ZWZheng Wang

Zheng Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zheng Wang has a total of 29 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Avoiding the Formation of Bubbles and Pits in Buffered Chemical Polishing for the Niobium Superconducting Cavity Through Adjusting the Acid Ratio

    by Zheng Wang, Jinfang Chen, Yue Zong, Shuai Xing, Jiani Wu, Yawei Huang, Xiaowei Wu, Zhejia Xu, Xuhao He, Xiaohu Wang, et al.

    Buffered chemical polishing (BCP) is an important and widely used polishing technique for superconducting radio-frequency (SRF) cavities made of niobium. A common problem encountered during BCP is the formation of bubbles and W-shaped pits on the cavity surface, which may severely limit the RF performance. We report a method to address the problem of W-shaped pits through optimizing the BCP acid ratio. We systematically investigate the effect of the BCP acid ratio through sample and cavity BCP experiments and determine an optimal ratio for the three acids. The new BCP recipe with the optimal acid ratio is verified through the development of niobium cavities with several different shapes, which are shown to be free of pits and demonstrate excellent RF performance; notably, several 3.9 GHz nine-cell cavities present unprecedented accelerating gradients. Furthermore, the findings suggest a simple pit-free BCP recipe that does not require H3PO4, using only HF and HNO3. The method proposed in this study is also appropriate for suppressing pit formation with other acid mixtures or when polishing other metal objects.


  • Open Access

    Mechanism of Pit Formation on Surface of Superconducting Niobium Cavities During Buffered Chemical Polishing

    by Zheng Wang, Jinfang Chen, Yawei Huang, Yue Zong, Shuai Xing, Jiani Wu, Xiaowei Wu, Pengcheng Dong, Runzhi Xia, Xiaohu Wang, et al.

    Superconducting radio-frequency niobium cavities processed using buffered chemical polishing (BCP) sometimes show typical W-shaped pits on their surface, which may greatly limit their performance. However, the causes of such pits and effective solutions are not fully understood. In this study, we reproduced the formation of W-shaped pits on the cavity surface through niobium sample BCP experiments, directly observed the sample surface’s evolution during the polishing process and the polished surface’s morphology, and analyzed the cause of W-shaped pits in detail: the formation and attachment of bubbles on the niobium surface during the BCP process. Then, we systematically investigated the effects of different process parameters on the bubbles and pits, including the acid ratio, temperature, and flow rate. We also investigated how the formation of bubbles and pits was affected by the Nb facing orientation and grain size. This study provides insights into the mechanisms by which bubbles and W-shaped pits are formed on niobium surfaces, and highlights possible directions for reducing pit defects in Nb cavities processed using BCP treatment.


  • Open Access

    Investigation of Electropolishing for High-Gradient 1.3 GHz and 3.9 GHz Niobium Cavities

    by Yue Zong, Jinfang Chen, Dong Wang, Runzhi Xia, Jiani Wu, Zheng Wang, Shuai Xing, Xiaowei Wu, Xuhao He, Xiaohu Wang

    Electropolishing (EP) has become a standard procedure for treating the inner surfaces of superconducting radio-frequency (SRF) cavities composed of pure niobium. In this study, a new EP facility was employed for the surface treatment of both 1.3 GHz and 3.9 GHz single-cell cavities at the Wuxi Platform. The stable “cold EP” mode was successfully implemented on this newly designed EP facility. By integrating the cold EP process with a two-step baking approach, a maximum accelerating gradient exceeding 40 MV/m was achieved in 1.3 GHz single-cell cavities. Additionally, an update to this EP facility involved the design of a special cathode system for small-aperture structures, facilitating the cold EP process for 3.9 GHz single-cell cavities. Ultimately, a maximum accelerating gradient exceeding 25 MV/m was attained in the 3.9 GHz single-cell cavities after undergoing the cold EP treatment. The design and commissioning of the EP device, as well as the electropolishing and vertical test results of the single-cell cavities, will be detailed herein. These methods and experiences are also transferable to multi-cell cavities and elliptical cavities of other frequencies.


  • Open Access

    First Results of Nb3Sn Coated Cavity by Vapor Diffusion Method at SARI

    by Qixin Chen, Yue Zong, Zheng Wang, Shuai Xing, Jiani Wu, Pengcheng Dong, Miyimin Zhao, Xiaowei Wu, Jian Rong, Jinfang Chen

    Nb3Sn is emerging as one of the focal points in superconducting radio frequency (SRF) research, owing to its excellent superconducting properties. These properties hold significant possibilities for cost reduction and the miniaturization of accelerators. In this paper, we report the recent efforts of the Shanghai Advanced Research Institute (SARI) in fabricating high-performance Nb3Sn superconducting cavities using the vapor diffusion method. This includes the construction of a Nb3Sn coating system with dual evaporators and the test results of 1.3 GHz single-cell coated cavities. The coated samples were characterized, and the growth state of the Nb3Sn films was analyzed. The first coated superconducting cavity was tested at both 4.4 K and 2 K, with different cooldown rates passing through the Nb3Sn critical temperatures. The causes of Sn droplet spot defect formation on the surface of the first cavity were analyzed, and such defects were eliminated in the coating of the second cavity by controlling the evaporation rate. This study provides a reference for the preparation of high-performance Nb3Sn-coated cavities using the vapor diffusion method, including the setup of the coating system, the comprehension of the vapor diffusion process, and the test conditions.