies, and metalized via array matching structures are used to improve the matching performance at high frequencies. For verification, a back-to-back transition prototype was designed and fabricatedC and the measured results agree well with the simulated ones. The measured results indicate that the transition structure has a wide operating bandwidth of 71 covering 23 GHz to 48.35 GHz, and the insertion loss is lower than 0.35 dB within the entire operating band. The merits of the proposed transition, e.g., compact size and stable performance, make it promising for advanced millimeter-wave circuits and systems.
- 22 February 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 71 (8) , 3730-3734
A Broadband Low-Loss SICL to Ridge Waveguide Transition for Millimeter-Wave Applications
In this article, a millimeter-wave (mmWave) broadband low-loss substrate integrated coaxial line (SICL) to ridge waveguide (RIWG) transition is proposed. The transition realizes the conversion from the TEM mode in SICL to the TE10 mode in RIWG through a T-shaped patch. To achieve broadband and low loss characteristics, a multi-section impedance transformer is employed to enhance the matching performance at low frequencies, and metalized via array matching structures are used to improve the matching performance at high frequencies. For verification, a back-to-back transition prototype was designed and fabricatedC and the measured results agree well with the simulated ones. The measured results indicate that the transition structure has a wide operating bandwidth of 71 covering 23 GHz to 48.35 GHz, and the insertion loss is lower than 0.35 dB within the entire operating band. The merits of the proposed transition, e.g., compact size and stable performance, make it promising for advanced millimeter-wave circuits and systems.
- 12 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 73 (3) , 3536-3550
Single-Layer Wideband Tilted Beam Phased Array Antenna for Millimeter-Wave Vehicle Communications
In this article, a wideband tilted beam phased array antenna is proposed for millimeter-wave (mmWave) vehicle communications. The developed antenna element obtains a measured | S 11 |<-10 dB impedance bandwidth of 49.4% (23.3-38.6 GHz) by loading two monopoles ahead of the open-end aperture of a single-layer substrate integrated waveguide (SIW) with an etched transverse slot, thus, covering multiple allocated mmWave bands of the fifth-generation (5G). Meanwhile, the loaded two monopole structures also introduce a broadside radiation aperture, which combines with the original end-fire radiation aperture forming a stable 45° tilted beam pattern within the frequency band. Prototype of a 1 × 4 phased array is fabricated and measured, and the beam scanning performance of the array is verified using a multi-channel beamformer, with a 3 dB beam scanning range exceeds 86° at 27 GHz. The proposed antenna boasts the characteristics of wideband, a stable tilted beam, and good beam scanning performance, rendering it a promising candidate for mmWave vehicular communications. Additionally, a hybrid 2D beam scanning is realized by combining a cylindrical Luneburg lens antenna with the 1×4 phased array to fully exploit the advantages of both techniques. Experimental validation has also been carried out to confirm the feasibility of the proposed hybrid 2D beam scanning scheme.
- 12 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Vehicular Technology
- Vol. 73 (3) , 3536-3550
Single-Layer Wideband Tilted Beam Phased Array Antenna for Millimeter-Wave Vehicle Communications
In this article, a wideband tilted beam phased array antenna is proposed for millimeter-wave (mmWave) vehicle communications. The developed antenna element obtains a measured | S 11 |<-10 dB impedance bandwidth of 49.4% (23.3-38.6 GHz) by loading two monopoles ahead of the open-end aperture of a single-layer substrate integrated waveguide (SIW) with an etched transverse slot, thus, covering multiple allocated mmWave bands of the fifth-generation (5G). Meanwhile, the loaded two monopole structures also introduce a broadside radiation aperture, which combines with the original end-fire radiation aperture forming a stable 45° tilted beam pattern within the frequency band. Prototype of a 1 × 4 phased array is fabricated and measured, and the beam scanning performance of the array is verified using a multi-channel beamformer, with a 3 dB beam scanning range exceeds 86° at 27 GHz. The proposed antenna boasts the characteristics of wideband, a stable tilted beam, and good beam scanning performance, rendering it a promising candidate for mmWave vehicular communications. Additionally, a hybrid 2D beam scanning is realized by combining a cylindrical Luneburg lens antenna with the 1×4 phased array to fully exploit the advantages of both techniques. Experimental validation has also been carried out to confirm the feasibility of the proposed hybrid 2D beam scanning scheme.