AKAli Kadir

Ali Kadir

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Ali Kadir has a total of 9 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • FINITE ELEMENT STRESS ANALYSIS OF A BUMBLEBEE-INSPIRED MICRO AIR VEHICLE (MAV) WING

    by James Buxton, O. Anwar Bég, Tasveer A. Bég, M. M. Bhatti, S. Kuharat, Ali Kadir, Walid S. Jouri

    A computational study is described of the structural performance of a bumblebee-inspired wing for a Micro Aerial Vehicle (MAV) during the initial downstroke phase of take-off using Finite Element Analysis (FEA). A detailed three-dimensional model of the forewing and hindwing was developed to replicate the morphological and structural features of the insect wing. Static FEA was performed within the ANSYS Workbench to assess stress distribution, strain, and deformation under aerodynamic loading conditions experienced during the first wing stroke, based on a wingspan of 18[ ]mm and the species-specific flapping frequency of 130[ ]Hz. The results indicate that the natural venation pattern of the wing provides effective load distribution, reducing stress concentrations along the wingspan. Peak Von Mises stresses were localized along the leading edge, following the primary branch of the vein structure, while maximum deformation occurred at the wingtip, consistent with experimentally observed honeybee wing deformation. The static pressure case simulations reveal that maximum deformation (total displacement) is observed to consistently decrease with increasing Young’s Modulus. At 2[ ]GPa, the wing exhibits the highest displacement of 1189[ ] [ ]m, and this is strongly reduced to 793[ ] [ ]m at 3[ ]GPa, 595[ ] [ ]m at 4[ ]GPa, and 476[ ] [ ]m at 5[ ]GPa. The Von Mises elastic strain varied significantly with stiffness. The strain decreases when Young’s modulus increases for chitin, with values of [ ] at 2[ ]GPa, [ ] at 3[ ]GPa, [ ] at 4[ ]GPa, and [ ] at 5[ ]GPa. Notably, the Von Mises stress results remained nearly constant across all Young’s Modulus values, hovering around 4.93[ ]MPa. For the acceleration case, at 2[ ]GPa, the maximum total deformation was recorded as 1094[ ] [ ]m. When the modulus was increased to 3[ ]GPa, the displacement reduced to 723[ ] [ ]m, followed by 547[ ] [ ]m at 4[ ]GPa and 438[ ] [ ]m at 5[ ]GPa. As with the static simulation, in all cases, the displacement was concentrated toward the wing tip, with the largest deformation occurring along the outer regions of the bumblebee wing structure, away from the fixed support. Furthermore, the Von Mises strain recorded when the Young’s Modulus was set to 4[ ]GPa exceeds that computed in the other three cases (5, 3, and 2[ ]GPa). As with the static pressure simulations, the Von Mises stress sustains a consistent value across all the Young’s Modulus values, maintaining a peak value of approximately 4.27[ ]MPa. Peak Von Mises stress is observed at the leading edge, where the leading vein changes direction to follow the wing contours, which are most susceptible to loading and are subjected to the highest forces resulting from flight. The findings also demonstrate the potential of biomimetic venation layouts to enhance the strength-to-weight ratio in small-scale UAV wings, thereby supporting efficient lift production with minimal weight penalties.

  • Open Access

    Finite element stress analysis and topological optimization of a commercial aircraft seat structure

    by Christian Amaze, Sireetorn Kuharat, O. Anwar Bég, Ali Kadir, Walid Jouri, Tasveer A. Bég

    In recent years, the Finite Element Method (FEM) has emerged as a cornerstone in the field of seating design, particularly within the aircraft industry. Over the past decade, significant advancements in Finite Element (FE) analysis techniques have revolutionized the seat industry, enabling the creation of safer and more cost-effective seat designs. The accuracy of FE analysis plays a pivotal role in this transformation. In the process of constructing a reliable finite element model, the selection and precise manipulation of key parameters are paramount. These crucial parameters encompass element size, time scale, analysis type, and material model. Properly defining and implementing these parameters ensures that the FE model produces accurate results, closely mirroring real-world performance. Verification of Finite Element Analysis (FEA) results is commonly accomplished through experimental methods. Notably, when the parameters are appropriately integrated into the modelling process, FE analysis outcomes closely align with experimental results. This study aims to leverage the power of FEM in performing static stress analysis and topology optimization of aircraft seats using the SOLIDWORKS commercial finite element platform. By simulating loading conditions, this research calculates static stresses and displacements experienced by the aircraft seat. Through a comprehensive topology optimization study, the weight of the airplane seat is remarkably reduced by up to 30%, while still prioritizing passenger safety. The success of this optimization showcases the potential for substantial weight savings in aircraft seat design without compromising safety standards.