Wen-Ting Qiu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Wen-Ting Qiu has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
Zhou Li
2 shared publicationsHong Zhang
1 shared publication- Qian Lei
State Key Laboratory for Powder Metallurgy Central South University Changsha China
1 shared publication Qiru Wang
1 shared publicationRuizhe Zhang
1 shared publicationShen Gong
1 shared publication
Latest Publications
- 2 July 2024
- Published by Elsevier in Intermetallics
- Vol. 173
Microstructure and properties of high-strength and high-conductivity Cu-2.5Fe-0.2Si-0.3Mg-0.3Cr-0.1Zr-0.2Y alloy
- 2 July 2024
- Published by Elsevier in Intermetallics
- Vol. 173
Microstructure and properties of high-strength and high-conductivity Cu-2.5Fe-0.2Si-0.3Mg-0.3Cr-0.1Zr-0.2Y alloy
- 23 April 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (11)
High‐Strength Wear‐Resistant Cu/Tungsten Carbide/Diamond Composites Fabricated by Powder Metallurgy
Copper‐based diamond composites are widely used for thermal management and wear‐resistant materials. In this work, Cu/diamond, Cu/tungsten carbide (WC)/diamond, and Cu–0.92Cr/WC/diamond composites are fabricated by high‐energy ball milling and rapid hot‐pressing sintering. Physical characteristics, compressive strength, and tribological properties of the studied composites are investigated. The compressive strength of Cu/7wt%WC/diamond composites is 102% higher than the Cu/diamond composites, reaching 415 MPa. Compression fractures extend from the interface due to compression cracks, consistent with the compression curves from molecular dynamics (MD) simulations. The crack propagates from the interface during the compression experiment, which is consistent with the result of MD simulation. The Cu/7wt%WC/diamond composites exhibit a wear rate of 0.6 × 10−6 mm3 (N m)−1 and a friction coefficient of 0.37 at 50 N. The addition of WC and diamond improves the compressive strength and wear resistance. These findings are helpful in the development of copper composites with high compression strength and wear resistance.
- 23 April 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 26 (11)
High‐Strength Wear‐Resistant Cu/Tungsten Carbide/Diamond Composites Fabricated by Powder Metallurgy
Copper‐based diamond composites are widely used for thermal management and wear‐resistant materials. In this work, Cu/diamond, Cu/tungsten carbide (WC)/diamond, and Cu–0.92Cr/WC/diamond composites are fabricated by high‐energy ball milling and rapid hot‐pressing sintering. Physical characteristics, compressive strength, and tribological properties of the studied composites are investigated. The compressive strength of Cu/7wt%WC/diamond composites is 102% higher than the Cu/diamond composites, reaching 415 MPa. Compression fractures extend from the interface due to compression cracks, consistent with the compression curves from molecular dynamics (MD) simulations. The crack propagates from the interface during the compression experiment, which is consistent with the result of MD simulation. The Cu/7wt%WC/diamond composites exhibit a wear rate of 0.6 × 10−6 mm3 (N m)−1 and a friction coefficient of 0.37 at 50 N. The addition of WC and diamond improves the compressive strength and wear resistance. These findings are helpful in the development of copper composites with high compression strength and wear resistance.
- Open Access
- 1 January 2023
- Published by Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences in Acta Physica Sinica
- Vol. 72 (14) , 148102
Phase-field method based simulation of martensitic transformation in porous alloys
相比块体材料,多孔材料中孔洞的存在影响了形状记忆合金马氏体相变的演化过程,包括马氏体变体形貌、分布以及自协调效应。实验结果表明,引入金属-空气界面可以细化马氏体变体组织,从而可提升合金的阻尼性能。本文在实验观察中发现界面周围没有出现马氏体变体的浮凸,且存在非相变组织,认为多孔材料中存在的金属-空气界面并不是自由表面。基于与时间相关的金茨堡-朗道方程构建了不同界面约束下的三维相场模型,研究了多孔材料中约束界面对马氏体变体自协调效应的影响。在金属-空气界面附近模拟得到了细小的马氏体变体自协调形貌,与实验结果一致。在界面约束条件下,体系主要以降低应变能的方式实现总能量的最小化。不同界面条件下的模拟结果表明,提高多孔材料的比表面积是得到更多细小马氏体变体组织的有效手段。
- 1 January 2023
- Published by Acta Physica Sinica, Chinese Physical Society and Institute of Physics, Chinese Academy of Sciences in Acta Physica Sinica
- Vol. 72 (14) , 148102
Open AccessPhase-field method based simulation of martensitic transformation in porous alloys
相比块体材料,多孔材料中孔洞的存在影响了形状记忆合金马氏体相变的演化过程,包括马氏体变体形貌、分布以及自协调效应。实验结果表明,引入金属-空气界面可以细化马氏体变体组织,从而可提升合金的阻尼性能。本文在实验观察中发现界面周围没有出现马氏体变体的浮凸,且存在非相变组织,认为多孔材料中存在的金属-空气界面并不是自由表面。基于与时间相关的金茨堡-朗道方程构建了不同界面约束下的三维相场模型,研究了多孔材料中约束界面对马氏体变体自协调效应的影响。在金属-空气界面附近模拟得到了细小的马氏体变体自协调形貌,与实验结果一致。在界面约束条件下,体系主要以降低应变能的方式实现总能量的最小化。不同界面条件下的模拟结果表明,提高多孔材料的比表面积是得到更多细小马氏体变体组织的有效手段。
- 1 October 2020
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 30 (10) , 2737-2748
Microstructure evolution and hot deformation behavior of Cu−3Ti−0.1Zr alloy with ultra-high strength
- 1 October 2020
- Published by Elsevier in Transactions of Nonferrous Metals Society of China
- Vol. 30 (10) , 2737-2748
Microstructure evolution and hot deformation behavior of Cu−3Ti−0.1Zr alloy with ultra-high strength