DTDavid H. Timm

David H. Timm

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


David H. Timm has a total of 35 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Evaluating Cold Central Plant Recycling in High Traffic Volume Applications: A Full-Scale Test Track Study

    by David H. Timm, Benjamin F. Bowers, Brian K. Diefenderfer, Elizabeth Turochy

    Asphalt pavements in the United States often incorporate recycled materials, with some highway agencies allowing up to 25%–30% reclaimed asphalt pavement (RAP) in lower courses. While this improves sustainability, using higher RAP percentages could significantly enhance environmental benefits if performance remains similar. One method of using higher RAP contents is with Cold Central Plant Recycling (CCPR), a technique that blends RAP with emulsified or foamed asphalt and, optionally, an active filler to create a nearly 100% recycled asphalt-stabilized base course material at ambient temperatures. However, its long-term performance under heavy traffic is unknown. To address this uncertainty, Virginia Department of Transportation funded a multi-section CCPR experiment at the National Center for Asphalt Technology Test Track beginning in 2012. The thinnest cross section included 4 in. of conventional asphalt surface layers over 5 in. of CCPR, placed on an aggregate base over subgrade. The test section was instrumented to monitor structural responses and surface performance under accelerated loading by triple-trailer trucks. Regular falling weight deflectometer testing enabled backcalculation of material properties over time. The testing lasted nearly 30 million equivalent single axle loads (MESALs) before any surface cracking was evident and the structure endured 40 MESALs before being taken out of service. This far exceeded expectations for a material not yet tested in high traffic and highlights CCPR’s potential for future use. This paper details the test section’s construction, long-term performance, forensic findings following testing, and serves as an important case study for application of CCPR in high traffic volume conditions.

  • Forensic Evaluation of a Dry-Process Rubber-Modified Asphalt Pavement

    by Matthew H. Kmetz, David Timm, Carolina Rodezno

    Atypical horizontal cracking and shear distress, paired with extensive bottom-up fatigue cracking, were identified in a dry-process rubber-modified flexible pavement section belonging to the Additive Group experiment at the National Center for Asphalt Technology Test Track. Exposed to the same accelerated trafficking level, the wet-process styrene butadiene styrene- modified control section displayed no such distress. An initial forensic evaluation characterized the distress and proposed mechanism(s) for distress initiation/propagation using analyses of the asphalt mixtures, backcalculated layer moduli, measured pavement responses, structural response simulation via Waterways Experiment Station Layered Elastic Analysis (WESLEA) for Windows 3.0 (WFW), and fatigue cracking damage evolution simulation via FlexPAVE 1.1 (FP). The objective of this paper was to provide support for the theories established in the previous investigation (on the mechanisms responsible for distress). Therefore, shear strength testing of the mixtures was performed, where a significant reduction in shear stress resistance was observed for the rubber-modified material versus the control material. Structural response simulation via FP confirmed the presence of significant internal horizontal shear stress development with the asphalt concrete (AC) layer under dual-tire loadings similar to the conditions found at the Test Track. Therefore, this could have led to the initiation and propagation of horizontal cracking and shear distress, given the rubber-modified mixture’s reduced capacity for shear resistance. The horizontal cracking condition in the rubber-modified section was modeled via WFW. The resulting tensile strain responses showed the best agreement with the field-measured quantities, indicating that horizontal cracking in the rubber-modified AC layer magnified the measured tensile strain responses.

  • Initial Forensic Evaluation of a Dry-Process Rubber-Modified Asphalt Pavement

    by Matthew H. Kmetz, Samina Samrose, David Timm, Carolina Rodezno

    The Additive Group (AG) experiment at the National Center for Asphalt Technology (NCAT) Test Track includes a section paved with a dry-process rubber-modified asphalt mixture (GTRDry) which has displayed severe levels of cracking after 10 million equivalent single-axle loads (ESAL) of accelerated trafficking. In the same period, the styrene–butadiene–styrene (SBS) modified control mixture displayed no cracking. Both mixtures displayed similar laboratory evaluated dynamic modulus |E*| and fatigue properties. The objective of this investigation was to determine the cause of the unexpected cracking observed in the GTRDry test section via forensic analysis, laboratory data, measured structural responses, and structural simulation. It was found that GTRDry had significantly lower foundation support relative to the control, and its average temperature-corrected asphalt concrete (AC) modulus (E 68 ) was lower than expected (based on the results of |E*| testing). Both factors contributed to the high tensile strains at the bottom of the AC layer (double those of the control). This was assumed to be the sole cause of the GTRDry cracking (a traditional bottom-up fatigue cracking mechanism), until forensic coring revealed mid-depth, horizontal cracking, prompting structural simulations via WESLEA. The results indicated that the lower AC and support moduli of the GTRDry section resulted in higher flexural strain responses. Peak shear stresses occurred near the location of mid-depth cracking; however, the magnitudes were found to be independent of the layer moduli, remaining relatively similar between the two sections. It was, therefore, concluded that the paved N1 (GTRDry) mixture was potentially more susceptible to horizontal cracking and bottom-up fatigue cracking distresses than the SBS-modified control.


  • Using Statistical Analysis to Assess the Default Structural Properties of Alabama Department of Transportation Base and Subgrade Materials Used for Flexible Pavement Design

    by Don Guy V. V. Biessan, Benjamin F. Bowers, David H. Timm, Scott W. George, Frank Bell, John P. Jennings

    Structural properties of materials are important during flexible pavement design since they represent the capacity to withstand traffic loads. It is essential to regularly update the structural inputs for design to achieve optimum pavement designs. Alabama Department of Transportation (ALDOT) updated the structural inputs for hot-mix-asphalt in 2009, but not yet those for base and subgrade materials. Therefore, the goal of this study was to evaluate and update the materials’ structural inputs used by ALDOT for: 1) aggregate base (limestone and sandstone), 2) stabilized base (full-depth reclamation with cement [FDR-C]) and soil-cement [S-C]), and 3) subgrade. For that purpose, numerous laboratory and field-testing results for those materials were used to obtain resilient modulus (M R ) and structural coefficients, which were compared with ALDOT default values using statistical analysis methods. For aggregate base, the M R of limestone was statistically greater while the M R of sandstone was statistically lower than the default design values. For stabilized aggregate base, the M R of FDR-C and S-C were statistically lower than the default values when using 7-day unconfined compressive strength (UCS) and statistically greater when using 28-day UCS. The use of 28-day UCS in existing correlation equations to obtain structural properties of FDR-C and S-C was shown to provide more realistic values and, therefore, is recommended for design purposes. The practical difference between the new base materials properties and the default design values was also evaluated through a case study. For subgrade, new recommended M R values were provided for all soil types.


  • Laboratory and Field Performance Characterization of Recycled-Plastic-Modified Asphalt Mixtures at the National Center for Asphalt Technology Test Track

    by Fan Yin, Matthew Kmetz, David Timm, Randy West, Adam Taylor

    This study evaluated the performance of two recycled-plastic-modified (RPM) asphalt mixtures versus a nonplastic control mixture through laboratory performance testing, FlexPAVE™ simulations, and accelerated pavement testing at the National Center for Asphalt Technology (NCAT) Test Track. One RPM mixture used the wet process of adding linear low-density polyethylene (LLDPE) for asphalt binder modification, and the other the dry process of adding LLDPE for mixture modification using a drop-in approach. The nonplastic control mixture used a binder modified by styrene-butadiene-styrene. Each mixture was produced in an asphalt plant and placed as a single-lift asphalt layer of a structural test section at the NCAT Test Track. Laboratory performance testing showed that the wet plastic mixture had comparable properties to the control, while the dry plastic mixture had significantly higher stiffness, better rutting resistance, but worse cracking resistance than the control mixture. Using a representative pavement structure and layer properties as inputs, FlexPAVE™ simulations predicted that the dry plastic section would have the best fatigue-cracking performance, followed by the control and wet plastic sections, respectively. In situ pavement structural characterization data showed the control section had lower asphalt layer moduli, higher granular base and subgrade moduli, and lower measured strain at the bottom of the asphalt layer than the two plastic sections. Through 10 million equivalent single axle loads of trafficking, all three test sections showed steady smoothness and comparable rutting and friction performance. The dry plastic section had 3.5% surface cracking, while the control and wet plastic sections remained intact with no cracking.


  • Accelerated Pavement Testing of Re-Recycled Cold Central Plant Recycled Asphalt Mixtures

    by Benjamin F. Bowers, David H. Timm, Elizabeth Turochy, Brian K. Diefenderfer

    Cold central plant recycled asphalt mixtures (CCPR) have been shown to provide a high-quality, economical, and environmentally conscious asphalt base mixture. Existing literature, however, does not indicate what would be an appropriate future rehabilitation method for a pavement that includes CCPR. Given the previously cited benefits of CCPR, it is logical to ask whether a CCPR can be re-recycled and, if so, how will it perform? This paper presents a study of a test section containing a re-recycled CCPR placed at the National Center for Asphalt Technology Test Track. CCPR from a Virginia Department of Transport study on the Test Track was recovered, re-recycled, and placed at 5-in. thick with a 2-in. asphalt concrete (AC) overlay. In preparing for a re-recycled CCPR layer, milling an existing CCPR layer resulted in a coarser gradation and lower indirect tensile strength values. Initially, the re-recycled CCPR test section did not perform well owing to moisture in the aggregate base present during construction of the re-recycled CCPR layer. It is suspected that this moisture negatively affected the curing of the re-recycled CCPR layer. Thus, the re-recycled CCPR layer was milled and re-recycled again (3rd generation re-recycled CCPR) and placed at 5-in. thick with a 2-in. AC overlay. The 3rd generation re-recycled CCPR performed well through 3 million equivalent single axle loads (ESALs), the same number of ESALs that resulted in fatigue cracking and rutting failures in the initial re-recycled CCPR.


  • Laboratory Characterization of Additive-Modified Asphalt Concrete Mixtures

    by Matthew Kmetz, David Timm, Carolina Rodezno, Nam Tran, Fan Yin

    There is a need for a more rapid system of evaluation and implementation for new and existing asphalt additives, especially because of the prohibitive cost of full-scale performance evaluations. To help to meet this need, the Additive Group (AG) experiment at the National Center for Asphalt Technology (NCAT) was developed and began in 2021. A comprehensive laboratory evaluation of six mixtures, each modified with a popular additive type selected by the AG state DOT sponsors, was conducted. Simultaneously, full-scale test sections were constructed at the NCAT test track to evaluate the field performance and structure behavior of each modified mixture. Trafficking of these test sections is currently underway, and estimated to be completed in 2024, at which point an investigation linking the laboratory and field results will be done. This paper presents the completed laboratory evaluation of each AG mixture via complex dynamic modulus (E*), direct tension cyclic fatigue, and bending beam fatigue testing. The wet-process rubber modified mixture was found to have reduced E* and initial flexural stiffness, but increased fatigue resistance, relative to the styrene-butadiene-styrene (SBS)-modified control mixture. The dry-process rubber-modified mixture displayed similar trends, though to a lesser degree. Conversely, the dry-process plastic-modified mixture was found to have increased E* and initial flexural stiffness, but reduced fatigue resistance, relative to the SBS-modified control mixture. The other AG mixtures—a dry-process fiber and a wet-process plastic-modified mixture—were found to display E*, initial flexural stiffness, and fatigue resistance similar to that of the SBS-modified control mixture.


  • Long-Term Performance and Forensic Evaluation of an Asphalt Pavement with Cold Central Plant Recycled Asphalt

    by Benjamin F. Bowers, Tiana Lynn, David H. Timm, Brian K. Diefenderfer, Surendra C. Gatiganti

    In 2012 Virginia Department of Transportation constructed two test sections at the National Center for Asphalt Technology Test Track containing asphalt processed via cold central plant recycling (CCPR) with identical asphalt overlays. One section contained a stabilized base beneath the CCPR layer (Section S12), similar to a full-depth reclamation layer; the other included an unstabilized aggregate base beneath the CCPR layer (Section N4). Both sections were subjected to trafficking by loaded trucks for a total of 30 million equivalent single axle loads. Minor cracking was observed at the surface of the section with the unstabilized base; the section with the stabilized foundation exhibited no surface cracking. Furthermore, strain, pressure, and deflection measurements showed better performance for the section with the stabilized foundation than the section with the unstabilized base. Because of the relatively unchanged performance of Section S12, it was taken out of service to conduct a forensic investigation. This paper presents the analysis of the instrumentation results, coring, trenching, and mechanistic testing and modeling, to better understand and compare the performance between sections. The stabilized base was found to greatly reduce bending action in the section, exhibited no substantial rutting, but also contained what appeared to be some shrinkage cracks. However, these cracks did not propagate to the surface, indicating that the CCPR layer may be an effective crack mitigator. Further, it was found that mechanistic modeling using AASHTOWare Pavement ME design software overestimated the rutting but predicted similar international roughness index and cracking to that observed in the field.


  • Structural Performance of an Asphalt Pavement Containing Cold Central Plant Recycling and Full-Depth Reclamation

    by Brian K. Diefenderfer, Gerardo Flintsch, Wenjing Xue, Fabrizio Meroni, Ilker Boz, David Timm

    Pavement recycling techniques are often perceived as only applicable to lower traffic volume roadways. However, recent studies have shown their potential for long service lives in higher traffic volume applications. This study documented the response of an asphalt pavement section, constructed using full-depth reclamation (FDR) and cold central plant recycling (CCPR), on a portion of I-64 in Virginia reconstructed between 2016 and 2019. The pavement section was instrumented and the response was compared with a similarly instrumented pavement section (Section S12) placed at the National Center for Asphalt Technology (NCAT) Test Track in 2012. Previous studies have shown that Section S12 is a long-life pavement and it carried 30 million equivalent single axle loads (ESALs) while showing no evidence of deterioration at the pavement surface or from installed instrumentation. The results from the I-64 Segment II project showed that it had much lower horizontal strain values at the bottom of the asphalt layers but slightly higher vertical pressure values on top of the subgrade when compared with NCAT Section S12. Despite the slightly higher values (about 1 pounds per square inch [psi] difference), the vertical pressure on top of the subgrade was very low for both pavement sections. The study confirmed that a recycled pavement section could be constructed and result in low strain and pressure values and is expected to have a long service life in a high traffic volume environment.


  • Comparison of Relative Structural Characterization Methods for Additive-Modified Asphalt Mixtures

    by David H. Timm, Fan Yin, Nam Tran, Megan Foshee, Carolina Rodezno

    The evaluation, adoption, and efficient deployment of asphalt additives in flexible pavements has historically been a relatively slow process, requiring years of testing and evaluation before a new product may be fully and readily used in pavement cross-sections. However, the fast-paced and innovative nature of the additive marketplace produces numerous products that have the potential to improve performance, reduce costs, or both, but have been hindered by slow deployment. To address the need for a more rapid set of evaluation tools, the National Center for Asphalt Technology Test Track initiated an Additive Group experiment in 2021 to build full-scale pavement test sections modified with several asphalt additives, including recycled tire rubber, recycled plastics, reactive polymers, and aramid fibers. Data will be collected from these test sections to develop a framework for evaluating asphalt additives in the future. Phase 1 of the investigation was to conduct limited laboratory testing and structural analysis from which a group of additives would be selected for full-scale construction and evaluation. Focused on fatigue cracking, this paper details the laboratory testing conducted for Phase 1 and two different structural pavement analysis methods using FlexPAVE™ and WESLEA. Even though the two structural pavement analysis methods are very different, the FlexPAVE and WESLEA analyses provided strongly correlated predicted cracking performance, remarkably similar predictions of equivalent pavement thicknesses, and nearly identical structural layer coefficients. It is recommended that these two approaches be further evaluated against laboratory and field performance data that will be collected from the Additive Group experiment.