RCRupesh Chafle

Rupesh Chafle

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Rupesh Chafle has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Numerical Investigation of Deposition Efficiency Influencing Factors in the Friction Surfacing Process

    by Ahmed Elbossily, Zina Kallien, Rupesh Chafle, Kirk A. Fraser, Mohamadreza Afrasiabi, Benjamin Klusemann

    This work presents a numerical study of the friction surfacing process using a GPU-accelerated Smoothed Particle Hydrodynamics (SPH) framework previously validated against experimental observations. The model is employed to examine how thermal boundary conditions, rod diameter, and rod bending angle influence material deposition efficiency and the resulting deposit geometry. Variations in rod diameter are shown to influence both the thermal response and the contact pressure, with smaller rods producing higher efficiency but exhibiting greater process fluctuations. The findings highlight the critical roles of thermal management and geometric configuration in optimizing friction surfacing performance and provide actionable insight for experimental design and process control in solid-state deposition technologies.

  • Open Access

    Numerical simulation of material flow in AA7075 during constrained friction processing

    by George Diyoke, Camila C. de Castro, Rupesh Chafle, Benjamin Klusemann

    Lightweight aluminum alloys, such as AA7075, are desirable for applications in various industries, but their limited formability and workability often pose significant challenges. Constrained Friction Processing (CFP) has emerged as a promising technique to address these challenges by refining microstructures through the relative motion between two tools and the workpiece. The process involves axial extrusion, dual tool rotation, and constraint of the extrudate to control material flow and enhance microstructural refinement. CFP is particularly attractive for high-strength AA7075 as it imposes constrained material flow and increased shear deformation, overcoming the limited formability observed in existing conventional extrusion processes. This study investigates CFP using both experimental and numerical methods, establishing correlations between process conditions, material flow, microstructural evolution, and hardness for the aluminum alloy AA7075. The process was investigated at rotational speeds of 1000–1400 rpm, resulting in the highest measured peak temperature up to 445°C and refined grain sizes of 2–3 µm. The results show that initial shear deformation and material flow under the rotating tools are redistributed during processing, leading to helical flow behavior in the extruded rod. The refined stir zone (SZ) exhibited increase in hardness, about 25% compared to the base material. The developed finite-element model demonstrates good agreement with experimental results with respect to the complete thermal cycle, spatial temperature distribution, and material flow patterns, providing insight into the microstructural evolution during CFP of aluminium alloys.

  • Open Access

    Numerical simulation of friction extrusion: process characteristics and material deformation due to friction

    by George Diyoke, Lars Rath, Rupesh Chafle, Noomane Ben Khalifa, Benjamin Klusemann

    This study employs a finite element thermo-mechanical model, using a Lagrangian incremental setting to investigate friction extrusion (FE) under varying process conditions. The incorporation of rotation in FE generates substantial frictional heat, leading to significantly reduced process forces in comparison to conventional extrusion (CE). The model reveals the interplay between temperature, strain, and strain rate across different microstructural zones of the resulting wire. Specifically, the sticking friction condition in FE enhances initial shear deformation, aligning with a homogeneous spatial strain distribution and predicting complete grain refinement in the extruded wire, as per Zener-Hollomon calculations. On the other hand, under the sliding friction condition in FE, the shear deformation is reduced which results in an inhomogeneous microstructure in the extruded wire. The analysis of material flow in the workpiece reveals distinct transitions from the base material to the thermo-mechanically affected zones. The simulated process force, thermal history, and microstructure during sliding friction conditions align well with the findings from performed friction extrusion experiments.