Yaxin Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yaxin Wang has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Chengliang Sun
School of Integrated Circuits Hubei Key Laboratory of Electronic Manufacturing and Packaging Integration Wuhan University Wuhan China
4 shared publications - Yan Liu
School of Microelectronics, Wuhan Textile University, Wuhan, China
4 shared publications - Yao Cai
School of Integrated Circuits Hubei Key Laboratory of Electronic Manufacturing and Packaging Integration Wuhan University Wuhan China
4 shared publications - Chaoxiang Yang
Wuhan University
3 shared publications - Chao Gao
The Institute of Technological Sciences, Hubei Key Laboratory of Electronic Manufacturing and Packaging Integration, Wuhan University 1 , Wuhan 430072
2 shared publications - Liangyu Lu
Wuhan University
2 shared publications
Latest Publications
- 1 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (2) , 359-362
Miniaturized ScAlN Bimorph MEMS Microphone With Windmill Structure Achieving 61.2 dB SNR
The demand for compact, lownoise acoustic transducers have motivated rapid advances in MEMS microphone technology. This work presents a high signal-to-noise ratio (SNR) piezoelectric MEMS microphone that utilizes a Sc ${}_{{0}.{1}}$ Al ${}_{{0}.{9}}$ N bimorph diaphragm with a windmill structure, occupying an area of only 0.3721 mm2. The diaphragm consists of four fixed-anchored beams linked by a central hub, which significantly increases the vibration displacement, effective and maximum bending stress. The fixed-anchored beams enable synchronous movement, forming a piston-like vibration mode. Fabricated on an 8-inch thermal-oxide silicon wafer using a 9-mask surface-micromachining process, the device features integrated pad routing and parallel electrical interconnections among segmented piezoelectric elements. Acoustic measurements show that the original and amplified sensitivities at 1 kHz are −70.12 dB and −35.41 dB (re 1 V/Pa), respectively. The microphone achieves an SNR exceeding 61.2 dB over the full audio band, along with a minimum detectable sound pressure of 1 mPa (34 dB SPL) and a resolution of 1 mPa. These performance metrics demonstrate the suitability of the device for low-frequency voice capture and other miniaturized acoustic sensing applications.
- 1 December 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (2) , 359-362
Miniaturized ScAlN Bimorph MEMS Microphone With Windmill Structure Achieving 61.2 dB SNR
The demand for compact, lownoise acoustic transducers have motivated rapid advances in MEMS microphone technology. This work presents a high signal-to-noise ratio (SNR) piezoelectric MEMS microphone that utilizes a Sc ${}_{{0}.{1}}$ Al ${}_{{0}.{9}}$ N bimorph diaphragm with a windmill structure, occupying an area of only 0.3721 mm2. The diaphragm consists of four fixed-anchored beams linked by a central hub, which significantly increases the vibration displacement, effective and maximum bending stress. The fixed-anchored beams enable synchronous movement, forming a piston-like vibration mode. Fabricated on an 8-inch thermal-oxide silicon wafer using a 9-mask surface-micromachining process, the device features integrated pad routing and parallel electrical interconnections among segmented piezoelectric elements. Acoustic measurements show that the original and amplified sensitivities at 1 kHz are −70.12 dB and −35.41 dB (re 1 V/Pa), respectively. The microphone achieves an SNR exceeding 61.2 dB over the full audio band, along with a minimum detectable sound pressure of 1 mPa (34 dB SPL) and a resolution of 1 mPa. These performance metrics demonstrate the suitability of the device for low-frequency voice capture and other miniaturized acoustic sensing applications.
- Open Access
- 25 February 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (8)
Al0.8Sc0.2N film-based BAW filters using transfer process for Wi-Fi6 applications
With the emergence of fifth-generation communication systems, filters with bandwidth (BW) >5% and center frequency >4 GHz are in urgent need. This work presents film bulk acoustic resonators (FBARs) and bulk acoustic wave (BAW) filters based on Al0.8Sc0.2N films. To obtain a better quality AlScN film, we deposited AlScN by physical vaper deposition method on metal-organic chemical vapor deposition developed AlN seed, which was deposited directly on a Si (111) substrate. Using film transfer technology combined with adopting different FBAR structures, filter topology circuits, and external circuits, a BAW filter with a minimum insertion loss of 1.819 dB, a center frequency of 5.56 GHz, a −3 dB BW of 599 MHz, and an out-of-band suppression of at least 35 dB is fabricated and presented in this work.
- 25 February 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (8)
Open AccessAl0.8Sc0.2N film-based BAW filters using transfer process for Wi-Fi6 applications
With the emergence of fifth-generation communication systems, filters with bandwidth (BW) >5% and center frequency >4 GHz are in urgent need. This work presents film bulk acoustic resonators (FBARs) and bulk acoustic wave (BAW) filters based on Al0.8Sc0.2N films. To obtain a better quality AlScN film, we deposited AlScN by physical vaper deposition method on metal-organic chemical vapor deposition developed AlN seed, which was deposited directly on a Si (111) substrate. Using film transfer technology combined with adopting different FBAR structures, filter topology circuits, and external circuits, a BAW filter with a minimum insertion loss of 1.819 dB, a center frequency of 5.56 GHz, a −3 dB BW of 599 MHz, and an out-of-band suppression of at least 35 dB is fabricated and presented in this work.
- 20 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (2) , 836-844
Sc₀.₁Al₀.₉N-Based Bimorph Piezoelectric MEMS Microphones With Tractive Structures
Scandium-doped aluminum nitride (ScAlN) can effectively improve the piezoelectric coefficient; meanwhile, the bimorph obtains a higher sensitivity per unit area than a unimorph structure, thereby greatly improving the sensitivity of MEMS sensors. This article proposes Sc0.1Al0.9N-based bimorph piezoelectric MEMS microphones with tractive structures, which generate a larger high-stress area during operation compared with conventional cantilevers based on finite element method (FEM) simulation and analytical methods. Four electrical connections are designed as components with the tractive structure on the same area of only 0.4679 mm2. The devices are fabricated on a thermal oxide silicon wafer using a nine-mask process. Acoustic measurements show that the maximum unamplified sensitivity is$353.79~\mu $ V/Pa from the combined series-parallel electrical connection, which is 75% higher than the full series electrical connection of$208.27~\mu $ V/Pa. Furthermore, the combined series-parallel electrical connection exhibits grateful performance, where both unamplified and amplified minimum detectable pressure (MDP) are 2 mPa, the signal-to-noise ratio (SNR) is 48.3 dB, and the total harmonic distortion (THD) is only 0.96% at 1 kHz. This work demonstrates a small-size, high-sensitivity piezoelectric MEMS microphone with combined series-parallel connection, which has great commercial value for future scenarios.- 20 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (2) , 836-844
Sc₀.₁Al₀.₉N-Based Bimorph Piezoelectric MEMS Microphones With Tractive Structures
Scandium-doped aluminum nitride (ScAlN) can effectively improve the piezoelectric coefficient; meanwhile, the bimorph obtains a higher sensitivity per unit area than a unimorph structure, thereby greatly improving the sensitivity of MEMS sensors. This article proposes Sc0.1Al0.9N-based bimorph piezoelectric MEMS microphones with tractive structures, which generate a larger high-stress area during operation compared with conventional cantilevers based on finite element method (FEM) simulation and analytical methods. Four electrical connections are designed as components with the tractive structure on the same area of only 0.4679 mm2. The devices are fabricated on a thermal oxide silicon wafer using a nine-mask process. Acoustic measurements show that the maximum unamplified sensitivity is$353.79~\mu $ V/Pa from the combined series-parallel electrical connection, which is 75% higher than the full series electrical connection of$208.27~\mu $ V/Pa. Furthermore, the combined series-parallel electrical connection exhibits grateful performance, where both unamplified and amplified minimum detectable pressure (MDP) are 2 mPa, the signal-to-noise ratio (SNR) is 48.3 dB, and the total harmonic distortion (THD) is only 0.96% at 1 kHz. This work demonstrates a small-size, high-sensitivity piezoelectric MEMS microphone with combined series-parallel connection, which has great commercial value for future scenarios.- Open Access
Design and Fabrication of a Film Bulk Acoustic Wave Filter for 3.0 GHz–3.2 GHz S-Band
Film bulk acoustic-wave resonators (FBARs) are widely utilized in the field of radio frequency (RF) filters due to their excellent performance, such as high operation frequency and high quality. In this paper, we present the design, fabrication, and characterization of an FBAR filter for the 3.0 GHz–3.2 GHz S-band. Using a scandium-doped aluminum nitride (Sc0.2Al0.8N) film, the filter is designed through a combined acoustic–electromagnetic simulation method, and the FBAR and filter are fabricated using an eight-step lithographic process. The measured FBAR presents an effective electromechanical coupling coefficient () value up to 13.3%, and the measured filter demonstrates a −3 dB bandwidth of 115 MHz (from 3.013 GHz to 3.128 GHz), a low insertion loss of −2.4 dB, and good out-of-band rejection of −30 dB. The measured 1 dB compression point of the fabricated filter is 30.5 dBm, and the first series resonator burns out first as the input power increases. This work paves the way for research on high-power RF filters in mobile communication.Open AccessDesign and Fabrication of a Film Bulk Acoustic Wave Filter for 3.0 GHz–3.2 GHz S-Band
Film bulk acoustic-wave resonators (FBARs) are widely utilized in the field of radio frequency (RF) filters due to their excellent performance, such as high operation frequency and high quality. In this paper, we present the design, fabrication, and characterization of an FBAR filter for the 3.0 GHz–3.2 GHz S-band. Using a scandium-doped aluminum nitride (Sc0.2Al0.8N) film, the filter is designed through a combined acoustic–electromagnetic simulation method, and the FBAR and filter are fabricated using an eight-step lithographic process. The measured FBAR presents an effective electromechanical coupling coefficient () value up to 13.3%, and the measured filter demonstrates a −3 dB bandwidth of 115 MHz (from 3.013 GHz to 3.128 GHz), a low insertion loss of −2.4 dB, and good out-of-band rejection of −30 dB. The measured 1 dB compression point of the fabricated filter is 30.5 dBm, and the first series resonator burns out first as the input power increases. This work paves the way for research on high-power RF filters in mobile communication.