Babatunde Adebayo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Babatunde Adebayo has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- A. O. Omoseebi
Federal University of Technology
1 shared publication - Adams Abiodun Akinlabi
Department of Mining Engineering, Federal University of Technology, Akure, Nigeria
1 shared publication - Alexander Orunduyi
Federal University of Technology
1 shared publication - Blessing Olamide Taiwo
Department of Mining Engineering, Federal University of Technology, Akure, Nigeria
1 shared publication - Damilola J. Afu
Federal University of Technology
1 shared publication J.G.M. Mukoya
University of Namibia Department of Mining and Metallurgical Engineering
1 shared publication
Latest Publications
- 12 February 2026
- Published by Trans Tech Publications, Ltd. in Engineering Headway
- Vol. 33, 103-110
Evaluation of Abrasive Properties of Selected Granite Rocks and Their Effects on Button Bit Wear
Abrasive properties of selected rocks and their influence on button bit wear were investigated. Rock samples were obtained from three locations in Southwest, Nigeria. These samples were tested in the laboratory for grain size and circularity factor. Also, porosity, Equivalent Quartz content (EQC), Rock Hardness Number (RHN), Rock Abrasivity Index (RAI) and Uniaxial Compressive Strength were determined. Bit button lengths consumed were measured at regular interval as drilling operation progresses. Results of grain size revealed that medium feldspar granite has least average grain size varying from 0.12 – 0.14 mm. There is possibility that rate of drilling may be low while drilling through this rock. The values of circularity factor varied from 0.624 for medium feldspar granite to 0.786 for coarse muscovite granite . The mean values of porosity varied from between 0.85 and 1.33% for medium feldspar granite and coarse muscovite granite respectively. Biotite hornblende granite has the highest mean uniaxial compressive strength value of 119.48 MPa while coarse muscovite granite has the least mean value of 90.65 MPa. The values of free silica, EQC, RHN, and RAI varied from 35.93 – 51.35%, 45.60 – 67.21%, 575.52 – 821.64 kg/mm 3 and 4133.64 – 7003.71 respectively. It was observed that grain size affects the void size in these rocks, which accounted for least porosity value obtained in medium feldspar granite . Average bit button length consumed varied from 15.56 – 24.54 mm for gauge button while length of centre button varied from 13.00 – 19.61 mm. Higher gauge button length consumption could be inferred that it effects the cutting, crushing and wedging of rock mineral components at rock-bit interface. The understanding of grain size, circularity factor and abrasive properties will provide adequate information for quarry to select appropriate bit and drilling machine.
- 12 February 2026
- Published by Trans Tech Publications, Ltd. in Engineering Headway
- Vol. 33, 103-110
Evaluation of Abrasive Properties of Selected Granite Rocks and Their Effects on Button Bit Wear
Abrasive properties of selected rocks and their influence on button bit wear were investigated. Rock samples were obtained from three locations in Southwest, Nigeria. These samples were tested in the laboratory for grain size and circularity factor. Also, porosity, Equivalent Quartz content (EQC), Rock Hardness Number (RHN), Rock Abrasivity Index (RAI) and Uniaxial Compressive Strength were determined. Bit button lengths consumed were measured at regular interval as drilling operation progresses. Results of grain size revealed that medium feldspar granite has least average grain size varying from 0.12 – 0.14 mm. There is possibility that rate of drilling may be low while drilling through this rock. The values of circularity factor varied from 0.624 for medium feldspar granite to 0.786 for coarse muscovite granite . The mean values of porosity varied from between 0.85 and 1.33% for medium feldspar granite and coarse muscovite granite respectively. Biotite hornblende granite has the highest mean uniaxial compressive strength value of 119.48 MPa while coarse muscovite granite has the least mean value of 90.65 MPa. The values of free silica, EQC, RHN, and RAI varied from 35.93 – 51.35%, 45.60 – 67.21%, 575.52 – 821.64 kg/mm 3 and 4133.64 – 7003.71 respectively. It was observed that grain size affects the void size in these rocks, which accounted for least porosity value obtained in medium feldspar granite . Average bit button length consumed varied from 15.56 – 24.54 mm for gauge button while length of centre button varied from 13.00 – 19.61 mm. Higher gauge button length consumption could be inferred that it effects the cutting, crushing and wedging of rock mineral components at rock-bit interface. The understanding of grain size, circularity factor and abrasive properties will provide adequate information for quarry to select appropriate bit and drilling machine.
- 11 June 2024
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series D
- Vol. 106 (2) , 1245-1259
Enhancing Rock Fragmentation in Mining: Leveraging Ensemble Classification Machine Learning Algorithms for Blast Toe Volume Assessment
- 11 June 2024
- Published by Springer Nature in Journal of The Institution of Engineers (India): Series D
- Vol. 106 (2) , 1245-1259
Enhancing Rock Fragmentation in Mining: Leveraging Ensemble Classification Machine Learning Algorithms for Blast Toe Volume Assessment
- Open Access
- 1 January 2019
- Published by Academy of Science of South Africa in Journal of the Southern African Institute of Mining and Metallurgy
- Vol. 119 (5) , 459-464
Rock properties and machine parameters evaluation at Rössing Uranium Mine for optimum drill performance
This work was carried out to determine the influence of rock properties and drilling machine parameters on the penetration rate at the SJ pit of Rössing Uranium Mine, Namibia. Rock properties (uniaxial compressive strength, tensile strength, and modulus of elasticity) of samples collected were determined in the laboratory. Drilling experiments were conducted in which feed pressure, air pressure, rotary speed, weight on the bit, and torque were varied to measure their effect on the penetration rate. The uniaxial compressive strength varied from 90-180 MPa for layered marble-quartzite and banded gneiss. Increases in feed pressure, weight on the bit, and rotary speed beyond the optimum level led to a decrease in penetration rate and caused the drill bit to 'stall'. Results of the study revealed that penetration rate increases with an increase in the feed pressure and air pressure. After reaching a maximum value, the penetration rate begins to decrease despite increasing feed pressure. A very high torque causes the drill bit to stall, since the feed pressure is too high and the air pressure is not sufficient to remove the cuttings from blast-hole at maxium bailing velocities. The average penetration rate varied from 19 to 45 m/h for phase 2 of the pit, and from 17 to 68 m/h for phase 3. The optimum drilling machine parameters obtained in phase 2 and phase 3 were slightly lower than those currently being used at the mine. The trials of the optimum machine parameters will assist in reducing the cost of drilling, which varied from N$29.48 to N$36.31 per metre for the tricone bit.
- 1 January 2019
- Published by Academy of Science of South Africa in Journal of the Southern African Institute of Mining and Metallurgy
- Vol. 119 (5) , 459-464
Open AccessRock properties and machine parameters evaluation at Rössing Uranium Mine for optimum drill performance
This work was carried out to determine the influence of rock properties and drilling machine parameters on the penetration rate at the SJ pit of Rössing Uranium Mine, Namibia. Rock properties (uniaxial compressive strength, tensile strength, and modulus of elasticity) of samples collected were determined in the laboratory. Drilling experiments were conducted in which feed pressure, air pressure, rotary speed, weight on the bit, and torque were varied to measure their effect on the penetration rate. The uniaxial compressive strength varied from 90-180 MPa for layered marble-quartzite and banded gneiss. Increases in feed pressure, weight on the bit, and rotary speed beyond the optimum level led to a decrease in penetration rate and caused the drill bit to 'stall'. Results of the study revealed that penetration rate increases with an increase in the feed pressure and air pressure. After reaching a maximum value, the penetration rate begins to decrease despite increasing feed pressure. A very high torque causes the drill bit to stall, since the feed pressure is too high and the air pressure is not sufficient to remove the cuttings from blast-hole at maxium bailing velocities. The average penetration rate varied from 19 to 45 m/h for phase 2 of the pit, and from 17 to 68 m/h for phase 3. The optimum drilling machine parameters obtained in phase 2 and phase 3 were slightly lower than those currently being used at the mine. The trials of the optimum machine parameters will assist in reducing the cost of drilling, which varied from N$29.48 to N$36.31 per metre for the tricone bit.