Cristian Nechifor
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Cristian Nechifor has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
Claudia Săvescu
Romanian Research and Development Institute for Gas Turbines COMOTI
4 shared publications- Daniel Lale
National Research and Development Institute for Gas Turbines—Romanian Research & Development Institute for Gas Turbines, 061126 Bucharest, Romania
3 shared publications - Mihaela Roman
Romanian Research and Development Institute for Gas Turbines COMOTI, Bucharest, Romania
3 shared publications - Adrian Stoicescu
Romanian Research and Development Institute for Gas Turbines COMOTI, Bucharest, Romania
2 shared publications - Claudia Borzea
Romanian Research and Development Institute for Gas Turbines COMOTI, 061126 Bucharest, Romania
2 shared publications - Daniel Useriu
INCDT COMOTI, Bucharest, Romania
2 shared publications
Latest Publications
- Open Access
- 17 November 2025
- Published by Editura Academiei Române in REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE
- Vol. 70 (4) , 597-602
AUTOMATION SYSTEM OF AN EDUCATIONAL TEST BENCH FOR NAVAL PISTON DIESEL ENGINES
The paper focuses on the custom automation system of a test bench for diesel engines used on navy ships, namely on tugboats. The test bench, with its automation system, is developed for practical training at a naval academy. The test bench aims to meet the highest standards in the education of Navy students and personnel. It facilitates undertaking practical laboratory works regarding the main constructive elements, operation, monitoring, and maintenance of four-stroke internal combustion engines, of the gearbox, as well as of the propeller load simulated by a hydraulic brake. The custom-made automation control system includes a modular cabinet with drives and automation sections, featuring a local command console for engine control and a remote command console for the entire test bench, with a large display for parameter monitoring.
- 17 November 2025
- Published by Editura Academiei Române in REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE
- Vol. 70 (4) , 597-602
Open AccessAUTOMATION SYSTEM OF AN EDUCATIONAL TEST BENCH FOR NAVAL PISTON DIESEL ENGINES
The paper focuses on the custom automation system of a test bench for diesel engines used on navy ships, namely on tugboats. The test bench, with its automation system, is developed for practical training at a naval academy. The test bench aims to meet the highest standards in the education of Navy students and personnel. It facilitates undertaking practical laboratory works regarding the main constructive elements, operation, monitoring, and maintenance of four-stroke internal combustion engines, of the gearbox, as well as of the propeller load simulated by a hydraulic brake. The custom-made automation control system includes a modular cabinet with drives and automation sections, featuring a local command console for engine control and a remote command console for the entire test bench, with a large display for parameter monitoring.
- Open Access
- 14 June 2025
- Published by Editura Academiei Române in REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE
- Vol. 70 (2) , 193-198
EXPERIMENTALLY VALIDATED STUDIES OF THERMOELECTRIC GENERATORS INSTALLED ON A COMPRESSOR TEST BENCH
This paper presents preliminary experimental work on a twin-screw compressor, aiming to validate numerical studies and demonstrate the potential of thermoelectric energy harvesting. Considering two thermoelectric modules, the experimental validations are conducted in an industrially relevant environment on a test bench for industrial air and gas compressors. The digital twin was simulated using finite element analysis, provided with a heat sink, and a fully coupled heat transfer and electric field was solved to assess the thermoelectric effect. This allows for complete modeling of the Peltier-Seebeck-Thomson effects. The compressor vibrations are also introduced for structural analysis to ascertain that the bismuth telluride thermoelectric modules are safe to use under sinusoidal mechanical vibrations. The thermoelectric generators are screwed onto the hottest part of the compressor skid, specifically the multiplier gearbox cover, which is splashed with hot lubrication oil from within. After the thermal stabilization of the compressor, we obtained a constant series voltage of around 0.4 VDC from the two thermoelectric generators, and the series current was measured to a value of 115 mA.
- 14 June 2025
- Published by Editura Academiei Române in REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE
- Vol. 70 (2) , 193-198
Open AccessEXPERIMENTALLY VALIDATED STUDIES OF THERMOELECTRIC GENERATORS INSTALLED ON A COMPRESSOR TEST BENCH
This paper presents preliminary experimental work on a twin-screw compressor, aiming to validate numerical studies and demonstrate the potential of thermoelectric energy harvesting. Considering two thermoelectric modules, the experimental validations are conducted in an industrially relevant environment on a test bench for industrial air and gas compressors. The digital twin was simulated using finite element analysis, provided with a heat sink, and a fully coupled heat transfer and electric field was solved to assess the thermoelectric effect. This allows for complete modeling of the Peltier-Seebeck-Thomson effects. The compressor vibrations are also introduced for structural analysis to ascertain that the bismuth telluride thermoelectric modules are safe to use under sinusoidal mechanical vibrations. The thermoelectric generators are screwed onto the hottest part of the compressor skid, specifically the multiplier gearbox cover, which is splashed with hot lubrication oil from within. After the thermal stabilization of the compressor, we obtained a constant series voltage of around 0.4 VDC from the two thermoelectric generators, and the series current was measured to a value of 115 mA.
- 1 April 2025
- Published by Comitetul National Roman al Consiliului Mondial al Energiei in EMERG - Energy. Environment. Efficiency. Resources. Globalization
- Vol. 11 (1) , 114-128
AUTOMATION AND ELECTRICAL CONTROL OF A COMPRESSED AIR ENERGY STORAGE SYSTEM
This work aims to develop the automation system for the motor-compressor and expander-generator systems of a compressed air energy installation, henceforth referred to as ROCAES. Considering that the expander and compressor operate independently according to the scope of work, a solution comprising two separate automation systems that work together was chosen. The software programming was performed relying on the established parameter lists and in accordance with the project’s piping and instrumentation diagram, as well as the equipment mounted on the skid and in the automation cabinets. Guidelines are provided for future development, emphasizing the strengths and weaknesses of the solution.
- 1 April 2025
- Published by Comitetul National Roman al Consiliului Mondial al Energiei in EMERG - Energy. Environment. Efficiency. Resources. Globalization
- Vol. 11 (1) , 114-128
AUTOMATION AND ELECTRICAL CONTROL OF A COMPRESSED AIR ENERGY STORAGE SYSTEM
This work aims to develop the automation system for the motor-compressor and expander-generator systems of a compressed air energy installation, henceforth referred to as ROCAES. Considering that the expander and compressor operate independently according to the scope of work, a solution comprising two separate automation systems that work together was chosen. The software programming was performed relying on the established parameter lists and in accordance with the project’s piping and instrumentation diagram, as well as the equipment mounted on the skid and in the automation cabinets. Guidelines are provided for future development, emphasizing the strengths and weaknesses of the solution.
- Open Access
- 25 March 2025
- Published by Editura Academiei Române in REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE
- Vol. 70 (1) , 9-14
EXPERIMENTAL STUDY OF A PIEZOELECTRIC HARVESTER VIBRATING ON AN INDUSTRIAL SCREW COMPRESSOR
The paper presents preliminary experimental works on a twin-screw compressor to validate and demonstrate piezoelectric energy harvesting. The experiments target an industrially relevant environment: a test bench for industrial air and gas compressors. This work was only possible after previous studies assessing the piezoelectric harvester’s behavior, considering essential factors. In our case, a high working temperature may negatively influence the piezoelectric response and can even damage the material; hence, it should be avoided as much as possible. The piezoelectric harvester’s resonant frequency ought to be adjusted in real-time to match as closely as possible the target vibration frequency of the male rotor, of ~83 Hz. We obtained a voltage peak response of ~4 VAC and a maximum measured RMS current of ~515 µA. The RMS power, calculated at about 1.5 mW, was deemed very satisfactory for a piezoelectric device.
- 25 March 2025
- Published by Editura Academiei Române in REVUE ROUMAINE DES SCIENCES TECHNIQUES — SÉRIE ÉLECTROTECHNIQUE ET ÉNERGÉTIQUE
- Vol. 70 (1) , 9-14
Open AccessEXPERIMENTAL STUDY OF A PIEZOELECTRIC HARVESTER VIBRATING ON AN INDUSTRIAL SCREW COMPRESSOR
The paper presents preliminary experimental works on a twin-screw compressor to validate and demonstrate piezoelectric energy harvesting. The experiments target an industrially relevant environment: a test bench for industrial air and gas compressors. This work was only possible after previous studies assessing the piezoelectric harvester’s behavior, considering essential factors. In our case, a high working temperature may negatively influence the piezoelectric response and can even damage the material; hence, it should be avoided as much as possible. The piezoelectric harvester’s resonant frequency ought to be adjusted in real-time to match as closely as possible the target vibration frequency of the male rotor, of ~83 Hz. We obtained a voltage peak response of ~4 VAC and a maximum measured RMS current of ~515 µA. The RMS power, calculated at about 1.5 mW, was deemed very satisfactory for a piezoelectric device.
- Open Access
- 2 April 2024
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 14 (2) , 13456-13462
Experimental Analysis of Twin Screw Compressor's Energetic Efficiency Depending on Volume Ratio
The current paper presents the results of the experimental analysis to assess and optimize the twin-screw compressor’s efficiency by varying the volume ratio. The experimental tests are conducted on the compressor's test bench, with a dedicated automation system inside the control console. The control and monitoring software allows parameter recording for subsequent visualization, data curation, and post-processing. The evaluation of screw compressor's performance requires a simultaneous analysis of the thermodynamic and flow processes, both of which depend on the compressor’s geometry. The obtained volumetric and adiabatic efficiencies are good, with values over 0.88 and 0.69, respectively.
- 2 April 2024
- Published by Engineering, Technology & Applied Science Research in Engineering, Technology & Applied Science Research
- Vol. 14 (2) , 13456-13462
Open AccessExperimental Analysis of Twin Screw Compressor's Energetic Efficiency Depending on Volume Ratio
The current paper presents the results of the experimental analysis to assess and optimize the twin-screw compressor’s efficiency by varying the volume ratio. The experimental tests are conducted on the compressor's test bench, with a dedicated automation system inside the control console. The control and monitoring software allows parameter recording for subsequent visualization, data curation, and post-processing. The evaluation of screw compressor's performance requires a simultaneous analysis of the thermodynamic and flow processes, both of which depend on the compressor’s geometry. The obtained volumetric and adiabatic efficiencies are good, with values over 0.88 and 0.69, respectively.
- Open Access
- 6 January 2022
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 354, 00044
Modular automation cabinet for proactive monitoring in ATEX Zone 2
The paper presents an automation system dedicated to oil & gas machinery applications, such as electrical gas compressors. The future aim is to introduce it into the Romanian oil & gas industry. The system consists of a low size cabinet and its dependencies, which can be used in ATEX Zone 2. The electronic equipment is dimensioned and chosen according to the standards in force, so that the limited current and voltage requirements for methane gas to be met. The key feature is that this system complies with all ATEX standards for Zone 2. Moreover, it can also be a mobile and modular solution if needed, for a versatile and easy use in proactive monitoring of multiple locations across various compressor plants. The design, wireless transmission and possible implementation of this cabinet are presented. Remote data transmission via Wi-Fi and RS-485 communication interfaces between the devices is considered, due to several advantages: mobility, versatility, wide compatibility, environmentally friendly, as well as higher resources efficiency (reducing time and costs).
- 6 January 2022
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 354, 00044
Open AccessModular automation cabinet for proactive monitoring in ATEX Zone 2
The paper presents an automation system dedicated to oil & gas machinery applications, such as electrical gas compressors. The future aim is to introduce it into the Romanian oil & gas industry. The system consists of a low size cabinet and its dependencies, which can be used in ATEX Zone 2. The electronic equipment is dimensioned and chosen according to the standards in force, so that the limited current and voltage requirements for methane gas to be met. The key feature is that this system complies with all ATEX standards for Zone 2. Moreover, it can also be a mobile and modular solution if needed, for a versatile and easy use in proactive monitoring of multiple locations across various compressor plants. The design, wireless transmission and possible implementation of this cabinet are presented. Remote data transmission via Wi-Fi and RS-485 communication interfaces between the devices is considered, due to several advantages: mobility, versatility, wide compatibility, environmentally friendly, as well as higher resources efficiency (reducing time and costs).
- 27 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Automation Control System for Naval Propulsion Retrofitting
Nowadays, automation systems for naval propulsion groups with gas turbines use programmable logic controllers for a precise and reliable control. The automation system is designed so as to be able to connect using signal cables to the transducers monitoring the engine’s parameters, via adapters, so that the command and regulation functions to be fully automatized. These signals are managed by means of the software program implemented in the PLC, and subsequent data acquisition. One of the important problems is the available resource of the propulsion group, until capital repair is required. The remaining lifetime depends on the operating regimes of the gas turbine engine. This problem is more pronounced in the propulsion groups equipping navy ships, where the dynamic regimes of gas turbine engines are much more demanding, and hence the pre-established operating limits may be exceeded. The automation configuration presented herein ensures the accurate computation and precise control of essential parameters for which the direct measurement is not possible using transducers. These parameters are the exhaust gas temperature, the power developed by the engine and implicitly the torque developed at propeller shaft.
- 27 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Automation Control System for Naval Propulsion Retrofitting
Nowadays, automation systems for naval propulsion groups with gas turbines use programmable logic controllers for a precise and reliable control. The automation system is designed so as to be able to connect using signal cables to the transducers monitoring the engine’s parameters, via adapters, so that the command and regulation functions to be fully automatized. These signals are managed by means of the software program implemented in the PLC, and subsequent data acquisition. One of the important problems is the available resource of the propulsion group, until capital repair is required. The remaining lifetime depends on the operating regimes of the gas turbine engine. This problem is more pronounced in the propulsion groups equipping navy ships, where the dynamic regimes of gas turbine engines are much more demanding, and hence the pre-established operating limits may be exceeded. The automation configuration presented herein ensures the accurate computation and precise control of essential parameters for which the direct measurement is not possible using transducers. These parameters are the exhaust gas temperature, the power developed by the engine and implicitly the torque developed at propeller shaft.