Petra Mihovilović
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Petra Mihovilović has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Branka Vojnović
Faculty of Textile Technology, University of Zagreb, Prilaz baruna Filipovića 28a, 10000 Zagreb, Croatia
2 shared publications - Ana Pešić
Department of Applied Chemistry, Faculty of Textile Technology, University of Zagreb, Prilaz baruna Filipovića 28a, HR-10000 Zagreb, Croatia
1 shared publication - Mario Cetina
Department of Applied Chemistry, Faculty of Textile Technology, University of Zagreb, Prilaz baruna Filipovića 28a, HR-10000 Zagreb, Croatia
1 shared publication - Nino Dimitrov
Croatian Institute for Public Health, Rockefellerova 7, 10000 Zagreb, Croatia
1 shared publication
Latest Publications
- Open Access
Influence of Ionic Strength and Temperature on the Adsorption of Reactive Black 5 Dye by Activated Carbon: Kinetics, Mechanisms and Thermodynamics
The aim of this work was to investigate the influence of ionic strength and temperature on the adsorption of Reactive Black 5 dye on commercial powdered activated carbon. Adsorption experiments were performed at 45 °C with the addition of NaCl (c0 = 0.01, 0.05, 0.10 and 1.00 M) and Na2SO4 (c0 = 0.01 M). The results were compared with those obtained for both salts (c0 = 0.01 M) at three additional temperatures: 25, 35 and 55 °C. For all adsorption experiments, kinetic and thermodynamic studies were performed. This research showed that the addition of NaCl, even in the concentration of only c0 = 0.01 M, significantly enhanced dye adsorption and that higher NaCl concentration resulted in higher adsorption capacity. In addition, slightly higher adsorption was observed when Na2SO4 was added to the dye solution at the same concentration as NaCl, as well as at a higher temperature, regardless of the salt added to the dye solution. It was also shown that adsorption is kinetically controlled, assuming a pseudo-second-order model, and that intraparticle diffusion is not the only process that influences the adsorption rate. Finally, calculated thermodynamic parameter values for both salts (c0 = 0.01 M) indicate that adsorption was a spontaneous endothermic process.
Open AccessInfluence of Ionic Strength and Temperature on the Adsorption of Reactive Black 5 Dye by Activated Carbon: Kinetics, Mechanisms and Thermodynamics
The aim of this work was to investigate the influence of ionic strength and temperature on the adsorption of Reactive Black 5 dye on commercial powdered activated carbon. Adsorption experiments were performed at 45 °C with the addition of NaCl (c0 = 0.01, 0.05, 0.10 and 1.00 M) and Na2SO4 (c0 = 0.01 M). The results were compared with those obtained for both salts (c0 = 0.01 M) at three additional temperatures: 25, 35 and 55 °C. For all adsorption experiments, kinetic and thermodynamic studies were performed. This research showed that the addition of NaCl, even in the concentration of only c0 = 0.01 M, significantly enhanced dye adsorption and that higher NaCl concentration resulted in higher adsorption capacity. In addition, slightly higher adsorption was observed when Na2SO4 was added to the dye solution at the same concentration as NaCl, as well as at a higher temperature, regardless of the salt added to the dye solution. It was also shown that adsorption is kinetically controlled, assuming a pseudo-second-order model, and that intraparticle diffusion is not the only process that influences the adsorption rate. Finally, calculated thermodynamic parameter values for both salts (c0 = 0.01 M) indicate that adsorption was a spontaneous endothermic process.
- Open Access
- 18 April 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (8) , 3401
Approaches for Sampling and Sample Preparation for Microplastic Analysis in Laundry Effluents
The continuous growth in the production, unsustainable use, and disposal of plastics in recent decades has led to the emergence of a new type of pollutant, microplastics (MPs). In this article, the focus is on the form of MPs, which are produced by the fragmentation of textile fibres during washing processes. The problems associated with the characterisation and quantification of MPs in this type of sample are related to the wide range of concentrations, forms, and degree of degradation as well as physico-chemical and biological properties. Although the basic principles for the analysis of microplastics present in the environmental samples are known, there is the lack of standardised methods for the analysis of MPs in laundry effluents and domestic washing. Therefore, the continuous development of sophisticated analytical techniques and methodologies is required for the reliable collection and isolation, quantification, and characterisation of one of the most challenging analytes. The aim of this review is to outline the key steps of MPs analysis in laundry effluents and domestic washing, focusing on those steps that are underestimated in the current literature: sampling and sample preparation for analysis. Precisely these analytical steps, which can become the main source of analytical measurement system errors, ensure the quality of the analysis. This paper emphasises the importance of monitoring background contamination and presents guidelines to ensure quality control specifically for this type of analyte.
- 18 April 2024
- Published by MDPI AG in Sustainability
- Vol. 16 (8) , 3401
Open AccessApproaches for Sampling and Sample Preparation for Microplastic Analysis in Laundry Effluents
The continuous growth in the production, unsustainable use, and disposal of plastics in recent decades has led to the emergence of a new type of pollutant, microplastics (MPs). In this article, the focus is on the form of MPs, which are produced by the fragmentation of textile fibres during washing processes. The problems associated with the characterisation and quantification of MPs in this type of sample are related to the wide range of concentrations, forms, and degree of degradation as well as physico-chemical and biological properties. Although the basic principles for the analysis of microplastics present in the environmental samples are known, there is the lack of standardised methods for the analysis of MPs in laundry effluents and domestic washing. Therefore, the continuous development of sophisticated analytical techniques and methodologies is required for the reliable collection and isolation, quantification, and characterisation of one of the most challenging analytes. The aim of this review is to outline the key steps of MPs analysis in laundry effluents and domestic washing, focusing on those steps that are underestimated in the current literature: sampling and sample preparation for analysis. Precisely these analytical steps, which can become the main source of analytical measurement system errors, ensure the quality of the analysis. This paper emphasises the importance of monitoring background contamination and presents guidelines to ensure quality control specifically for this type of analyte.