Andrei Mitru
Andrei Mitru has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Adrian Savescu
INCDT COMOTI, Bucharest, Romania
1 shared publication- Augustin Semenescu
Faculty of Materials Science and Engineering, National University of Science and Technology Politehnica Bucharest, 313 Independentei Street, 060042 Bucharest, Romania
1 shared publication - Claudia Borzea
Romanian Research and Development Institute for Gas Turbines COMOTI, 061126 Bucharest, Romania
1 shared publication Claudia Savescu
Romanian Research and Development Institute for Gas Turbines COMOTI, Romania | Politehnica Bucharest, Romania
1 shared publication- Cristian Nechifor
Romanian Research and Development Institute for Gas Turbines COMOTI, Bucharest, Romania
1 shared publication - Daniel Comeagă
Faculty of Mechanical Engineering and Mechatronics, National University of Science and Technology POLITEHNICA Bucharest, 060042 Bucharest, Romania
1 shared publication
Latest Publications
- Open Access
- 25 March 2025
- Published by Editura Academiei Române in REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE
- Vol. 70 (1) , 97-102
DATA COMMUNICATION AND SOFTWARE DEVELOPMENT FOR THE AUTOMATION OF AN INDUSTRIAL PISTON COMPRESSOR
The work of data communication and developing software on the automation systems is related to 13 existing piston compressors located within the compressor station C144-M5 Bustuchin, Gorj, Romania. A project solution was applied to all 13 compressors and involves the communication of the parameter values of the compressors from the C144-M5 Bustuchin station to a local higher hierarchical system and a remote higher hierarchical system. The article presents the compressor automation system with a reliable architecture and a performing data communication network. The article mainly focuses on the developed software solution for the station operator panel, the compressor operator panels, and the station computer. In the second part of the article, the communication solutions for a complex data network with a higher local hierarchical system and a higher remote hierarchical system are presented from the point of view of the data server and the addresses assigned for each compressor parameter.
- 25 March 2025
- Published by Editura Academiei Române in REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE
- Vol. 70 (1) , 97-102
Open AccessDATA COMMUNICATION AND SOFTWARE DEVELOPMENT FOR THE AUTOMATION OF AN INDUSTRIAL PISTON COMPRESSOR
The work of data communication and developing software on the automation systems is related to 13 existing piston compressors located within the compressor station C144-M5 Bustuchin, Gorj, Romania. A project solution was applied to all 13 compressors and involves the communication of the parameter values of the compressors from the C144-M5 Bustuchin station to a local higher hierarchical system and a remote higher hierarchical system. The article presents the compressor automation system with a reliable architecture and a performing data communication network. The article mainly focuses on the developed software solution for the station operator panel, the compressor operator panels, and the station computer. In the second part of the article, the communication solutions for a complex data network with a higher local hierarchical system and a higher remote hierarchical system are presented from the point of view of the data server and the addresses assigned for each compressor parameter.
- Open Access
- 2 April 2024
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 14 (2) , 13449-13455
Thermal Potential of a Twin-Screw Compressor as Thermoelectric Energy Harvesting Source
This study evaluates the potential of a twin-screw compressor as a heat source to harness thermal energy. Thermoelectric generators are a feasible solution for microenergy harvesting from waste heat based on the Seebeck effect. Thermographic infrared images of the compressor were used to assess potential installation spots. The physical mounting of the thermoelectric modules must consider certain hindering aspects. At first, the compressor skid is subject to standards and authorizations for its components, leaving only a couple of spots for screw-mounted module installations. Another inconvenience is the bonds in any thermoelectric material causing them not to withstand lateral mechanical stress in other directions except the c-axis perpendicular to the layers. Therefore, vibration measurements have to be performed beforehand. Numerical simulations were conducted, relying on the acquired thermoelectric modules as well as on the temperature and vibration data measured on the compressor. The thermoelectric generators studied are part of a multisource piezoelectric and thermoelectric energy harvesting system under research and development.
- 2 April 2024
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 14 (2) , 13449-13455
Open AccessThermal Potential of a Twin-Screw Compressor as Thermoelectric Energy Harvesting Source
This study evaluates the potential of a twin-screw compressor as a heat source to harness thermal energy. Thermoelectric generators are a feasible solution for microenergy harvesting from waste heat based on the Seebeck effect. Thermographic infrared images of the compressor were used to assess potential installation spots. The physical mounting of the thermoelectric modules must consider certain hindering aspects. At first, the compressor skid is subject to standards and authorizations for its components, leaving only a couple of spots for screw-mounted module installations. Another inconvenience is the bonds in any thermoelectric material causing them not to withstand lateral mechanical stress in other directions except the c-axis perpendicular to the layers. Therefore, vibration measurements have to be performed beforehand. Numerical simulations were conducted, relying on the acquired thermoelectric modules as well as on the temperature and vibration data measured on the compressor. The thermoelectric generators studied are part of a multisource piezoelectric and thermoelectric energy harvesting system under research and development.
- Open Access
Study on the Weldability of Copper—304L Stainless Steel Dissimilar Joint Performed by Robotic Gas Tungsten Arc Welding
The welding process of dissimilar metals, with distinct chemical, physical, thermal, and structural properties, needs to be studied and treated with special attention. The main objectives of this research were to investigate the weldability of the dissimilar joint made between the 99.95% Cu pipe and the 304L stainless steel plate by robotic Gas Tungsten Arc Welding (GTAW), without filler metal and without preheating of materials, and to find the optimum welding regime. Based on repeated adjustments of the main process parameters—welding speed, oscillation frequency, pulse frequency, main welding current, pulse current, and decrease time of welding current at the process end—it was determined the optimum process and, further, it was possible to carry out joints free of cracks and porosity, with full penetration, proper compactness, and sealing properties, that ensure safety in operating conditions. The microstructure analysis revealed the fusion zone as a multi-element alloy with preponderant participation of Cu that has resulted from mixing the non-ferrous elements and iron. Globular Cu- or Fe-rich compounds were developed during welding, being detected by Scanning Electron Microscope (SEM). Moreover, the Energy Dispersive X-ray Analysis (EDAX) recorded the existence of a narrow double mixing zone formed at the interface between the fusion zone and the 304L stainless steel that contains about 66 wt.% Fe, 18 wt.% Cr, 8 wt.% Cu, and 4 wt.% Ni. Due to the formation of Fe-, Cr-, and Ni-rich compounds, a hardness increase up to 127 HV0.2 was noticed in the fusion zone, in comparison with the copper material, where the average measured microhardness was 82 HV0.2. The optimization of the robotic welding regime was carried out sequentially, by adjusting the parameters values, and, further, by analyzing the effects of welding on the geometry and on the appearance of the weld bead. Finally, employing the optimum welding regime—14 cm/min welding speed, 125 A main current, 100 A pulse current, 2.84 Hz oscillation frequency, and 5 Hz pulse frequency—appropriate dissimilar joints, without imperfections, were achieved.
Open AccessStudy on the Weldability of Copper—304L Stainless Steel Dissimilar Joint Performed by Robotic Gas Tungsten Arc Welding
The welding process of dissimilar metals, with distinct chemical, physical, thermal, and structural properties, needs to be studied and treated with special attention. The main objectives of this research were to investigate the weldability of the dissimilar joint made between the 99.95% Cu pipe and the 304L stainless steel plate by robotic Gas Tungsten Arc Welding (GTAW), without filler metal and without preheating of materials, and to find the optimum welding regime. Based on repeated adjustments of the main process parameters—welding speed, oscillation frequency, pulse frequency, main welding current, pulse current, and decrease time of welding current at the process end—it was determined the optimum process and, further, it was possible to carry out joints free of cracks and porosity, with full penetration, proper compactness, and sealing properties, that ensure safety in operating conditions. The microstructure analysis revealed the fusion zone as a multi-element alloy with preponderant participation of Cu that has resulted from mixing the non-ferrous elements and iron. Globular Cu- or Fe-rich compounds were developed during welding, being detected by Scanning Electron Microscope (SEM). Moreover, the Energy Dispersive X-ray Analysis (EDAX) recorded the existence of a narrow double mixing zone formed at the interface between the fusion zone and the 304L stainless steel that contains about 66 wt.% Fe, 18 wt.% Cr, 8 wt.% Cu, and 4 wt.% Ni. Due to the formation of Fe-, Cr-, and Ni-rich compounds, a hardness increase up to 127 HV0.2 was noticed in the fusion zone, in comparison with the copper material, where the average measured microhardness was 82 HV0.2. The optimization of the robotic welding regime was carried out sequentially, by adjusting the parameters values, and, further, by analyzing the effects of welding on the geometry and on the appearance of the weld bead. Finally, employing the optimum welding regime—14 cm/min welding speed, 125 A main current, 100 A pulse current, 2.84 Hz oscillation frequency, and 5 Hz pulse frequency—appropriate dissimilar joints, without imperfections, were achieved.
- 27 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Automation Control System for Naval Propulsion Retrofitting
Nowadays, automation systems for naval propulsion groups with gas turbines use programmable logic controllers for a precise and reliable control. The automation system is designed so as to be able to connect using signal cables to the transducers monitoring the engine’s parameters, via adapters, so that the command and regulation functions to be fully automatized. These signals are managed by means of the software program implemented in the PLC, and subsequent data acquisition. One of the important problems is the available resource of the propulsion group, until capital repair is required. The remaining lifetime depends on the operating regimes of the gas turbine engine. This problem is more pronounced in the propulsion groups equipping navy ships, where the dynamic regimes of gas turbine engines are much more demanding, and hence the pre-established operating limits may be exceeded. The automation configuration presented herein ensures the accurate computation and precise control of essential parameters for which the direct measurement is not possible using transducers. These parameters are the exhaust gas temperature, the power developed by the engine and implicitly the torque developed at propeller shaft.
- 27 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Automation Control System for Naval Propulsion Retrofitting
Nowadays, automation systems for naval propulsion groups with gas turbines use programmable logic controllers for a precise and reliable control. The automation system is designed so as to be able to connect using signal cables to the transducers monitoring the engine’s parameters, via adapters, so that the command and regulation functions to be fully automatized. These signals are managed by means of the software program implemented in the PLC, and subsequent data acquisition. One of the important problems is the available resource of the propulsion group, until capital repair is required. The remaining lifetime depends on the operating regimes of the gas turbine engine. This problem is more pronounced in the propulsion groups equipping navy ships, where the dynamic regimes of gas turbine engines are much more demanding, and hence the pre-established operating limits may be exceeded. The automation configuration presented herein ensures the accurate computation and precise control of essential parameters for which the direct measurement is not possible using transducers. These parameters are the exhaust gas temperature, the power developed by the engine and implicitly the torque developed at propeller shaft.