AOA. O. Omoseebi

A. O. Omoseebi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


A. O. Omoseebi has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Paraffin Wax Deposition and Remediation Techniques in Crude Oil System: A Review

    by Nwitte Eze Ugo, A.O. Omoseebi, A.I. Alao, Babatunde Kazeem Adeoye

    Paraffin wax deposition is the major flow assurance issue in the oil industry. When the fluid temperature drops below the wax appearance temperature (WAT) due to the temperature differential between the cold areas and the crude oil, paraffin wax forms on the pipeline walls. Wax deposition can have very detrimental effects because it can narrow the internal diameters of pipelines and flowlines, which, if left unchecked, eventually clog these areas and force an activity to stop. However, overcoming the problems at this stage may become very expensive. This study examines the factors influencing paraffin wax deposition and discusses various methods for mitigating wax deposition on inner pipelines walls. It focuses on mechanical, thermal, chemical, bioremediation, and hybrid techniques. The benefits and limitations of each wax mitigation technique are assessed, along with the latest developments in modelling-based paraffin wax deposition mitigation. Although chemical techniques are preferable for treating deep-water wells due to their relatively inexpensiveness, simplicity, and no disruption to production, synthetic chemical inhibitors pose environmental hazardous. However, the advantages of organic chemical additives and bioremediation technique over commercially available synthetic chemical inhibitors are rigorously assessed in this work with regard to environmental benefits, sustainability advantages and improved process safety. This review also identifies the gaps in mitigation of paraffin wax deposition.

  • Evaluation of Abrasive Properties of Selected Granite Rocks and Their Effects on Button Bit Wear

    by Babatunde Adebayo, Thomas B. Afeni, Damilola J. Afu, Olaoluwa B. Ogunyemi, A. O. Omoseebi, Alexander Orunduyi

    Abrasive properties of selected rocks and their influence on button bit wear were investigated. Rock samples were obtained from three locations in Southwest, Nigeria. These samples were tested in the laboratory for grain size and circularity factor. Also, porosity, Equivalent Quartz content (EQC), Rock Hardness Number (RHN), Rock Abrasivity Index (RAI) and Uniaxial Compressive Strength were determined. Bit button lengths consumed were measured at regular interval as drilling operation progresses. Results of grain size revealed that medium feldspar granite has least average grain size varying from 0.12 – 0.14 mm. There is possibility that rate of drilling may be low while drilling through this rock. The values of circularity factor varied from 0.624 for medium feldspar granite to 0.786 for coarse muscovite granite . The mean values of porosity varied from between 0.85 and 1.33% for medium feldspar granite and coarse muscovite granite respectively. Biotite hornblende granite has the highest mean uniaxial compressive strength value of 119.48 MPa while coarse muscovite granite has the least mean value of 90.65 MPa. The values of free silica, EQC, RHN, and RAI varied from 35.93 – 51.35%, 45.60 – 67.21%, 575.52 – 821.64 kg/mm 3 and 4133.64 – 7003.71 respectively. It was observed that grain size affects the void size in these rocks, which accounted for least porosity value obtained in medium feldspar granite . Average bit button length consumed varied from 15.56 – 24.54 mm for gauge button while length of centre button varied from 13.00 – 19.61 mm. Higher gauge button length consumption could be inferred that it effects the cutting, crushing and wedging of rock mineral components at rock-bit interface. The understanding of grain size, circularity factor and abrasive properties will provide adequate information for quarry to select appropriate bit and drilling machine.