Faten Nasri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Faten Nasri has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Mohamed Kharrat
Laboratory of Electromechanical Systems, National School of Engineers of Sfax, University of Sfax, Sfax 3038, Tunisia
5 shared publications - António Bastos Pereira
TEMA—Centre for Mechanical Technology and Automation, Department of Mechanical Engineering, University of Aveiro, Campus de Santiago, 3810-193 Aveiro, Portugal
3 shared publications - Dorra Trabelsi
University of Sfax
3 shared publications - Florence Vacandio
Aix-Marseille University, CNRS, MADIREL UMR 7246, Marseille cedex 20, France
3 shared publications - Marielle Eyraud
UMR 7246, Divided Materials, Interfaces, Reactivity, Electrochemistry (MADIREL), CNRS, Aix Marseille University, 13013 Marseille, France
3 shared publications - César Cardoso
Rodi Industries, S.A., 3801-551 Aveiro, Portugal
2 shared publications
Latest Publications
- Open Access
- 26 February 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (3) , 100
On the Microstructural and Tribological Investigations of WC-12Co/NiCrFeSiAlBC HVOF Cermet Coatings: Effects of WC-12Co Fraction
Previous research indicates that WC-12Co contents above 60 wt.% in feedstock powders for cermet coatings impair adhesion and wear resistance. This study characterizes NiCrFeSiAlBC coatings—unreinforced or reinforced with 65 wt.% or 85 wt.% WC-12Co—applied via high-velocity oxy-fuel (HVOF) spraying onto stainless steel substrates under controlled parameters. It quantifies the influence of high carbide volume fractions within the NiCrFeSiAlBC matrix on microstructure and tribomechanical performance. Microstructural analysis revealed uniformly distributed cermet layers featuring dissolved reinforcements and WC hard phase formation, with minimal W2C crystallization. Elevated WC-12Co incorporation promoted densification and reduced porosity. Vickers microhardness tests (HV 0.3) demonstrated increased hardness upon WC-12Co addition, attributable to finer particle sizes, lower porosity, and the presence of WC phases alongside crystallographic refinements. Under dry reciprocating sliding conditions, friction coefficients and wear volumes decreased markedly. Consequently, the coating with 85 wt.% WC exhibited the best mechanical and tribological properties.
- 26 February 2026
- Published by MDPI AG in Lubricants
- Vol. 14 (3) , 100
Open AccessOn the Microstructural and Tribological Investigations of WC-12Co/NiCrFeSiAlBC HVOF Cermet Coatings: Effects of WC-12Co Fraction
Previous research indicates that WC-12Co contents above 60 wt.% in feedstock powders for cermet coatings impair adhesion and wear resistance. This study characterizes NiCrFeSiAlBC coatings—unreinforced or reinforced with 65 wt.% or 85 wt.% WC-12Co—applied via high-velocity oxy-fuel (HVOF) spraying onto stainless steel substrates under controlled parameters. It quantifies the influence of high carbide volume fractions within the NiCrFeSiAlBC matrix on microstructure and tribomechanical performance. Microstructural analysis revealed uniformly distributed cermet layers featuring dissolved reinforcements and WC hard phase formation, with minimal W2C crystallization. Elevated WC-12Co incorporation promoted densification and reduced porosity. Vickers microhardness tests (HV 0.3) demonstrated increased hardness upon WC-12Co addition, attributable to finer particle sizes, lower porosity, and the presence of WC phases alongside crystallographic refinements. Under dry reciprocating sliding conditions, friction coefficients and wear volumes decreased markedly. Consequently, the coating with 85 wt.% WC exhibited the best mechanical and tribological properties.
- Open Access
- 15 May 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (5) , 246
Electrodeposited Composite Coatings Based on Ni Matrix Filled with Solid Lubricants: Impact of Processing Parameters on Tribological Properties and Scratch Resistance
Electrodeposited composite coatings are widely studied for their potential to improve surface properties such as wear resistance and friction reduction. This study investigates the effect of electrodeposition parameters on the structure, morphology, and tribological performance of three coatings: pure nickel (Ni), Ni–graphite (Ni-G), and Ni–MoS2 (Ni-MoS2). Three deposition conditions were selected based on a review of key electrochemical parameters commonly used in the literature. The coatings were analyzed in terms of morphological characteristics, friction and wear resistance. The findings reveal that higher current densities led to increased friction and wear in Ni coatings, while lower pH values promoted finer crystallite sizes and improved tribological behavior. Ni-G coatings exhibited larger cluster formations with reduced friction and wear, especially at low pH, whereas Ni-MoS2 coatings developed a stable cauliflower-like morphology at pH 2, but showed reduced adhesion and structural integrity at higher pH levels. Scratch resistance tests performed under optimal deposition conditions showed that Ni-G coatings provided the highest resistance to mechanical damage, while Ni-MoS2 coatings were more susceptible to microcracking and adhesion failure. These results underscore the importance of optimizing deposition parameters to tailor the microstructure and functional properties of composite coatings for enhanced tribological and mechanical performance.
- 15 May 2025
- Published by MDPI AG in Journal of Composites Science
- Vol. 9 (5) , 246
Open AccessElectrodeposited Composite Coatings Based on Ni Matrix Filled with Solid Lubricants: Impact of Processing Parameters on Tribological Properties and Scratch Resistance
Electrodeposited composite coatings are widely studied for their potential to improve surface properties such as wear resistance and friction reduction. This study investigates the effect of electrodeposition parameters on the structure, morphology, and tribological performance of three coatings: pure nickel (Ni), Ni–graphite (Ni-G), and Ni–MoS2 (Ni-MoS2). Three deposition conditions were selected based on a review of key electrochemical parameters commonly used in the literature. The coatings were analyzed in terms of morphological characteristics, friction and wear resistance. The findings reveal that higher current densities led to increased friction and wear in Ni coatings, while lower pH values promoted finer crystallite sizes and improved tribological behavior. Ni-G coatings exhibited larger cluster formations with reduced friction and wear, especially at low pH, whereas Ni-MoS2 coatings developed a stable cauliflower-like morphology at pH 2, but showed reduced adhesion and structural integrity at higher pH levels. Scratch resistance tests performed under optimal deposition conditions showed that Ni-G coatings provided the highest resistance to mechanical damage, while Ni-MoS2 coatings were more susceptible to microcracking and adhesion failure. These results underscore the importance of optimizing deposition parameters to tailor the microstructure and functional properties of composite coatings for enhanced tribological and mechanical performance.
- 13 May 2025
- Published by Springer Nature
- p. 604-612
Morphological Characterization of Zn-Co Coatings: Effect of Additive and Baths’ Parameters
- 13 May 2025
- Published by Springer Nature
- p. 604-612
Morphological Characterization of Zn-Co Coatings: Effect of Additive and Baths’ Parameters
- Open Access
- 7 April 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (4) , 167
Contribution of Zn–Co Alloys Coatings Study: Electrodeposition Methodology, Micromechanical Properties, and Tribological Behavior
: An overview of the literature reveals that electrodeposition baths significantly influence deposited coatings’ morphology and properties. The present study investigates a sulphate-based bath in terms of the additive, pH, and temperature for the electrodeposition of Zn–Co alloys onto mild steel, achieving a nanocrystalline structure. The obtained results of the cyclic voltametric and SEM analyses revealed that sodium allowed the enhancement of cobalt electrocrystallisation (22.6 wt%) to homogenize further layers’ structure. However, the adjustment of pH allowed for the obtention of deposits with a refined structure containing only 5 wt% cobalt. Although an increase in room temperature resulted in deposit coatings with the same cobalt content, it notably produced a smoother structure. Subsequently, Zn–Co coatings were compared to pure zinc layers in terms of micromechanical and tribological behaviour. The morphology shifted from hexagonal platelets to nodular structures with the incorporation of cobalt, leading to an increase in microhardness. The morphology transformation, coupled with micromechanical reinforcement, contributed to the mitigation of friction and the improvement of the wear resistance of zinc layers through cobalt alloying. In fact, this improvement enhances the performance of zinc-coated applications in automotive and aerospace industries, particularly for standard assembly components that require adequate resistance to wear and abrasion during handling and tightening.
- 7 April 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (4) , 167
Open AccessContribution of Zn–Co Alloys Coatings Study: Electrodeposition Methodology, Micromechanical Properties, and Tribological Behavior
: An overview of the literature reveals that electrodeposition baths significantly influence deposited coatings’ morphology and properties. The present study investigates a sulphate-based bath in terms of the additive, pH, and temperature for the electrodeposition of Zn–Co alloys onto mild steel, achieving a nanocrystalline structure. The obtained results of the cyclic voltametric and SEM analyses revealed that sodium allowed the enhancement of cobalt electrocrystallisation (22.6 wt%) to homogenize further layers’ structure. However, the adjustment of pH allowed for the obtention of deposits with a refined structure containing only 5 wt% cobalt. Although an increase in room temperature resulted in deposit coatings with the same cobalt content, it notably produced a smoother structure. Subsequently, Zn–Co coatings were compared to pure zinc layers in terms of micromechanical and tribological behaviour. The morphology shifted from hexagonal platelets to nodular structures with the incorporation of cobalt, leading to an increase in microhardness. The morphology transformation, coupled with micromechanical reinforcement, contributed to the mitigation of friction and the improvement of the wear resistance of zinc layers through cobalt alloying. In fact, this improvement enhances the performance of zinc-coated applications in automotive and aerospace industries, particularly for standard assembly components that require adequate resistance to wear and abrasion during handling and tightening.
- 24 March 2024
- Published by Springer Nature
- p. 241-248
Morphological and Structural Characterization of Zn-Ni Electrodeposited Coatings: Effect of Sulfate Bath Parameters
- 24 March 2024
- Published by Springer Nature
- p. 241-248
Morphological and Structural Characterization of Zn-Ni Electrodeposited Coatings: Effect of Sulfate Bath Parameters