MVMaría Angélica Luján Vega

María Angélica Luján Vega

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


María Angélica Luján Vega has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Renewable Energy Technology: Transient 3D CFD and Experimental Electrical Evaluation of a Cycloidal-Enhanced Rotor Versus a Savonius and Gorlov-Savonius Rotor with Blade Rotation Angle

    by María Angélica Luján Vega, José Eli Eduardo González-Duran, Juan Manuel Olivares-Ramírez, Leonel Estrada Rojo, Jesus Alejandro Franco, Juvenal Rodríguez Reséndiz

    This study presents a numerical and experimental analysis of vertical-axis Cycloidal rotors (RC) versus Savonius rotors (RS), with and without coupling to a Gorlov rotor (RG), designed to operate under low wind speed conditions of 2.5 m/s. Using transient Computational Fluid Dynamics (CFD), numerical mesh stability was evaluated as a function of rotor power, achieving convergence with 8,199,923 nodes and a stable angular momentum after 10 s. In the experimental phase, electrical characterization was conducted by coupling the rotors to a direct current generator, allowing for the determination of the optimal electrical load as a function of rotational speed (RPM). The results show that electrical power output and power coefficient (Cp) increased with rotational speed, reaching a maximum of 39.22 mW and Cp = 0.126 for the Cycloidal rotor (RCθR45), which exhibited the best overall performance. When coupling a Gorlov rotor with a torsion angle of 90° (RGθG90), maximum power of 52.45 mW and Cp = 0.168 were obtained for the hybrid configuration RC,θR0-RGθG90, confirming the aerodynamic and electrical performance improvement due to geometric coupling compared to a standalone Savonius rotor. The comparison between the numerical and experimental results showed consistent trends in Cp values, with slight deviations attributed to friction and alignment effects during physical testing. This study proposes an integrated methodology in renewable energy technologies that combines 3D transient CFD simulation with experimental characterization under variable electrical load conditions to determine the optimal operating power of novel Cycloidal rotors for low-wind-speed applications.

  • Open Access

    Bio-Power Generation in Microbial Fuel Cell with Vermicompost Using Eisenia foetida

    by Adriana Solares Basurto, Mateo Pérez Ruiz, María Angélica Luján Vega, Juan Manuel Olivares-Ramírez, Irma Lucía Vera-Estrada, José Eli Eduardo González-Duran, Juvenal Rodríguez Reséndiz

    This research emphasizes the effect of using Eisenia foetida in vermicompost for power generation in microbial fuel cells (MFCs). By accelerating the organic decomposition, the bioenergy generation is improved. A vermicompost-microbial fuel cell employing electrogenic microorganisms was used to convert chemical energy into electrical energy. In this work, substrates of black soil, tree bark, leaves, eggshells, and ground tomatoes were used. The vermicompost MFC has a copper cathode and a stainless steel anode. In this study, the performance of MFCs was evaluated using different numbers of Eisenia foetida specimens, with three specimens (MFCW3), five specimens (MFCW5), and seven specimens (MFCW7). Our key findings show that by increasing the number of Eisenia foetida specimens does not bring higher power densities; as a result, the best power density was observed in MFCW3 and MFCW5 at the end of the fourth week, both presenting a total of five Eisenia foetida specimens with a power density of 192 mW m−2. Therefore, optimal results were found when 330 g of substrate and five Eisenia foetida specimens were used to achieve a maximum current density of 900 mW m−2 and a maximum power density of 192 mW m−2. This type of microbial fuel cell can be considered as an alternative for power generation with a significantly reduced environmental impact, considering the use of organic waste. It can be considered a game-changer in waste management and bioenergy projects.


  • Open Access

    Experimental and Numerical Analysis of a Novel Cycloid-Type Rotor versus S-Type Rotor for Vertical-Axis Wind Turbine

    by José Eli Eduardo González-Durán, Juan Manuel Olivares-Ramírez, María Angélica Luján-Vega, Juan Emigdio Soto-Osornio, Juan Manuel García-Guendulain, Juvenal Rodriguez-Resendiz

    The performance of a new vertical-axis wind turbine rotor based on the mathematical equation of the cycloid is analyzed and compared through simulation and experimental testing against a semicircular or S-type rotor, which is widely used. The study examines three cases: equalizing the diameter, chord length and the area under the curve. Computational Fluid Dynamics (CFD) was used to simulate these cases and evaluate moment, angular velocity and power. Experimental validation was carried out in a wind tunnel that was designed and optimized with the support of CFD. The rotors for all three cases were 3D printed in resin to analyze their experimental performance as a function of wind speed. The moment and Maximum Power Point (MPP) were determined in each case. The simulation results indicate that the cycloid-type rotor outperforms the semicircular or S-type rotor by 15%. Additionally, experimental evidence confirms that the cycloid-type rotor performs better in all three cases. In the MPP analysis, the cycloid-type rotor achieved an efficiency of 10.8% which was 38% better than the S-type rotor.