GNGuang-Chao Nie

Guang-Chao Nie

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Guang-Chao Nie has a total of 10 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Effects of Cutting Edge Radius on Surface Integrity in Machining of Nickel-Based Cast Superalloy: An In Situ Imaging Approach

    by Guang-Chao Nie, Xiao-Ming Zhang, Zheng-Yan Yang, Dong Zhang, José Outeiro, Hai-Gen Liu, Han Ding

    Cutting edge radius is a crucial factor affecting surface integrity during metal machining, which determines product performance. However, the exact mechanism of how the cutting edge radius affects machined surface has not yet been understood, especially lacking in situ evidence during the material removal process. In this article, effects of cutting edge radius on surface roughness, subsurface deformation, and work hardening of nickel-based cast superalloy are studied through an in situ imaging approach. Based on continuous high-speed filming and digital imaging correlation (DIC) techniques, detailed chip formation and quantitative subsurface plastic deformation under various cutting edge radii are analyzed, and the formation of built-up edge (BUE) is observed when using a large edge radius. Furthermore, when the cutting edge radius is greater than the uncut chip thickness (h), the thickness of plastic deformation increases dramatically. On the other hand, the machined surface roughness can be improved when the cutting edge radius is between 30% and 60% of h. The sharp cutting tools or the cutting edge radius higher than 60% of h result in a poor surface quality on the machined surface during nickel-based cast superalloy machining. The effects of cutting edge radius on machined surface generation are systematically categorized as cutting with chipping, cutting with significant plowing, and cutting with plowing accompanied by BUE formation.


  • A Comprehensive Experiment-Based Approach to Generate Stress Field and Slip Lines in Cutting Process

    by Zheng-Yan Yang, Xiao-Ming Zhang, Guang-Chao Nie, Dong Zhang, Han Ding

    This study proposes a comprehensive experiment-based method to determine stress field and slip lines in metal cutting process. The chip geometry and workpiece's strain and strain rate fields are determined using an in situ imaging technique. The two-dimensional (2D) heat transfer problem for the steady-state cutting process is solved to derive the cutting temperature, and the flow stresses of work material in the main deformation zone are calculated based on the plasticity theory. Furthermore, the stress field is comprehensively determined to satisfy the stress equilibrium, friction law along the tool-chip interface, and traction-free boundary condition along the uncut chip surface. In addition, slip lines in the main deformation zone are derived according to the direction of maximum shear stress without the assumption of perfect rigid-plastic material. The proposed method is validated by comparing the cutting forces calculated based on the obtained stress field with the experimental results.


  • Plastic Strain Threshold Determination for White Layer Formation in Hard Turning of AISI 52100 Steel Using Micro-Grid Technique and Finite Element Simulations

    by Guang-Chao Nie, Ke Zhang, J. C. Outeiro, Serafino Caruso, Domenico Umbrello, Han Ding, Xiao-Ming Zhang

    White layer (WL) formation in metal cutting is generally found to have negative effects on the corrosion and fatigue life of machined components. Nowadays, the mechanism of the WL formation has not been understood very well, especially about the contribution of the thermal and mechanical loadings generated by the cutting process on WL formation. The relationship between subsurface plastic strain caused by mechanical loadings and the formation of WLs is of our concern. To address this issue, WL formation in hard turning of AISI 52100 under dry and cryogenic cooling conditions is investigated by subsurface plastic strain measurement using the micro-grid technique, observed by scanning electron microscope (SEM). Due to the considerable low temperature, WL is mainly generated by the mechanical effect rather than the thermal one, and this hypothesis is supported by physically based finite element method (FEM) simulations. From the investigations, we discover the existing plastic strain threshold, which governs the occurrence of WL in hard turning of AISI 52100 steel under cryogenic cooling conditions.