Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ihor Hrytsai has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The Development of Computer Models of Complex Machining Methods in Mechanical Engineering for Systematic Research, Control and Optimization

    by Ihor Hrytsay, Petro Pukach, Myroslava Vovk

    The results of the development and practical application of a comprehensive system for studying gear cutting processes are presented. The processes are traditional hobbing, modern power skiving, and radial-circular methods. Carrying out these processes is based on the gear teeth continuous generating method using complex kinematics. This complicates the analysis, description and modeling of the processes. The developed system provides for a logical sequence of step-by-step modeling and simulation of interrelated processes and phenomena accompanying gear processing. Reproducing volumetric chips and calculating their parameters provides the basis for determining deformation and contact processes, cutting forces, elastic deformations, machining accuracy and energy costs per operation. After establishing the operation to overcome friction and heat flows, the degree of heating and the temperature of the working surfaces are calculated to predict tool wear and its service life. Based on the parametric non-uniformity of the considered processes, the intensity of oscillations and vibrations of gear cutting machines is predicted, and their impact on the quality of gear surfaces and the accuracy of gears is determined. These approaches enable the study of such processes at the level of individual teeth and blades during cutting. They also allow gear cutting technology and cutting tools to be optimized according to the most important criteria and performance assessments.

  • INVESTIGATION OF GEARS WITH ASYMMETRIC PROFILE USING RELIABILITY PARAMETERS

    by Ihor Hrytsai, Vasyl Verhun

    The results of the study of gears with involute and sinusoidal teeth are presented herein. The subjects of the comparative analysis were the stresses at the root of the tooth from the side of the applied load and from the side of the unloaded profile, contact stresses, and elastic deformations under the action of a given torque. The values of these parameters were determined for a range of pressure angles, from 20° to 40°. To this end, three-dimensional geometric models of the gears of these gearing systems with different pressure angles and asymmetry coefficients were created in SolidWorks. The results of the study showed that, in general, gears with asymmetric teeth have higher parameters than symmetrical gears for all the indicators studied. At the same time, sinusoidal asymmetric gears are superior to involute gears in terms of tooth root stresses, elastic deformations and contact strength. Concurrently, sinusoidal asymmetric gears exhibit superiority over involute gears about tooth root stresses, elastic deformations, and contact strength. It has been demonstrated that gears with a profile described by an asymmetric sinusoidal curve exhibit a higher load capacity, greater resistance to cyclic fatigue, and reduced noise during operation. In summary, these gears will provide better indicators of their operational reliability. In addition, the production of such gears by the radial-circular method is the most efficient, versatile and involves minimal production costs.

  • THEORETICAL FOUNDATIONS OF MODELING AND RESEARCH THE PROCESS OF CUTTING INTERNAL GEAR TEETH MESHING BY THE RADIAL-CIRCULAR METHOD

    by Ihor Hrytsai, Bohdan Stoliar

    The article presents the results of studying the process of cutting cylindrical internal gears by the radial-circular method. The importance and relevance of the task of improving the technology of manufacturing gears and methods of modelling and optimization are substantiated. The advantages, possibilities and scope of the radial-circular method for the production of gears and transmissions are shown. To provide a basis for a comprehensive analysis of the process, a graphical-analytical method has been developed to determine the parameters of chips cut by the teeth of a disk cutter when cutting planetary gears. The regularities of changes in the cut area and chip thickness depending on the gear modulus were investigated. The results made it possible to identify the process features that will affect the cutting force, machining accuracy and tool wear.

  • INFLUENCE OF PROCESS KINEMATICS AND TOOL DESIGN ON GEAR MACHINING BY POWER SKIVING

    by Ihor Hrytsay, Andrii Slipchuk

    The article presents an alternative approach to the description of the cutting scheme, different from the accepted one, which corresponds to the real kinematics of the Power Skiving process. The interpretation of the process is based on the fact that the main cutting movement is the rotational movement of the tool, which, due to the intersection of the axes of the tool and the workpiece, forms the constructive movement of the face in the direction of the axial feed. In this case, the rotation of the workpiece is an auxiliary movement that does not take part in the cutting process, and the movement of the tool imparted to it by the axial feed is insignificant. The direction of the resulting movement of the cutting speed, which corresponds to such a representation, is at a slight angle concerning the face of the gear being cut. This vector determines the values of the actual or working angles on all three blades of the skiving cutter. These angles significantly change the shearing conditions during cutting, the force on the face, and the friction on the flank surfaces. This scheme has been used to analyze the cutting processes using skiving cutters with different blade designs and geometries and also to describe the negative aspects of combined “Super Skiving cutters.”

  • COMPARATIVE ANALYSIS OF INVOLUTE AND SINUSOIDAL GEAR TRANSMISSIONS IN MACHINE DRIVES UNDER CONTACT AND FRICTION CONDITIONS

    by Ihor Hrytsai, Bohdan Stoliar, Serhiy Hromniuk, Sprenergo Limited Liability Company

    The study results of the conditions of contact and friction in two types of gear engagements - involute and sinusoidal - are presented. The main advantages and disadvantages of traditional involute gears are analyzed, and the advantages of sinusoidal gears in some operational parameters of machine drives are noted. It is shown that the sliding speed of the profiles and the amount of contact friction are significantly lower in the sinusoidal mashing. The presented results show that reducing friction in sinusoidal engagement drives reduces power loss by a factor of 1,75 and significantly increases the efficiency of such drives.

  • COMPARATIVE ANALYSIS OF METHODS FOR CUTTING SPUR GEARS BASED ON TECHNICAL AND ECONOMIC PARAMETERS

    by Ihor Hrytsai, Dmytro Herus, Serhii Hromniuk, Ukraine Spr Energo Llc

    The results of the simulation and study of the process of cutting gears by the traditional method of hobbing and the new radial-circular method (RCM), which is carried out by a thin disk cutter, but in the conditions of continuous profile generation, as it is in gear cutting with a hob. It has been shown that due to the peculiarities of this process, its kinematics, and the structure of the disk cutter, RCM is superior to hobbing in all the parameters studied: volumetric productivity, chip thickness ratio, and cutting forces, machining time and machining costs. The higher efficiency of the radial-circular method has thus been demonstrated and the feasibility of its practical application has been confirmed.

  • Open Access

    Simulation of a Power Skiving Gear Cutting Process

    by Ihor Hrytsay, Vadym Stupnytskyy, Andrii Slipchuk

    The results of the computer simulation of the cutting process of gears by the power skiving method are presented. Following the kinematics of the process, a method for generating 3D geometric models of undeformed sheared layers were developed, and their parameters were analyzed. The influence of tool geometry and technological parameters on cutting conditions is investigated. The simulation results and calculation of the tangential force and torque on the tool axis and their influence on the error due to angular elastic deformation of the tool are given.


  • STUDY OF THE GEAR CUTTING PROCESS BY THE RADIAL-CIRCULAR METHOD

    by Ihor Hrytsai, Dmytro Herus

    The results of the study of the radial-circular method of gear cutting are presented. The cutting and shaping of teeth is carried out by a thin disc cutter under conditions of continuous generating, with a combination of axial feed of the cutter and its constructive radial movement due to eccentric installation on the spindle axis. The value of the eccentricity is determined by the gear module. A graph-analytical model was used to calculate the parameters of the cuts, and the cutting force and torque on the cutter axis were modeled using these data. It was found that the cutting process is characterized by significant load variations. The areas of maximum tool wear were predicted. It is shown that for under the same initial conditions, the cutting time using this method is two times less than the time of hobbing. Since a disc cutter can cut gears in a wide range of modules, this process is one of the most versatile. This method opens up great possibilities for the restoration and repair of gears and drives manufactured to standards other than those adopted in Europe.