Aravinthan Arumugam has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Integrating Finite Element Simulation with Actual GTAW Weld Profiles to Optimize Root Height in Stainless Steel 316L Pipe Joints

    by Mohammad Sohel, Vishal S. Sharma, Aravinthan Arumugam

    Weld root reinforcement is a critical geometric parameter governing stress concentration and structural performance in thin-walled stainless-steel piping systems designed to ASME B31.3. While current codes specify permissible dimensional limits, they do not explicitly quantify how incremental variations in root height influence stress distribution under realistic service loading conditions. This study integrates finite element analysis (FEA) with experimentally validated GTAW weld profiles to evaluate the structural influence of weld root height in 316L stainless-steel pipe joints. An experimentally manufactured 4 in schedule 10S joint with a measured root height of less than 1.5 mm was adopted as the baseline geometry. Additional models with reinforcement heights of 1.138, 2.0, 2.5, and 3.0 mm were evaluated under two representative load cases: (i) internal pressure combined with drag and axial thrust (LC-1), and (ii) internal pressure with thrust only (LC-2). The results demonstrate that reinforcement heights exceeding 2.0 mm increase von Mises, hoop, longitudinal, and radial stress gradients, with peak stresses shifting toward the weld toe under drag-inclusive loading. In contrast, reinforcement ≤2 mm provides smoother load transfer and reduced stiffness discontinuity across the weld interface. The combined numerical and experimental findings support a stress-informed upper limit of 2 mm for weld root reinforcement in thin-walled stainless-steel pipelines, offering a performance-based complement to existing dimensional acceptance criteria.

  • Open Access

    Abrasive Water Jet Machining (AWJM) of Titanium Alloy—A Review

    by Aravinthan Arumugam, Alokesh Pramanik, Amit Rai Dixit, Animesh Kumar Basak

    Abrasive water jet machining (AWJM) is a non-traditional machining process that is increasingly employed for shaping hard-to-machine materials, particularly titanium (Ti)-based alloys such as Ti-6Al-4V. Owing to its non-thermal nature, AWJM enables effective material removal while minimising metallurgical damage and preserving subsurface integrity. The process performance is governed by several interacting parameters, including jet pressure, abrasive type and flow rate, nozzle traverse speed, stand-off distance, jet incident angle, and nozzle design. These parameters collectively influence key output responses such as the material removal rate (MRR), surface roughness, kerf geometry, and subsurface quality. The existing studies consistently report that the jet pressure and abrasive flow rate are directly proportional to MRR, whereas the nozzle traverse speed and stand-off distance exhibit inverse relationships. Nozzle geometry plays a critical role in jet acceleration and abrasive entrainment through the Venturi effect, thereby affecting the cutting efficiency and surface finish. Optimisation studies based on the design of the experiments identify jet pressure and traverse speed as the most significant parameters controlling the surface quality in the AWJM of titanium alloys. Recent research demonstrates the effectiveness of artificial neural networks (ANNs) for process modelling and optimisation of AWJM of Ti-6Al-4V, achieving high predictive accuracy with limited experimental data. This review highlights research gaps in artificial intelligence-based fatigue behaviour prediction, computational fluid dynamics analysis of nozzle wear mechanisms and jet behaviour, and the development of hybrid AWJM systems for enhanced machining performance.


  • Open Access

    Fusion Welding Processes Parameter Optimization for Critical Piping Systems: A Comprehensive Review

    by Mohammad Sohel, Vishal S. Sharma, Aravinthan Arumugam

    Weld quality plays a critical role in ensuring the structural integrity and long-term performance of critical piping systems used across petrochemical, oil and gas, marine, and healthcare sectors. Although gas tungsten arc welding, shielded metal arc welding, and gas metal arc welding are widely applied in pipe fabrication, existing studies often examine these processes independently and provide limited insight into the comparative influence of process parameters on weld morphology, microstructure, and mechanical performance. This review consolidates findings from recent research to evaluate how welding current, arc voltage, heat input, travel speed, shielding gas composition, and joint preparation interact to affect weld bead geometry, heat-affected zone evolution, tensile properties, hardness, and overall weld integrity in piping systems. The primary objective of this review is to critically compare fusion welding process parameter optimization strategies and to identify unresolved challenges in achieving controlled weld root geometry for high-integrity piping applications. Recent industrial failure investigations, particularly in ethylene oxide service piping, further underscore the importance of weld root control. Several documented leak events were traced to excessive root protrusion and inadequate interpretation of non-destructive testing data, where elevated reinforcement disrupted internal flow and promoted turbulence-induced degradation. These recurring issues highlight a broader industry challenge and strengthen the need for improved root-height optimization in critical piping applications. A significant research gap is identified in the limited optimization of weld root reinforcement, particularly in gas tungsten arc welding processes, where most reported studies document root heights exceeding 3 mm. Achieving a root height below 2 mm, which is an important requirement for reducing flow-induced turbulence and meeting industry acceptance criteria, remains insufficiently addressed. This review highlights this gap and outlines future research opportunities involving advanced parameter optimization and improved process monitoring techniques. The synthesis presented here provides a comprehensive reference for enhancing weld quality in critical piping systems and establishes a pathway for next-generation welding strategies aimed at producing high-integrity weld joints compliant with the American Society of Mechanical Engineers B31.3 requirements.


  • Open Access

    An Experimental and Simulation Study on the Effect of Adhesive in Weld Bonded Spot Weld Joints

    by Aravinthan Arumugam, Cosmas Pandit Pagwiwoko, Alokesh Pramanik, Animesh Kumar Basak

    The use of weld bond (WB) joints in automotive manufacturing is gaining popularity for joining similar and dissimilar materials. This study investigated the effect of Sikaflex-252 (Sika Australia Pty Ltd, Perth, Australia) adhesive in DP600 similar steel joints and DP600 and AISI 316 stainless steel dissimilar steel joints. An increase in welding current from 7 kA to 10 kA increased the weld diameter and tensile shear strength in the RSW joints and the WB joints. WB joints had bigger weld diameters of 5.39 mm and 4.84 mm, higher tensile shear strengths of 12.3 kN and 6.85 kN, and higher energy absorption before failure of 32.6 J and 24.6 J at 10 kA compared to joints at 7 kA for similar and dissimilar joints, respectively. The use of adhesive increased heat generation at 10 kA welding current, due to the increase in dynamic resistance. At 7 kA welding current, the adhesive could not produce sufficient heat for spot weld development. The use of adhesive narrowed the weldability lobe in dissimilar RSW and WB joints and showed changes in failure mode. In similar RSW joints and WB joints, weldability lobe changes were not observed, and RSW and WB joints had the same fracture mode for the same welding current. WB welds have reduced stress distribution across the weld nugget compared to RSW welds because of the bigger weld diameter of 5.39 mm and lesser sheet bending of 1.13 mm. WB joint failure comprises the adhesive failure at the start and later the spot weld failure, while RSW joint failure is purely due to spot weld failure.


  • Open Access

    Evaluation of the Parameters Influencing the Results of Non-Destructive Testing Methods for Concrete Strength

    by Ana Evangelista, Aravinthan Arumugam, Mistreselasie Abate

    Non-destructive tests give information about a structure's concrete properties. Still, the reliability of evaluating those properties depends on the experience of the profes-sional who carries out the tests and the curves employed to correlate the measured values with the properties of the investigated concrete. The Non-destructive Test methods (NDT) have been used to evaluate concrete strength in many countries, and experimental studies have investigated which method is more reliable and practical. The concrete properties are estimated/ predicted using correlation curves that combine non-destructive test measurements with the compressive strength of concrete established through a laboratory testing program. Typically, the parameters that influence these curves are the water-to-cement ratio, the type of aggregate, the maximum aggregate size, and the type of cement used in the concrete. This paper presents a study on the influence of different parameters on ultrasonic pulse velocity results and rebound hammer methods. It was found that applying multiple regression to data from two types of non-destructive tests provides a more accurate estimate of compressive strength.


  • Open Access

    Tool Geometries and Design of Friction Stir Spot Welding (FSSW) Tools and Effect on Weld Properties—A Comprehensive Review

    by Aravinthan Arumugam, Animesh Kumar Basak, Alokesh Pramanik, Guy Littlefair

    The incorporation of multi-material design (MMD) to achieve lightweight vehicles requires Friction Stir Spot Welding (FSSW) to join steel with aluminum, magnesium, or composites. This study investigates the mechanisms, challenges, and performance of FSSW in MMD based on the information available in the literature. It also explores the effect of FSSW tool geometries and design on the spot weld formation and mechanical strength. Larger shoulder and pin diameters increase heat generation during welding. A concave shoulder profile produces a stronger weld compared to flat and convex profiles due to its ability to trap materials and transfer materials to the sheet interface efficiently for the development of a sound weld. Grooves such as Fibonacci and involute, and threads on P-FSSW and R-FSSW tools, also contribute to effective material flow during welding, hence assisting in heat generation. This review also provides recommendations on tool design for FSSW, P-FSSW, and R-FSSW.


  • Open Access

    Engineering Perfection in GTAW Welding: Taguchi-Optimized Root Height Reduction for SS316L Pipe Joints

    by Mohammad Sohel, Vishal S. Sharma, Aravinthan Arumugam

    This study presents a systematic optimization of GTAW welding parameters to achieve a pipe-to-pipe butt weld with a root height consistently below 2 mm when joining stainless-steel 316L material, employing the Taguchi design of experiments. To the authors’ knowledge, no similar studies have been conducted to explore the optimization of welding parameters specifically aimed at minimizing weld root height under 2 mm in stainless-steel EO pipeline welding applications. This gap in the existing literature highlights the innovative aspect of the current study, which seeks to address these challenges and improve welding precision and joint reliability. Root height, also referred to as weld root reinforcement, is defined as the excess weld metal protruding beyond the inner surface root side of a butt-welded joint. The input parameters considered are the welding current, voltage, speed, and root gap configurations of 1, 1.5, and 2 mm. Welding was performed according to the Taguchi L-09 experimental design. Nine weld samples were evaluated using liquid penetrant testing to detect surface-breaking defects, such as porosity, laps, and cracks; X-ray radiography to identify internal defects; and profile radiography to assess erosion, corrosion, and root height. Among the nine welded plate samples, the optimal root height (less than 2 mm) was selected and further validated through the welding of a one-pipe sample. An additional macro examination was conducted to confirm the root height and assess the overall root weld integrity and quality.


  • Open Access

    Engineering Perfection in GTAW Welding: Taguchi-Optimized Root Height Reduction for SS316L Pipe Joints

    by Mohammad Sohel, Vishal S Sharma, Aravinthan Arumugam

    This study presents a systematic optimization of GTAW welding parameters to achieve a pipe-to-pipe butt weld with a root height consistently below 2 mm when joining stainless steel 316L material, employing the Taguchi design of experiments. The input parameters considered include GTAW welding current, voltage, welding speed, and root gap configurations of 1 mm, 1.5 mm, and 2 mm. Welding was performed according to the Taguchi L-09 experimental design. All 9 welded samples were evaluated using liquid penetrant testing to detect surface-breaking defects such as porosity, laps, and cracks; X-ray radiography to identify internal defects; and profile radiography to assess erosion, corrosion, and root height. Among the nine welded plate samples, the optimal root height (less than 2 mm) was selected and further validated through the welding of a one-pipe sample. An additional macro examination was conducted to confirm the root height and assess the overall root weld integrity and quality.


  • Open Access

    A Review on the Recent Trends in Forming Composite Joints Using Spot Welding Variants

    by Aravinthan Arumugam, Alokesh Pramanik

    Traditional resistance spot welding (RSW) has been unsuccessful in forming quality composite joints between steel– or aluminum–polymer-based composites. This has led to the development of spot welding variants such as friction stir spot welding (FFSW), ultrasonic spot welding (USW), and laser spot welding (LSW). The paper reviewed the differences in the bonding mechanisms, spot weld characteristics, and challenges involved in using these spot welding variants. Variants of RSW use series electrode arrangement, co-axial electrodes, metallic inserts, interlayers, or external energy to produce composite joints. FFSW and USW use nanoparticles, interlayers, or energy directors to create composite spot welds. Mechanical interlocking is the common composite joint mechanism for all variants. Each spot welding variant has different sets of weld parameters and distinct spot weld morphologies. FFSW is the most expensive variant but is commonly used for composite spot weld joints. USW has a shorter welding cycle compared to RSW and FFSW but can only be used for small components. LSW is faster than the other variants, but limited work was found on its use in composite spot weld joining. The use of interlayers in FFSW and USW to form composite joints is a potential research area recommended in this review.


  • Open Access

    Review on Recent Trends in Composite Joints using Spot Welding Variants

    by Aravinthan Arumugam, Alokesh Pramanik

    Traditional resistance spot welding (RSW) was unsuccessful in forming quality composite joints between steel or aluminium-polymer based composites. This led to the development of spot-welding variants such as friction stir spot welding (FFSW), ultrasonic spot welding (USW) and laser spot welding (LSW). The paper reviewed the differences in the bonding mechanism, spot weld characteristics and challenges involved in using these spot-welding variants. Variants of RSW used series electrodes arrangement, co-axial electrodes, metallic inserts, interlayers or external energy to produce composite joints. FFSW and USW used nanoparticles, interlayers or energy directors to create composite spot welds. Mechanical interlocking is the common composite joint mechanism in all variants. Each spot-welding variant had different sets of weld parameters and distinct spot weld morphologies. FFSW is the most expensive variant but commonly used for composite spot weld joints. USW has a shorter welding cycle compared to RSW and FFSW but can only be used for small components. LSW is faster than the other variants, but limited work was found on its use in composite spot weld joining. Use of interlayers in FFSW and USW to form composite joints are potential research areas recommended in this review.