Azat K. Nurkassimov
Azat K. Nurkassimov has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Aigerim Kh. Shakayeva
The Institute of Nuclear Physics, Ibragimov Str., 1, Almaty, 050032, Kazakhstan
2 shared publications - Alexander Vasilyevich Borisenko
JSC “Park of Nuclear Technologies”, Kurchatova str. 18/1, Kurchatov 071100, Kazakhstan
2 shared publications - Arman B. Yeszhanov
The Institute of Nuclear Physics, Ibragimov Str. 1, Almaty 050032, Kazakhstan
2 shared publications - Ilya V. Korolkov
The Institute of Nuclear Physics
2 shared publications - Maxim Vladimirovich Zdorovets
Engineering Profile Laboratory, L.N. Gumilyov Eurasian National University, Nur-Sultan 010000, Kazakhstan
2 shared publications - Murat Kassymzhanov
Institute of Physical and Technical Sciences, L. N. Gumilyov Eurasian National University, Astana 010008, Kazakhstan
2 shared publications
Latest Publications
- Open Access
- 1 April 2026
- Published by KMG Engineering in Kazakhstan journal for oil & gas industry
- Vol. 8 (1) , 66-78
Radiation-induced crosslinking of polyethylenes under different media for construction and oil & gas applications
Background: Foamed polyethylene is widely used in construction and in the oil and gas industry as a thermal and acoustic insulation material. Its popularity stems from low thermal conductivity, moisture resistance, and chemical stability. However, its durability and long-term performance remain limited. Radiation crosslinking provides an effective modification method by creating a three-dimensional polymer network and improving resistance to degradation. Aim: This study examines the effects of electron beam dose and gas atmosphere (air, argon, nitrogen) on the crosslinking degree of polyethylenes used in construction and oil and gas insulation. Materials and methods: Polyethylene samples irradiated with electron beams at doses of 75, 125, and 175 kGy in three atmospheres: air, argon, and nitrogen. Crosslinking was evaluated through gel fraction analysis following GOST R 59112–2020. Structural changes were characterized by FTIR spectroscopy using Infralum FT-08 (Russia) and Shimadzu IR Spirit (Japan). Results: Maximum crosslinking was observed at 125 kGy. Irradiation in inert atmospheres (argon and nitrogen) yielded higher gel fractions than in air, where degradation processes predominated. findings confirm a direct correlation between irradiation conditions and the structural stability of polyethylene. Conclusion: Radiation crosslinking significantly improves the performance of polyethylene by enhancing its thermal, chemical, and mechanical resistance. This approach can be recommended for producing long-lasting insulation and protective materials in both construction and oil and gas applications.
- 1 April 2026
- Published by KMG Engineering in Kazakhstan journal for oil & gas industry
- Vol. 8 (1) , 66-78
Open AccessRadiation-induced crosslinking of polyethylenes under different media for construction and oil & gas applications
Background: Foamed polyethylene is widely used in construction and in the oil and gas industry as a thermal and acoustic insulation material. Its popularity stems from low thermal conductivity, moisture resistance, and chemical stability. However, its durability and long-term performance remain limited. Radiation crosslinking provides an effective modification method by creating a three-dimensional polymer network and improving resistance to degradation. Aim: This study examines the effects of electron beam dose and gas atmosphere (air, argon, nitrogen) on the crosslinking degree of polyethylenes used in construction and oil and gas insulation. Materials and methods: Polyethylene samples irradiated with electron beams at doses of 75, 125, and 175 kGy in three atmospheres: air, argon, and nitrogen. Crosslinking was evaluated through gel fraction analysis following GOST R 59112–2020. Structural changes were characterized by FTIR spectroscopy using Infralum FT-08 (Russia) and Shimadzu IR Spirit (Japan). Results: Maximum crosslinking was observed at 125 kGy. Irradiation in inert atmospheres (argon and nitrogen) yielded higher gel fractions than in air, where degradation processes predominated. findings confirm a direct correlation between irradiation conditions and the structural stability of polyethylene. Conclusion: Radiation crosslinking significantly improves the performance of polyethylene by enhancing its thermal, chemical, and mechanical resistance. This approach can be recommended for producing long-lasting insulation and protective materials in both construction and oil and gas applications.
- Open Access
Surface Modification of Polyethylene Terephthalate Track-Etched Membranes by 2,2,3,3,4,4,5,5,6,6,7,7-Dodecafluoroheptyl Acrylate for Application in Water Desalination by Direct Contact Membrane Distillation
In this work, the surfaces of poly (ethylene terephthalate) track-etched membranes (PET TeMs) with pore sizes of 670–1310 nm were hydrophobized with 2,2,3,3,4,4,5,5,6,6,7,7-dodecafluoroheptyl acrylate (DFHA) by photoinitiated graft polymerization. Attenuated total reflection FTIR spectroscopy (ATR-FTIR), scanning electron microscopy (SEM) coupled to an energy-dispersive X-ray spectrometer (EDX), and contact angle measurements were used to identify and characterize the TeMs. The optimal parameters for graft polymerization were determined as follows: polymerization time of 60 min, monomer concentration of 30%, and distance from the UV source of 7 cm. The water contact angle of the modified membranes reached 97°, which is 51° for pristine membranes. The modified membranes were tested for water desalination using direct contact membrane distillation (DCMD) method. The effects of membrane pore size, the degree of grafting, and salt concentration on the performance of membrane distillation process were investigated. According to the results obtained, it has been concluded that large pore size hydrophobic TeMs modified by using DFHA could be used for desalinating water.
Open AccessSurface Modification of Polyethylene Terephthalate Track-Etched Membranes by 2,2,3,3,4,4,5,5,6,6,7,7-Dodecafluoroheptyl Acrylate for Application in Water Desalination by Direct Contact Membrane Distillation
In this work, the surfaces of poly (ethylene terephthalate) track-etched membranes (PET TeMs) with pore sizes of 670–1310 nm were hydrophobized with 2,2,3,3,4,4,5,5,6,6,7,7-dodecafluoroheptyl acrylate (DFHA) by photoinitiated graft polymerization. Attenuated total reflection FTIR spectroscopy (ATR-FTIR), scanning electron microscopy (SEM) coupled to an energy-dispersive X-ray spectrometer (EDX), and contact angle measurements were used to identify and characterize the TeMs. The optimal parameters for graft polymerization were determined as follows: polymerization time of 60 min, monomer concentration of 30%, and distance from the UV source of 7 cm. The water contact angle of the modified membranes reached 97°, which is 51° for pristine membranes. The modified membranes were tested for water desalination using direct contact membrane distillation (DCMD) method. The effects of membrane pore size, the degree of grafting, and salt concentration on the performance of membrane distillation process were investigated. According to the results obtained, it has been concluded that large pore size hydrophobic TeMs modified by using DFHA could be used for desalinating water.
- Open Access
- 31 May 2024
- Published by MDPI AG in Preprints.org
Surface Modification of Polyethylene Terephthalate Track-Etched Membranes by 2,2,3,3,4,4,5,5,6,6,7,7- Dodecafluoroheptyl Acrylate for Application in Water Desalination by Direct Contact Membrane Distillation
In this work, the surface of poly(ethylene terephthalate) track-etched membranes (PET TeMs) with pore sizes of 670-1310 nm was hydrophobized with 2,2,3,3,4,4,5,5,6,6,7,7-dodecafluoroheptyl acrylate (DFHA) by photoinitiated graft polymerization. Attenuated total reflection FTIR spec-troscopy (ATR-FTIR), scanning electron microscopy (SEM) coupled to an energy-dispersive X-ray spectrometer (EDX), and contact angle measurement were used to identify and characterize the TeMs. The optimal parameters for graft polymerization were determined as follows: polymeriza-tion time 60 min, monomer concentration of 30% and distance from the UV-source 7 cm. The wa-ter contact angle of the modified membranes reached 97° which is 51o for pristine membranes. The modified membranes were tested for water desalination using direct contact membrane distillation (DCMD) method. The effect of membrane pore size, the degree of grafting and salt concentration on the performance of membrane distillation process was investigated. According to the results obtained, it has been concluded that large pore size hydrophobic TeMs modified by using DFHA could be used for desalinating water.
- 31 May 2024
- Published by MDPI AG in Preprints.org
Open AccessSurface Modification of Polyethylene Terephthalate Track-Etched Membranes by 2,2,3,3,4,4,5,5,6,6,7,7- Dodecafluoroheptyl Acrylate for Application in Water Desalination by Direct Contact Membrane Distillation
In this work, the surface of poly(ethylene terephthalate) track-etched membranes (PET TeMs) with pore sizes of 670-1310 nm was hydrophobized with 2,2,3,3,4,4,5,5,6,6,7,7-dodecafluoroheptyl acrylate (DFHA) by photoinitiated graft polymerization. Attenuated total reflection FTIR spec-troscopy (ATR-FTIR), scanning electron microscopy (SEM) coupled to an energy-dispersive X-ray spectrometer (EDX), and contact angle measurement were used to identify and characterize the TeMs. The optimal parameters for graft polymerization were determined as follows: polymeriza-tion time 60 min, monomer concentration of 30% and distance from the UV-source 7 cm. The wa-ter contact angle of the modified membranes reached 97° which is 51o for pristine membranes. The modified membranes were tested for water desalination using direct contact membrane distillation (DCMD) method. The effect of membrane pore size, the degree of grafting and salt concentration on the performance of membrane distillation process was investigated. According to the results obtained, it has been concluded that large pore size hydrophobic TeMs modified by using DFHA could be used for desalinating water.