Brian K. Diefenderfer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Brian K. Diefenderfer has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Gerardo W. Flintsch
Center for Sustainability and Resilience Infrastructure at VTTI, Virginia Polytechnic Institute and State University, 3500 Transportation Research Plaza, Blacksburg, VA 24061, USA
4 shared publications - Benjamin F. Bowers
Department of Civil and Environmental Engineering, Auburn University, Auburn, AL
2 shared publications - David H. Timm
Department of Civil and Environmental Engineering, Auburn University, Auburn, AL
2 shared publications - Ernesto Urbaez Perez
Center for Sustainability and Resilience Infrastructure at VTTI, Virginia Polytechnic Institute and State University, 3500 Transportation Research Plaza, Blacksburg, VA 24061, USA
2 shared publications - Fabrizio Meroni
Istituto Nazionale di Geofisica e Vulcanologia (INGV), Sezione Milano, 20133 Milan, Italy
2 shared publications - Ilker Boz
Virginia Transportation Research Council, Virginia Department of Transportation, Charlottesville, VA
2 shared publications
Latest Publications
- 24 July 2024
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2678 (12) , 1416-1427
Pilot Study to Incorporate Network-Level Structural Condition in Agency Pavement Management Practices
The structural condition of roadway pavements is crucial in assessing the overall health of roadway networks and making informed decisions on maintenance and rehabilitation interventions. While current pavement management systems (PMSs) primarily rely on surface distress conditions, incorporating structural condition assessment at the network level can enhance decision-making processes. An approach is presented to incorporate network-level structural condition measurements obtained from the traffic speed deflectometer (TSD) in the Virginia Department of Transportation PMS. This involves determining a structural number, calculated using TSD measurements, selecting an appropriate structural condition measure (remaining structural service life) for use in the PMS, enhancing treatment selection decision trees, and conducting a cost analysis. The TSD-derived effective structural number, obtained following the American Association of State Highways and Transportation Officials (AASHTO) 1993 empirical design procedure, is utilized with traffic projections and other design information to estimate the remaining structural service life. In the treatment recommendation process, surface distress information is combined with the structural condition assessment, considering budget allocation and pavement useful life. For US Route 29 in Virginia, comparing treatment costs revealed a potential 33.2% cost saving for one maintenance cycle using the augmented decision process, which includes structural assessment, compared with surface distress assessment alone. This approach could provide a comprehensive framework for integrating structural condition assessment in PMSs, enabling more effective and cost-efficient decision-making for roadway networks. To further optimize resource allocation and improve accuracy, combining the augmented treatment selection process with deterioration predictions for a cost analysis over several maintenance cycles is recommended.
- 24 July 2024
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2678 (12) , 1416-1427
Pilot Study to Incorporate Network-Level Structural Condition in Agency Pavement Management Practices
The structural condition of roadway pavements is crucial in assessing the overall health of roadway networks and making informed decisions on maintenance and rehabilitation interventions. While current pavement management systems (PMSs) primarily rely on surface distress conditions, incorporating structural condition assessment at the network level can enhance decision-making processes. An approach is presented to incorporate network-level structural condition measurements obtained from the traffic speed deflectometer (TSD) in the Virginia Department of Transportation PMS. This involves determining a structural number, calculated using TSD measurements, selecting an appropriate structural condition measure (remaining structural service life) for use in the PMS, enhancing treatment selection decision trees, and conducting a cost analysis. The TSD-derived effective structural number, obtained following the American Association of State Highways and Transportation Officials (AASHTO) 1993 empirical design procedure, is utilized with traffic projections and other design information to estimate the remaining structural service life. In the treatment recommendation process, surface distress information is combined with the structural condition assessment, considering budget allocation and pavement useful life. For US Route 29 in Virginia, comparing treatment costs revealed a potential 33.2% cost saving for one maintenance cycle using the augmented decision process, which includes structural assessment, compared with surface distress assessment alone. This approach could provide a comprehensive framework for integrating structural condition assessment in PMSs, enabling more effective and cost-efficient decision-making for roadway networks. To further optimize resource allocation and improve accuracy, combining the augmented treatment selection process with deterioration predictions for a cost analysis over several maintenance cycles is recommended.
- 31 March 2024
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2678 (10) , 1472-1483
Accelerated Pavement Testing of Re-Recycled Cold Central Plant Recycled Asphalt Mixtures
Cold central plant recycled asphalt mixtures (CCPR) have been shown to provide a high-quality, economical, and environmentally conscious asphalt base mixture. Existing literature, however, does not indicate what would be an appropriate future rehabilitation method for a pavement that includes CCPR. Given the previously cited benefits of CCPR, it is logical to ask whether a CCPR can be re-recycled and, if so, how will it perform? This paper presents a study of a test section containing a re-recycled CCPR placed at the National Center for Asphalt Technology Test Track. CCPR from a Virginia Department of Transport study on the Test Track was recovered, re-recycled, and placed at 5-in. thick with a 2-in. asphalt concrete (AC) overlay. In preparing for a re-recycled CCPR layer, milling an existing CCPR layer resulted in a coarser gradation and lower indirect tensile strength values. Initially, the re-recycled CCPR test section did not perform well owing to moisture in the aggregate base present during construction of the re-recycled CCPR layer. It is suspected that this moisture negatively affected the curing of the re-recycled CCPR layer. Thus, the re-recycled CCPR layer was milled and re-recycled again (3rd generation re-recycled CCPR) and placed at 5-in. thick with a 2-in. AC overlay. The 3rd generation re-recycled CCPR performed well through 3 million equivalent single axle loads (ESALs), the same number of ESALs that resulted in fatigue cracking and rutting failures in the initial re-recycled CCPR.
- 31 March 2024
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2678 (10) , 1472-1483
Accelerated Pavement Testing of Re-Recycled Cold Central Plant Recycled Asphalt Mixtures
Cold central plant recycled asphalt mixtures (CCPR) have been shown to provide a high-quality, economical, and environmentally conscious asphalt base mixture. Existing literature, however, does not indicate what would be an appropriate future rehabilitation method for a pavement that includes CCPR. Given the previously cited benefits of CCPR, it is logical to ask whether a CCPR can be re-recycled and, if so, how will it perform? This paper presents a study of a test section containing a re-recycled CCPR placed at the National Center for Asphalt Technology Test Track. CCPR from a Virginia Department of Transport study on the Test Track was recovered, re-recycled, and placed at 5-in. thick with a 2-in. asphalt concrete (AC) overlay. In preparing for a re-recycled CCPR layer, milling an existing CCPR layer resulted in a coarser gradation and lower indirect tensile strength values. Initially, the re-recycled CCPR test section did not perform well owing to moisture in the aggregate base present during construction of the re-recycled CCPR layer. It is suspected that this moisture negatively affected the curing of the re-recycled CCPR layer. Thus, the re-recycled CCPR layer was milled and re-recycled again (3rd generation re-recycled CCPR) and placed at 5-in. thick with a 2-in. AC overlay. The 3rd generation re-recycled CCPR performed well through 3 million equivalent single axle loads (ESALs), the same number of ESALs that resulted in fatigue cracking and rutting failures in the initial re-recycled CCPR.
- 24 June 2022
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2677 (1) , 409-419
Structural Performance of an Asphalt Pavement Containing Cold Central Plant Recycling and Full-Depth Reclamation
Pavement recycling techniques are often perceived as only applicable to lower traffic volume roadways. However, recent studies have shown their potential for long service lives in higher traffic volume applications. This study documented the response of an asphalt pavement section, constructed using full-depth reclamation (FDR) and cold central plant recycling (CCPR), on a portion of I-64 in Virginia reconstructed between 2016 and 2019. The pavement section was instrumented and the response was compared with a similarly instrumented pavement section (Section S12) placed at the National Center for Asphalt Technology (NCAT) Test Track in 2012. Previous studies have shown that Section S12 is a long-life pavement and it carried 30 million equivalent single axle loads (ESALs) while showing no evidence of deterioration at the pavement surface or from installed instrumentation. The results from the I-64 Segment II project showed that it had much lower horizontal strain values at the bottom of the asphalt layers but slightly higher vertical pressure values on top of the subgrade when compared with NCAT Section S12. Despite the slightly higher values (about 1 pounds per square inch [psi] difference), the vertical pressure on top of the subgrade was very low for both pavement sections. The study confirmed that a recycled pavement section could be constructed and result in low strain and pressure values and is expected to have a long service life in a high traffic volume environment.
- 24 June 2022
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2677 (1) , 409-419
Structural Performance of an Asphalt Pavement Containing Cold Central Plant Recycling and Full-Depth Reclamation
Pavement recycling techniques are often perceived as only applicable to lower traffic volume roadways. However, recent studies have shown their potential for long service lives in higher traffic volume applications. This study documented the response of an asphalt pavement section, constructed using full-depth reclamation (FDR) and cold central plant recycling (CCPR), on a portion of I-64 in Virginia reconstructed between 2016 and 2019. The pavement section was instrumented and the response was compared with a similarly instrumented pavement section (Section S12) placed at the National Center for Asphalt Technology (NCAT) Test Track in 2012. Previous studies have shown that Section S12 is a long-life pavement and it carried 30 million equivalent single axle loads (ESALs) while showing no evidence of deterioration at the pavement surface or from installed instrumentation. The results from the I-64 Segment II project showed that it had much lower horizontal strain values at the bottom of the asphalt layers but slightly higher vertical pressure values on top of the subgrade when compared with NCAT Section S12. Despite the slightly higher values (about 1 pounds per square inch [psi] difference), the vertical pressure on top of the subgrade was very low for both pavement sections. The study confirmed that a recycled pavement section could be constructed and result in low strain and pressure values and is expected to have a long service life in a high traffic volume environment.
- 22 January 2021
- Published by The National Academies Press
Proposed AASHTO Practice and Tests for Process Control and Product Acceptance of Asphalt-Treated Cold Recycled Pavements
Download a PDF of "Proposed AASHTO Practice and Tests for Process Control and Product Acceptance of Asphalt-Treated Cold Recycled Pavements" by the National Academies of Sciences, Engineering, and Medicine for free.
- 22 January 2021
- Published by The National Academies Press
Proposed AASHTO Practice and Tests for Process Control and Product Acceptance of Asphalt-Treated Cold Recycled Pavements
Download a PDF of "Proposed AASHTO Practice and Tests for Process Control and Product Acceptance of Asphalt-Treated Cold Recycled Pavements" by the National Academies of Sciences, Engineering, and Medicine for free.
- 26 August 2020
- Published by Springer Nature
- p. 108-117
Impact of Mix Design Optimization on HMA Rutting Performance Under Accelerated Pavement Testing
- 26 August 2020
- Published by Springer Nature
- p. 108-117
Impact of Mix Design Optimization on HMA Rutting Performance Under Accelerated Pavement Testing
- 1 January 2011
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2253 (1) , 3-9
Time-Dependent Structural Response of Full-Depth Reclamation
Innovative pavement rehabilitation techniques, such as in-place recycling, are becoming more prevalent as highway agencies face an ever-increasing list of pavement maintenance needs and declining or stagnant budgets. Full-depth reclamation (FDR) has been shown to be a cost-effective alternative to deep milling and repaving to rehabilitate deteriorated flexible pavements. The results of previous FDR studies that investigated pavement structural capacity through the use of deflection testing suggest that long-term strength gain may be achieved through curing; however, such a strength gain has not been well quantified. This study documented the in situ structural testing, with a falling weight deflectometer, of three FDR projects constructed in 2008. Deflection testing was performed periodically at the project sites in the first 2 years after reclamation. This study showed that an accurate estimation of the final structural capacity of an FDR project may not feasibly be achieved immediately after the project has been completed and that it could vary greatly depending on the stabilizing agent used. If data from early-age testing are used to calculate design parameters for future projects, the parameters may be too conservative and result in the loss of potential cost savings through the use of unnecessary overlay materials. A cost analysis, based on data collected in this study, showed that these potential cost savings could approach $37,000 per lane mile. Further mechanistic-based studies of the time-dependent structural response of FDR materials are recommended.
- 1 January 2011
- Published by SAGE Publications in Transportation Research Record: Journal of the Transportation Research Board
- Vol. 2253 (1) , 3-9
Time-Dependent Structural Response of Full-Depth Reclamation
Innovative pavement rehabilitation techniques, such as in-place recycling, are becoming more prevalent as highway agencies face an ever-increasing list of pavement maintenance needs and declining or stagnant budgets. Full-depth reclamation (FDR) has been shown to be a cost-effective alternative to deep milling and repaving to rehabilitate deteriorated flexible pavements. The results of previous FDR studies that investigated pavement structural capacity through the use of deflection testing suggest that long-term strength gain may be achieved through curing; however, such a strength gain has not been well quantified. This study documented the in situ structural testing, with a falling weight deflectometer, of three FDR projects constructed in 2008. Deflection testing was performed periodically at the project sites in the first 2 years after reclamation. This study showed that an accurate estimation of the final structural capacity of an FDR project may not feasibly be achieved immediately after the project has been completed and that it could vary greatly depending on the stabilizing agent used. If data from early-age testing are used to calculate design parameters for future projects, the parameters may be too conservative and result in the loss of potential cost savings through the use of unnecessary overlay materials. A cost analysis, based on data collected in this study, showed that these potential cost savings could approach $37,000 per lane mile. Further mechanistic-based studies of the time-dependent structural response of FDR materials are recommended.