Sandy Atanalian
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Sandy Atanalian has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Kamal Al-Haddad
GREPCI) Ecole de Technologie Suprieure, ETS,Department of electrical engineering,Montral,Canada
5 shared publicationsRawad Zgheib
Institut de recherche dHydro-Qubec (IREQ), Hydro-Qubec,Varennes,Québec,Canada
4 shared publicationsHadi Y. Kanaan
Faculty of engineering (ESIB), Saint-Joseph University of Beirut, Beirut, Lebanon
3 shared publications- Kamal Al-Haddad
Department of Ecole de Technologie Superieure, University of Quebec, Montreal, QC, Canada
3 shared publications - Rawad Zgheib
Institut de Recherche dHydro-Qubec (IREQ), Varennes, QC, Canada
3 shared publications Fadia Sebaaly
Institut de recherche dHydro-Qubec (IREQ), Hydro-Qubec,Varennes,Québec,Canada
2 shared publications
Latest Publications
- Open Access
- 30 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 78795-78807
Z Packed U-Cell Modular Multilevel Converter for STATCOM Applications
The Modular Multilevel Converter (MMC) is a promising topology for STATCOM applications due to its key features, such as modularity, scalability, and reduced harmonic content. Increasing the number of voltage levels in MMC reduces harmonics but simultaneously increases the number of submodules (SMs) per arm, leading to larger sizes and higher costs, which presents a challenge. To address this, this article introduces a novel 17-level MMC-STATCOM based on the Z Packed U-Cell (ZPUC) converter as its SM, which enables the generation of more voltage levels with fewer components and reduced harmonic content, offering significant advantages in terms of size and cost. Given the complex structure of the proposed converter and the associated challenges in building a physical prototype, real-time (RT) simulation using FPGA technology is employed for validation. The key contributions include integrating the ZPUC-SM into a three-phase STATCOM for the first time and adapting the converter model and its control system to RT tools, including RT-LAB with an electric hardware solver for FPGA execution. In addition, capacitor voltage balancing and energy sorting algorithms are integrated within Phase-Shift Pulse Width Modulation, eliminating the need for an additional controller while maintaining the floating capacitors of ZPUC-SMs balanced and regulated. The specifications of the proposed converter are defined, the mathematical model and control system are derived, and a real-time implementation based on CPU and FPGA execution is built to verify the scheme. The obtained RT simulation results provide practical evidence confirming the effective operation of the proposed scheme in VAR compensation mode.
- 30 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 78795-78807
Open AccessZ Packed U-Cell Modular Multilevel Converter for STATCOM Applications
The Modular Multilevel Converter (MMC) is a promising topology for STATCOM applications due to its key features, such as modularity, scalability, and reduced harmonic content. Increasing the number of voltage levels in MMC reduces harmonics but simultaneously increases the number of submodules (SMs) per arm, leading to larger sizes and higher costs, which presents a challenge. To address this, this article introduces a novel 17-level MMC-STATCOM based on the Z Packed U-Cell (ZPUC) converter as its SM, which enables the generation of more voltage levels with fewer components and reduced harmonic content, offering significant advantages in terms of size and cost. Given the complex structure of the proposed converter and the associated challenges in building a physical prototype, real-time (RT) simulation using FPGA technology is employed for validation. The key contributions include integrating the ZPUC-SM into a three-phase STATCOM for the first time and adapting the converter model and its control system to RT tools, including RT-LAB with an electric hardware solver for FPGA execution. In addition, capacitor voltage balancing and energy sorting algorithms are integrated within Phase-Shift Pulse Width Modulation, eliminating the need for an additional controller while maintaining the floating capacitors of ZPUC-SMs balanced and regulated. The specifications of the proposed converter are defined, the mathematical model and control system are derived, and a real-time implementation based on CPU and FPGA execution is built to verify the scheme. The obtained RT simulation results provide practical evidence confirming the effective operation of the proposed scheme in VAR compensation mode.
- Open Access
- 4 June 2024
- Published by MDPI AG in Electronics
- Vol. 13 (11) , 2186
Real-Time Implementation of Three-Phase Z Packed U-Cell Modular Multilevel Grid-Connected Converter Using CPU and FPGA
The Modular Multilevel Converter (MMC) is a promising converter for medium-/high voltage applications due to its various features. The waveform quality could be enhanced further by expanding the number of generated voltage levels, which increases the number of submodules (SMs); however, this improvement enlarges the size and cost of the converter, posing a persistent challenge. Hence, there exists a trade-off between power quality and the size and complexity of the converter. To verify the performance of such a complex converter and to validate the effectiveness of the control system, especially in the absence of a physical system, Real-Time (RT) simulation becomes crucial. However, the large number of components of a MMC creates important numerical challenges and computational difficulties in RT simulation. This paper proposes a grid-connected MMC employing a Z Packed U-Cell converter as a SM to generate a higher number of voltage levels while minimizing the required number of SMs. The ZPUC-MMC is implemented on an FPGA-based RT simulation platform using Electric Hardware Solver to reduce computational burden and simulation time, while improving the accuracy of the obtained results. Conventional controllers of MMCs are applied to assess the effectiveness and robustness of the proposed system during steady-state and dynamic operations.
- 4 June 2024
- Published by MDPI AG in Electronics
- Vol. 13 (11) , 2186
Open AccessReal-Time Implementation of Three-Phase Z Packed U-Cell Modular Multilevel Grid-Connected Converter Using CPU and FPGA
The Modular Multilevel Converter (MMC) is a promising converter for medium-/high voltage applications due to its various features. The waveform quality could be enhanced further by expanding the number of generated voltage levels, which increases the number of submodules (SMs); however, this improvement enlarges the size and cost of the converter, posing a persistent challenge. Hence, there exists a trade-off between power quality and the size and complexity of the converter. To verify the performance of such a complex converter and to validate the effectiveness of the control system, especially in the absence of a physical system, Real-Time (RT) simulation becomes crucial. However, the large number of components of a MMC creates important numerical challenges and computational difficulties in RT simulation. This paper proposes a grid-connected MMC employing a Z Packed U-Cell converter as a SM to generate a higher number of voltage levels while minimizing the required number of SMs. The ZPUC-MMC is implemented on an FPGA-based RT simulation platform using Electric Hardware Solver to reduce computational burden and simulation time, while improving the accuracy of the obtained results. Conventional controllers of MMCs are applied to assess the effectiveness and robustness of the proposed system during steady-state and dynamic operations.
- 4 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Modular Multilevel Converters for Fast Charging Stations of Electric Vehicles: An Overview
This paper reviews the different configurations of Modular Multilevel Converters (MMCs) used in Fast Charging Stations (FCSs) and Extreme Fast Charging Stations (XFCs) of Electric Vehicles (EVs), It enables a solid reference for charging stations operating at the megawatt's level and employing novel topologies to interface with the grid. First, the paper delivers a general overview on FCSs and XFCs along with their requirements and challenges. Then, the paper describes in detail the different configurations of MMC structure and highlights the importance of using MMC in terms of reducing the overall size of the charging station, and in reducing the impact of the massive integration of FCSs and XFCs on the grid. A comparative study is presented to focus on various configurations of MMC-based FCSs and XFCs and compares them in a table in terms of structure components, target objectives within the structure, and outcomes benefits of each type. Common benefit associated with several proposed MMC configurations is interfacing directly with the medium voltage grid, thus the bulky, costly, and heavy line frequency transformer is removed. Additional benefits include limiting the grid-side filter due to the high-quality waveforms of MMC, in addition to the easy integration of renewable energy sources and energy storage systems which helps in managing the impact of the charging station on the grid in terms of power requirement.
- 4 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Modular Multilevel Converters for Fast Charging Stations of Electric Vehicles: An Overview
This paper reviews the different configurations of Modular Multilevel Converters (MMCs) used in Fast Charging Stations (FCSs) and Extreme Fast Charging Stations (XFCs) of Electric Vehicles (EVs), It enables a solid reference for charging stations operating at the megawatt's level and employing novel topologies to interface with the grid. First, the paper delivers a general overview on FCSs and XFCs along with their requirements and challenges. Then, the paper describes in detail the different configurations of MMC structure and highlights the importance of using MMC in terms of reducing the overall size of the charging station, and in reducing the impact of the massive integration of FCSs and XFCs on the grid. A comparative study is presented to focus on various configurations of MMC-based FCSs and XFCs and compares them in a table in terms of structure components, target objectives within the structure, and outcomes benefits of each type. Common benefit associated with several proposed MMC configurations is interfacing directly with the medium voltage grid, thus the bulky, costly, and heavy line frequency transformer is removed. Additional benefits include limiting the grid-side filter due to the high-quality waveforms of MMC, in addition to the easy integration of renewable energy sources and energy storage systems which helps in managing the impact of the charging station on the grid in terms of power requirement.
- 4 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Voltage Balancing and Energy Sorting of 17L-ZPUC-Based Modular Multilevel Converter
Z Packed U-Cell (ZPUC) converter is a novel multilevel topology that was proposed for both single-/three-phase applications and Modular Multilevel Converter (MMC) configurations. MMC is a promising topology that gained a lot of interest in the medium-/high-voltage applications due to its various features such as modularity, scalability, and reduced harmonic contents. In MMC, increasing the number of submodule (SM) per arm increases the number of generated voltage levels and results in obtaining better quality waveforms but on the expense of increasing the overall components count. However, with ZPUC-MMC a higher number of voltage levels could be generated with a reduced number of SM and then with a reduced component count. In addition, ZPUC-MMC features a fully integrated voltage balancing (VB) algorithm within the Phase-Shift Pulse Width Modulation technique, thus no additional controller is required. This paper details the integrated VB and energy sorting algorithms of ZPUC-MMC employing two ZPUC-SM in each arm. The performance of the converter along with the VB are validated with MATLAB/SIMULINK. 17 level (17L-) phase voltages are generated while the flying capacitors of each ZPUC-SM are fully balanced and regulated.
- 4 April 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-4
Voltage Balancing and Energy Sorting of 17L-ZPUC-Based Modular Multilevel Converter
Z Packed U-Cell (ZPUC) converter is a novel multilevel topology that was proposed for both single-/three-phase applications and Modular Multilevel Converter (MMC) configurations. MMC is a promising topology that gained a lot of interest in the medium-/high-voltage applications due to its various features such as modularity, scalability, and reduced harmonic contents. In MMC, increasing the number of submodule (SM) per arm increases the number of generated voltage levels and results in obtaining better quality waveforms but on the expense of increasing the overall components count. However, with ZPUC-MMC a higher number of voltage levels could be generated with a reduced number of SM and then with a reduced component count. In addition, ZPUC-MMC features a fully integrated voltage balancing (VB) algorithm within the Phase-Shift Pulse Width Modulation technique, thus no additional controller is required. This paper details the integrated VB and energy sorting algorithms of ZPUC-MMC employing two ZPUC-SM in each arm. The performance of the converter along with the VB are validated with MATLAB/SIMULINK. 17 level (17L-) phase voltages are generated while the flying capacitors of each ZPUC-SM are fully balanced and regulated.
- 17 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Three-Phase ZPUC-MMC Grid Connected Converter
Modular Multilevel Converter (MMC) is a promising topology that gained lot of interest in medium-voltage grid-connected applications due to its modularity, scalability, and adaptability. Although increasing the number of submodules per arm leads to a higher number of voltage levels and better waveforms quality, the size and then the cost of the converter remains a challenge. Therefore, a trade-off between topology complexity and power quality exists. This paper proposes an MMC based on Z Packed U-Cell converter as Submodule (ZPUC-SM) to generate a higher number of voltage levels with reduced number of SMs. When compared to HB-MMC, this topology features reduced components count for generating the same voltage levels. Thus, the candidate topology is considered to be a promising solution for medium-voltage applications connecting the utility. This paper details the design, modeling and control of ZPUC-MMC operating as a three-phase grid-connected converter. The controller task is to regulate output current to fulfill grid connectivity requirements. A Phase shifted-PWM with an integrated voltage balancing algorithm takes in action of controlling the three-capacitors voltages of each arm. Thus, no additional voltage controllers are required. The performance of the proposed converter along with its control system are validated with MATLAB/SIMULINK, and the simulation results validate the robustness and effectiveness of the proposed control during both steady-state and dynamic operations.
- 17 October 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Three-Phase ZPUC-MMC Grid Connected Converter
Modular Multilevel Converter (MMC) is a promising topology that gained lot of interest in medium-voltage grid-connected applications due to its modularity, scalability, and adaptability. Although increasing the number of submodules per arm leads to a higher number of voltage levels and better waveforms quality, the size and then the cost of the converter remains a challenge. Therefore, a trade-off between topology complexity and power quality exists. This paper proposes an MMC based on Z Packed U-Cell converter as Submodule (ZPUC-SM) to generate a higher number of voltage levels with reduced number of SMs. When compared to HB-MMC, this topology features reduced components count for generating the same voltage levels. Thus, the candidate topology is considered to be a promising solution for medium-voltage applications connecting the utility. This paper details the design, modeling and control of ZPUC-MMC operating as a three-phase grid-connected converter. The controller task is to regulate output current to fulfill grid connectivity requirements. A Phase shifted-PWM with an integrated voltage balancing algorithm takes in action of controlling the three-capacitors voltages of each arm. Thus, no additional voltage controllers are required. The performance of the proposed converter along with its control system are validated with MATLAB/SIMULINK, and the simulation results validate the robustness and effectiveness of the proposed control during both steady-state and dynamic operations.
- 8 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 43-48
A Review on Electric Vehicles Battery Chargers and AC/DC Converters for Fast Charging Stations
This paper illustrates a review on Electric Vehicles battery chargers that could be compared and classified according to several categories. The study focuses on the fast charging stations, that are off-board chargers, and more specifically on bidirectional AC/DC converters that constitute an integral part of the fast charging station. AC/DC converters interface with the grid and the DC/DC converters, and they must satisfy the grid requirements and specifications. Moreover, this paper points up the problems associated with conventional two-levels AC/DC converters and highlights the importance of using multilevel converters instead.
- 8 December 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 43-48
A Review on Electric Vehicles Battery Chargers and AC/DC Converters for Fast Charging Stations
This paper illustrates a review on Electric Vehicles battery chargers that could be compared and classified according to several categories. The study focuses on the fast charging stations, that are off-board chargers, and more specifically on bidirectional AC/DC converters that constitute an integral part of the fast charging station. AC/DC converters interface with the grid and the DC/DC converters, and they must satisfy the grid requirements and specifications. Moreover, this paper points up the problems associated with conventional two-levels AC/DC converters and highlights the importance of using multilevel converters instead.
- 18 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2327-2332
Bidirectional Electric Vehicle Battery Charger Assisted by Photovoltaic Panels
In this paper, a bidirectional power electronics converter assisted by Photovoltaic Panels for Electric Vehicle battery charging application is presented. The charger is composed of two conversion stages: an AC/DC converter represented by an active-rectifier, and a DC/DC converter illustrated by a Dual Active Bridge. The solar renewable energy is considered an alternative DC source assisting in charging the battery. The charger is tested using MATLAB/SIMULINK under different charging and discharging scenarios. An Electric Vehicle equipped with a bidirectional battery charging system has the ability to act as source or a load.
- 18 October 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2327-2332
Bidirectional Electric Vehicle Battery Charger Assisted by Photovoltaic Panels
In this paper, a bidirectional power electronics converter assisted by Photovoltaic Panels for Electric Vehicle battery charging application is presented. The charger is composed of two conversion stages: an AC/DC converter represented by an active-rectifier, and a DC/DC converter illustrated by a Dual Active Bridge. The solar renewable energy is considered an alternative DC source assisting in charging the battery. The charger is tested using MATLAB/SIMULINK under different charging and discharging scenarios. An Electric Vehicle equipped with a bidirectional battery charging system has the ability to act as source or a load.
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 4706-4711
PV Assisted EV Charging in DC Micro-Grids
The integration of renewable energies as dc power sources is increasing in dc micro-grid that is gaining more importance than ac micro-grid because it requires fewer conversion stages. Also electrification through electric vehicles (EV) is encouraged due to their reduced fuel usage and greenhouse emission. In this paper, the integration of solar energy through photovoltaic panels (PV) in dc micro-grids as an assisted approach for EV charging is presented. EV has the ability to operate as electric source or load. In Vehicle to grid technology (V2G), EV can transfer the energy stored in its battery back to the Grid.
- 1 October 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 1, 4706-4711
PV Assisted EV Charging in DC Micro-Grids
The integration of renewable energies as dc power sources is increasing in dc micro-grid that is gaining more importance than ac micro-grid because it requires fewer conversion stages. Also electrification through electric vehicles (EV) is encouraged due to their reduced fuel usage and greenhouse emission. In this paper, the integration of solar energy through photovoltaic panels (PV) in dc micro-grids as an assisted approach for EV charging is presented. EV has the ability to operate as electric source or load. In Vehicle to grid technology (V2G), EV can transfer the energy stored in its battery back to the Grid.