Jun Xue
Jun Xue has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Changji Wang
National Joint Engineering Research Center for Abrasion Control and Molding of Metal Materials, School of Materials Science and Engineering, Henan University of Science and Technology, Luoyang 471000, China
2 shared publications - Cheng Zhang
National Joint Engineering Research Center for Abrasion Control and Molding of Metal Materials, School of Materials Science and Engineering, Henan University of Science and Technology, Luoyang 471000, China
2 shared publications - Tao Jiang
School of Materials Science and Engineering Henan University of Science and Technology Luoyang China
2 shared publications - Xiaobo Meng
National Joint Engineering Research Center for Abrasion Control and Molding of Metal Materials, School of Materials Science and Engineering, Henan University of Science and Technology, Luoyang 471000, China
2 shared publications - Xiaodong Wang
National Joint Engineering Research Center for Abrasion Control and Molding of Metal Materials, School of Materials Science and Engineering, Henan University of Science and Technology, Luoyang 471000, China
2 shared publications - Ziping Qiao
Science and Technology on Transit Impact Laboratory, No.208 Research Institute of China Ordnance Industries, Beijing 102202, China
2 shared publications
Latest Publications
- Open Access
- 7 November 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (11) , 384
Tribological Properties of 7A04 Aluminum Alloy Enhanced by Ceramic Coating
The 7A04 Al alloy is a commonly used lightweight metal material; however, its low wear resistance limits its application. In this study, the wear resistance of this alloy was improved by preparing micro-arc oxidation (MAO) coatings, MAO/MoS2 composite coatings, and hard-anodized (HA) coatings on its surface. The friction and wear behaviors of these three coatings with diamond-like coated (DLC) rings under oil lubrication conditions were investigated using a ring–block friction tester. The wear rates of the coatings on the block surfaces were determined using laser confocal microscopy, and the wear trajectories of the coatings were examined using scanning electron microscopy. The results indicated that, among the three coatings, the MAO/MoS2 coating had the lowest coefficient of friction of 0.059, whereas the HA coating had the lowest wear rate of 1.47 × 10−6 mm/Nm. The MAO/MoS2 coatings exhibited excellent antifriction properties compared to the other coatings, whereas the HA coatings exhibited excellent anti-wear properties. The porous structure of the MAO coatings stored lubricant and replenished the lubrication film under oil lubrication. Meanwhile, the introduced MoS2 enhanced the densification of the coating and functioned as a solid lubricant. The HA coating exhibited good wear resistance owing to the dense structure of the amorphous-phase aluminum oxide. The mechanisms of abrasive and adhesive wear of the coatings under oil lubrication conditions and the optimization of the tribological properties by the solid–liquid synergistic lubrication effect were investigated. This study provides an effective method for the surface modification of Al alloys with potential applications in the aerospace and automotive industries.
- 7 November 2024
- Published by MDPI AG in Lubricants
- Vol. 12 (11) , 384
Open AccessTribological Properties of 7A04 Aluminum Alloy Enhanced by Ceramic Coating
The 7A04 Al alloy is a commonly used lightweight metal material; however, its low wear resistance limits its application. In this study, the wear resistance of this alloy was improved by preparing micro-arc oxidation (MAO) coatings, MAO/MoS2 composite coatings, and hard-anodized (HA) coatings on its surface. The friction and wear behaviors of these three coatings with diamond-like coated (DLC) rings under oil lubrication conditions were investigated using a ring–block friction tester. The wear rates of the coatings on the block surfaces were determined using laser confocal microscopy, and the wear trajectories of the coatings were examined using scanning electron microscopy. The results indicated that, among the three coatings, the MAO/MoS2 coating had the lowest coefficient of friction of 0.059, whereas the HA coating had the lowest wear rate of 1.47 × 10−6 mm/Nm. The MAO/MoS2 coatings exhibited excellent antifriction properties compared to the other coatings, whereas the HA coatings exhibited excellent anti-wear properties. The porous structure of the MAO coatings stored lubricant and replenished the lubrication film under oil lubrication. Meanwhile, the introduced MoS2 enhanced the densification of the coating and functioned as a solid lubricant. The HA coating exhibited good wear resistance owing to the dense structure of the amorphous-phase aluminum oxide. The mechanisms of abrasive and adhesive wear of the coatings under oil lubrication conditions and the optimization of the tribological properties by the solid–liquid synergistic lubrication effect were investigated. This study provides an effective method for the surface modification of Al alloys with potential applications in the aerospace and automotive industries.
- Open Access
Improving the Wear Resistance Properties of 7A04 Aluminum Alloy with Three Surface Modification Coatings
Multiple advantages, such as good formability, high specific strength, excellent thermal conductivity, and high corrosion resistance, enable aluminum alloy wide application in various fields; however, low surface hardness and poor wear resistance limit its further development. In this study, three surface modification coatings were successfully prepared on the surface of 7A04 aluminum alloy by microarc oxidation (MAO) and a combination of hard anodizing treatment (HA) and physical vapor deposition (PVD), named MAO, HA+W+DLC, and HA+Ti+ta-C, respectively. The microstructure, hardness, and tribological properties of the three coatings and the 7A04 aluminum alloy substrate were studied. The results show that the surface quality and hardness of the coated samples were higher than those of the 7A04 aluminum alloy and that the HA+Ti+ta-C coating possessed the highest hardness of 34.23 GPa. Moreover, the wear resistance of the two multilayer coatings was significantly improved during the ring-block wear tests under oil lubrication, exhibiting a wear rate of 1.51 × 10−7 mm3/N·m for HA+W+DLC and 1.36 × 10−7 mm3/N·m for HA+Ti+ta-C.
Open AccessImproving the Wear Resistance Properties of 7A04 Aluminum Alloy with Three Surface Modification Coatings
Multiple advantages, such as good formability, high specific strength, excellent thermal conductivity, and high corrosion resistance, enable aluminum alloy wide application in various fields; however, low surface hardness and poor wear resistance limit its further development. In this study, three surface modification coatings were successfully prepared on the surface of 7A04 aluminum alloy by microarc oxidation (MAO) and a combination of hard anodizing treatment (HA) and physical vapor deposition (PVD), named MAO, HA+W+DLC, and HA+Ti+ta-C, respectively. The microstructure, hardness, and tribological properties of the three coatings and the 7A04 aluminum alloy substrate were studied. The results show that the surface quality and hardness of the coated samples were higher than those of the 7A04 aluminum alloy and that the HA+Ti+ta-C coating possessed the highest hardness of 34.23 GPa. Moreover, the wear resistance of the two multilayer coatings was significantly improved during the ring-block wear tests under oil lubrication, exhibiting a wear rate of 1.51 × 10−7 mm3/N·m for HA+W+DLC and 1.36 × 10−7 mm3/N·m for HA+Ti+ta-C.