M.M. Dyachenko
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
M.M. Dyachenko has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Inna Shalevska
Physico-Technological Institute of Metals and Alloys of the National Academy of Sciences of Ukraine (Kyiv, Ukraine)
3 shared publications - I.V. Korniets2 shared publications
- P. B. Kaliuzhnyi
Physico-Technological Institute of Metals and Alloys of the National Academy of Science of Ukraine, Kyiv, Ukraine
2 shared publications - Svyatoslav Gnyloskurenko
Physico-Technological Institute of Metals and Alloys, National Academy of Sciences of Ukraine
2 shared publications І.в. Корнієць
Фізико-технологічний інститут металів та сплавів Національної академії наук України (Київ, Україна)
2 shared publications- M. I. Tarasevich
Фізико-технологічний інститут металів та сплавів Національної академії наук України (Київ, Україна)
1 shared publication
Latest Publications
- Open Access
- 29 May 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 34 (2) , 8-17
Determining the Influence of Sodium Silicate Content in the Filler of Cast Iron and Steel Cast Modules on Penetration Resistance Indicators
The article investigates the effect of sodium silicate content on the penetrability of liquid glass sand fillers integrated into cast iron and steel shells obtained by lost foam casting (LFC). Samples with a sodium silicate content of 4 to 16 g per 100 g of quartz sand were produced for testing using a laboratory drop hammer according to a method adapted for evaluating the knock-out properties of molding sands. It was found that the penetration work increases with increasing sodium silicate con- tent. For cast iron shells, a significant increase in resistance to penetration begins at a sodium silicate content of 9.1 %, while for steel shells – from 12.3 %. The transition layer between the metal and the filler in cast iron samples is 2–4 times thicker (1.5–4.0 mm) than in steel samples (0.5–1.6 mm), which is explained by the better fluidity of cast iron and higher adhesion of the silicate phase to cast iron. At the same time, the microstructure and microhardness of the transition layer do not depend on the sodium silicate content. For the "cast iron – liquid glass filler" system, a sodium silicate content of 12–14 g per 100 g of sand is recommended, and for the "steel – liquid glass filler" system – 14–16 g. The obtained results allow using the liquid glass filler as an effective substitute for part of the metal in cast modules of protective and load-bearing structures. У статті досліджено вплив вмісту рідкого скла на пробиваємість рідкоскляних піщаних наповнювачів, інтегрованих у чавунні та сталеві оболонки, отримані методом лиття за моделями, що газифікуються (ЛГМ). Були виготовлені зразки з вмістом рідкого скла від 4 до 16 г на 100 г кварцового піску для проведення випробування з використанням лабораторного копра за методикою, адаптованою для оцінки вибивності ливарних сумішей. Встановлено, що робота пробивання зростає зі збільшенням вмісту рідкого скла. Для чавунних оболонок істотне зростання стійкості до пробивання починається при вмісті рідкого скла 9,1 %, а для сталевих — від 12,3 %. Перехідний шар між металом і наповнювачем у чавунних зразках є в 2—4 рази товщим (1,5—4,0 мм), ніж у сталевих (0,5—1,6 мм), що пояснюється кращою рідкоплинністю чавуну та вищою адгезією силікатної фази до чавуну. Водночас мікроструктура та мікротвердість перехідного шару не залежать від вмісту рідкого скла. Рекомендовано застосовувати для системи «чавун — рідкоскляний наповнювач» вміст рідкого скла 12—14 г на 100 г піску, а для системи «сталь — рідкоскляний наповнювач» — 14–16 г. Отримані результати дозволяють використовувати рідкоскляний наповнювач як ефективну заміну частини металу в литих модулях захисних та несучих конструкцій.
- 29 May 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 34 (2) , 8-17
Open AccessDetermining the Influence of Sodium Silicate Content in the Filler of Cast Iron and Steel Cast Modules on Penetration Resistance Indicators
The article investigates the effect of sodium silicate content on the penetrability of liquid glass sand fillers integrated into cast iron and steel shells obtained by lost foam casting (LFC). Samples with a sodium silicate content of 4 to 16 g per 100 g of quartz sand were produced for testing using a laboratory drop hammer according to a method adapted for evaluating the knock-out properties of molding sands. It was found that the penetration work increases with increasing sodium silicate con- tent. For cast iron shells, a significant increase in resistance to penetration begins at a sodium silicate content of 9.1 %, while for steel shells – from 12.3 %. The transition layer between the metal and the filler in cast iron samples is 2–4 times thicker (1.5–4.0 mm) than in steel samples (0.5–1.6 mm), which is explained by the better fluidity of cast iron and higher adhesion of the silicate phase to cast iron. At the same time, the microstructure and microhardness of the transition layer do not depend on the sodium silicate content. For the "cast iron – liquid glass filler" system, a sodium silicate content of 12–14 g per 100 g of sand is recommended, and for the "steel – liquid glass filler" system – 14–16 g. The obtained results allow using the liquid glass filler as an effective substitute for part of the metal in cast modules of protective and load-bearing structures. У статті досліджено вплив вмісту рідкого скла на пробиваємість рідкоскляних піщаних наповнювачів, інтегрованих у чавунні та сталеві оболонки, отримані методом лиття за моделями, що газифікуються (ЛГМ). Були виготовлені зразки з вмістом рідкого скла від 4 до 16 г на 100 г кварцового піску для проведення випробування з використанням лабораторного копра за методикою, адаптованою для оцінки вибивності ливарних сумішей. Встановлено, що робота пробивання зростає зі збільшенням вмісту рідкого скла. Для чавунних оболонок істотне зростання стійкості до пробивання починається при вмісті рідкого скла 9,1 %, а для сталевих — від 12,3 %. Перехідний шар між металом і наповнювачем у чавунних зразках є в 2—4 рази товщим (1,5—4,0 мм), ніж у сталевих (0,5—1,6 мм), що пояснюється кращою рідкоплинністю чавуну та вищою адгезією силікатної фази до чавуну. Водночас мікроструктура та мікротвердість перехідного шару не залежать від вмісту рідкого скла. Рекомендовано застосовувати для системи «чавун — рідкоскляний наповнювач» вміст рідкого скла 12—14 г на 100 г піску, а для системи «сталь — рідкоскляний наповнювач» — 14–16 г. Отримані результати дозволяють використовувати рідкоскляний наповнювач як ефективну заміну частини металу в литих модулях захисних та несучих конструкцій.
- 29 May 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 164 (2) , 31-38
ЗМЕНШЕННЯ ВИКИДІВ ШКІДЛИВИХ РЕЧОВИН ПРИ ВИГОТОВЛЕННІ ЛИТИХ КОНСТРУКЦІЙ ІЗ НЕМЕТАЛЕВИМ НАПОВНЮВАЧЕМ
- 29 May 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 164 (2) , 31-38
ЗМЕНШЕННЯ ВИКИДІВ ШКІДЛИВИХ РЕЧОВИН ПРИ ВИГОТОВЛЕННІ ЛИТИХ КОНСТРУКЦІЙ ІЗ НЕМЕТАЛЕВИМ НАПОВНЮВАЧЕМ
- Open Access
- 1 January 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 33 (3-4) , 119
Investigation of the Processes of Transition Layer Formation at the Interface of Gray Cast Iron–Integrated Non-Metallic Filler in the Production of Lightweight Castings
One of the promising approaches for creating reliable and lightweight structures with specified operational properties is the use of lightweight composite castings with integrated ceramic fillers. The key factor determining the quality of such castings is the bond strength of the transition layer at the metal–ceramic interface. The aim of this work was to study the physicochemical processes of transition layer formation between a melt of gray cast iron SCh200 and two types of integrated ceramic fillers (a liquid glass mixture and expanded clay) during the production of castings using the lost foam casting (LFC) method. The work involved an analysis of thermal regimes and possible chemical reactions. The thermodynamic probability of the formation of silicates (ferrosilite, rhodonite) and capillary phenomena were theoretically analyzed. For modeling, a mathematical heat transfer model implemented in a specialized software package developed at the PTIMA of the National Academy of Sciences of Ukraine was used. Hollow castings (module segments) with integrated fillers were experimentally produced using LFC technology. The structure was investigated using optical microscopy methods. The modeling results revealed differences in the thermal regimes and the dynamics of casting formation for the two filler types. For the system with the liquid glass mixture, a significant temperature gradient formed, indicating active heat absorption and promoting the mechanism of deep capillary impregnation. The experiment confirmed the formation of a pronounced mechanical bonding zone with a depth of 0.5–1.5 mm, with signs of additional chemical interaction. In contrast, for the system with expanded clay, a rapid and uniform heating of the filler due to convection was observed, which determined the mechanism of surface physicochemical interaction and the formation of a thin (0.1–0.3 mm) dense layer. Based on the obtained data, it was established that the pouring temperature of 1430 °C ensures the formation of the transition layer for both filler types. The article compares the mechanisms of transition layer formation for two thermophysically different fillers under the conditions of LFC technology. A relationship is shown between the predicted thermal fields and the thickness of the formed transition layer. The obtained results are useful for the production technologies of lightweight cast parts with local reinforcement. Одним із перспективних шляхів створення надійних та легких конструкцій із заданими експлуатаційними властивостями є використання литих легковагових композиційних виливків з інтегрованими керамічними наповнювачами. Ключовим фактором, що визначає якість таких виливків, є міцність зв’язку перехідного шару на межі розділу метал–кераміка. Метою роботи було дослідження фізико-хімічних процесів формування перехідного шару між розплавом сірого чавуну СЧ200 та двома типами інтегрованих керамічних наповнювачів (рідкоскляною сумішшю та керамзитом) при виготовленні виливків методом лиття за моделями, що газифікуються (ЛГМ). У роботі проведено аналіз теплових режимів і можливих хімічних реакцій. Теоретично проаналізовано термодинамічну ймовірність утворення силікатів (феросилікату, родоніту) та капілярні явища. Для моделювання використана математична модель теплопереносу, реалізована в спеціалізованому програмному комплексі, розробленому у ФТІМС НАН України. Експериментально виготовлено порожнисті виливки (сегменти модулів) з інтегрованими наповнювачами за технологією ЛГМ. Структуру досліджували методами оптичної мікроскопії. Результати моделювання виявили відмінності в теплових режимах та динаміці формування виливків для двох типів наповнювачів. Для системи з рідкоскляною сумішшю (РСС) формувався значний градієнт температури, що свідчить про активне поглинання тепла та сприяло механізму глибокого капілярного просочення. Експеримент підтвердив формування вираженої зони механічного зчеплення глибиною 0,5—1,5 мм, що супроводжувалося хімічною взаємодією. На противагу, для системи з керамзитом спостерігався швидкий і рівномірний прогрів наповнювача за рахунок конвекції, що обумовило механізм поверхневої фізико-хімічної взаємодії та утворення тонкого (0,1—0,3 мм) щільного шару. На основі отриманих даних встановлено, що температура заливання 1430 °C забезпечує формування перехідного шару для обох...
- 1 January 2026
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 33 (3-4) , 119
Open AccessInvestigation of the Processes of Transition Layer Formation at the Interface of Gray Cast Iron–Integrated Non-Metallic Filler in the Production of Lightweight Castings
One of the promising approaches for creating reliable and lightweight structures with specified operational properties is the use of lightweight composite castings with integrated ceramic fillers. The key factor determining the quality of such castings is the bond strength of the transition layer at the metal–ceramic interface. The aim of this work was to study the physicochemical processes of transition layer formation between a melt of gray cast iron SCh200 and two types of integrated ceramic fillers (a liquid glass mixture and expanded clay) during the production of castings using the lost foam casting (LFC) method. The work involved an analysis of thermal regimes and possible chemical reactions. The thermodynamic probability of the formation of silicates (ferrosilite, rhodonite) and capillary phenomena were theoretically analyzed. For modeling, a mathematical heat transfer model implemented in a specialized software package developed at the PTIMA of the National Academy of Sciences of Ukraine was used. Hollow castings (module segments) with integrated fillers were experimentally produced using LFC technology. The structure was investigated using optical microscopy methods. The modeling results revealed differences in the thermal regimes and the dynamics of casting formation for the two filler types. For the system with the liquid glass mixture, a significant temperature gradient formed, indicating active heat absorption and promoting the mechanism of deep capillary impregnation. The experiment confirmed the formation of a pronounced mechanical bonding zone with a depth of 0.5–1.5 mm, with signs of additional chemical interaction. In contrast, for the system with expanded clay, a rapid and uniform heating of the filler due to convection was observed, which determined the mechanism of surface physicochemical interaction and the formation of a thin (0.1–0.3 mm) dense layer. Based on the obtained data, it was established that the pouring temperature of 1430 °C ensures the formation of the transition layer for both filler types. The article compares the mechanisms of transition layer formation for two thermophysically different fillers under the conditions of LFC technology. A relationship is shown between the predicted thermal fields and the thickness of the formed transition layer. The obtained results are useful for the production technologies of lightweight cast parts with local reinforcement. Одним із перспективних шляхів створення надійних та легких конструкцій із заданими експлуатаційними властивостями є використання литих легковагових композиційних виливків з інтегрованими керамічними наповнювачами. Ключовим фактором, що визначає якість таких виливків, є міцність зв’язку перехідного шару на межі розділу метал–кераміка. Метою роботи було дослідження фізико-хімічних процесів формування перехідного шару між розплавом сірого чавуну СЧ200 та двома типами інтегрованих керамічних наповнювачів (рідкоскляною сумішшю та керамзитом) при виготовленні виливків методом лиття за моделями, що газифікуються (ЛГМ). У роботі проведено аналіз теплових режимів і можливих хімічних реакцій. Теоретично проаналізовано термодинамічну ймовірність утворення силікатів (феросилікату, родоніту) та капілярні явища. Для моделювання використана математична модель теплопереносу, реалізована в спеціалізованому програмному комплексі, розробленому у ФТІМС НАН України. Експериментально виготовлено порожнисті виливки (сегменти модулів) з інтегрованими наповнювачами за технологією ЛГМ. Структуру досліджували методами оптичної мікроскопії. Результати моделювання виявили відмінності в теплових режимах та динаміці формування виливків для двох типів наповнювачів. Для системи з рідкоскляною сумішшю (РСС) формувався значний градієнт температури, що свідчить про активне поглинання тепла та сприяло механізму глибокого капілярного просочення. Експеримент підтвердив формування вираженої зони механічного зчеплення глибиною 0,5—1,5 мм, що супроводжувалося хімічною взаємодією. На противагу, для системи з керамзитом спостерігався швидкий і рівномірний прогрів наповнювача за рахунок конвекції, що обумовило механізм поверхневої фізико-хімічної взаємодії та утворення тонкого (0,1—0,3 мм) щільного шару. На основі отриманих даних встановлено, що температура заливання 1430 °C забезпечує формування перехідного шару для обох...
- 1 September 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 33 (2) , 30-37
Influence of Diameter and Volume Fraction of Reinforcing Elements on the Formation of Composite Castings
For modern machinery, composite materials are of great importance because they ensure improved properties of parts. The work is dedicated to study the influence of the diameter and volume fraction of the reinforcement elements in the form of rods on the thermal processes that occur during the crystallization and structure formation of cast steel composites. Computational experiment and computer modeling were used to study the thermal interaction between the matrix melt (steel 35) and reinforcing elements (steel 20), phase transformation at their different diameters (2-10 mm) and volume fraction (10-50 %), the formation and growth dynamics of solid crusts at the interface between the “melt – reinforcing element” phases and the critical parameters that ensure optimal connection of the matrix alloy with the reinforcing elements. As a result a critical relationship of the diameter and volume fraction of the reinforcing elements (18–31.5 %) was established, which influences the quality of adhesion (bonding) between phases and the microstructure of the material. Regression models have been developed to predict temperature regimes on the surface of reinforcing elements depending on their diameter and volume fraction and the optimal technological parameters for obtaining composite castings have been determined. With diameters of reinforcing elements of 2-5 mm, their volume fraction of 10-50 % complete melting of the reinforcing phase occurs, which ensures homogenization of the structure. For rod diameters of 6-10 mm their critical (or maximum) volume fractions are indicated for 7 mm — 21 %, for 9 mm — 16 %, in which optimal phase connection is achieved without creating a stable solid crust. The practical significance of these results lies in the possibility of precise control and optimization of technological parameters when obtaining high-quality cast composites with minimal defects. Для сучасного машинобудування актуальними є композиційні матеріали, які забезпечують покращені властивості деталей. Роботу присвячено дослідженню впливу діаметра та об'ємної частки армувальних елементів у вигляді стрижнів на теплові процеси, які мають місце при кристалізації та формуванні структури литих сталевих композиційних матеріалів. Методами обчислювального експерименту та комп'ютерного моделювання було досліджено теплову взаємодію між матричним розплавом (сталь 35) та армуючими елементами (сталь 20), фазові перетворення при різних поєднаннях їх діаметрів (2—10 мм) та об'ємної частки (10—50 %), утворення та динаміку росту твердих кірок на межі розділу фаз «рідкий сплав — армувальний елемент», критичні параметри, що забезпечують оптимальне з’єднання матричного сплаву з армуючими елементами. У результаті роботи встановлені критичні співвідношення діаметра та об'ємної частки армуючих елементів (18—31,5 %), які впливають на якість зчеплення фаз та мікроструктуру матеріалу, розроблені регресійні моделі для прогнозування температурних режимів на поверхні армуючих елементів залежно від їх діаметра та об'ємної частки, визначені оптимальні технологічні параметри одержання композиційних виливків. При діаметрах армуючих елементів 2—5 мм та об'ємній їх частці 10—50 % відбувається повне розплавлення армуючої фази, що забезпечує гомогенізацію структури. Для стрижнів діаметром 6—10 мм визначено граничні об'ємні частки: для 7 мм — 21 %, для 9 мм — 16 %, при яких досягається оптимальне з'єднання фаз без утворення стійкої твердої кірки. Практична значимість одержаних результатів полягає у можливості точного контролю та оптимізації технологічних параметрів при одержанні якісних литих композитів з мінімальними дефектами.
- 1 September 2025
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Metal and Casting of Ukraine
- Vol. 33 (2) , 30-37
Influence of Diameter and Volume Fraction of Reinforcing Elements on the Formation of Composite Castings
For modern machinery, composite materials are of great importance because they ensure improved properties of parts. The work is dedicated to study the influence of the diameter and volume fraction of the reinforcement elements in the form of rods on the thermal processes that occur during the crystallization and structure formation of cast steel composites. Computational experiment and computer modeling were used to study the thermal interaction between the matrix melt (steel 35) and reinforcing elements (steel 20), phase transformation at their different diameters (2-10 mm) and volume fraction (10-50 %), the formation and growth dynamics of solid crusts at the interface between the “melt – reinforcing element” phases and the critical parameters that ensure optimal connection of the matrix alloy with the reinforcing elements. As a result a critical relationship of the diameter and volume fraction of the reinforcing elements (18–31.5 %) was established, which influences the quality of adhesion (bonding) between phases and the microstructure of the material. Regression models have been developed to predict temperature regimes on the surface of reinforcing elements depending on their diameter and volume fraction and the optimal technological parameters for obtaining composite castings have been determined. With diameters of reinforcing elements of 2-5 mm, their volume fraction of 10-50 % complete melting of the reinforcing phase occurs, which ensures homogenization of the structure. For rod diameters of 6-10 mm their critical (or maximum) volume fractions are indicated for 7 mm — 21 %, for 9 mm — 16 %, in which optimal phase connection is achieved without creating a stable solid crust. The practical significance of these results lies in the possibility of precise control and optimization of technological parameters when obtaining high-quality cast composites with minimal defects. Для сучасного машинобудування актуальними є композиційні матеріали, які забезпечують покращені властивості деталей. Роботу присвячено дослідженню впливу діаметра та об'ємної частки армувальних елементів у вигляді стрижнів на теплові процеси, які мають місце при кристалізації та формуванні структури литих сталевих композиційних матеріалів. Методами обчислювального експерименту та комп'ютерного моделювання було досліджено теплову взаємодію між матричним розплавом (сталь 35) та армуючими елементами (сталь 20), фазові перетворення при різних поєднаннях їх діаметрів (2—10 мм) та об'ємної частки (10—50 %), утворення та динаміку росту твердих кірок на межі розділу фаз «рідкий сплав — армувальний елемент», критичні параметри, що забезпечують оптимальне з’єднання матричного сплаву з армуючими елементами. У результаті роботи встановлені критичні співвідношення діаметра та об'ємної частки армуючих елементів (18—31,5 %), які впливають на якість зчеплення фаз та мікроструктуру матеріалу, розроблені регресійні моделі для прогнозування температурних режимів на поверхні армуючих елементів залежно від їх діаметра та об'ємної частки, визначені оптимальні технологічні параметри одержання композиційних виливків. При діаметрах армуючих елементів 2—5 мм та об'ємній їх частці 10—50 % відбувається повне розплавлення армуючої фази, що забезпечує гомогенізацію структури. Для стрижнів діаметром 6—10 мм визначено граничні об'ємні частки: для 7 мм — 21 %, для 9 мм — 16 %, при яких досягається оптимальне з'єднання фаз без утворення стійкої твердої кірки. Практична значимість одержаних результатів полягає у можливості точного контролю та оптимізації технологічних параметрів при одержанні якісних литих композитів з мінімальними дефектами.
- Open Access
- 5 June 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 156 (2) , 19-28
CASTING ACCORDING TO GAS-PERMEABLE POLYMER MODELS THAT ARE GASIFIED WITH PUMPING OF GASES FROM THE WORKING CAVITY OF THE MOLD THROUGH VENT CHANNELS
The technical information notes the predominant development of special methods of casting, in particular, casting under pressure, as well as with vacuum casting. Also today, digitization and automation are perceived as a necessary condition for the organization of production processes. In particular, this concerns the foundry industry of Ukraine to create a powerful potential that will contribute to the recovery of the country. A review of the work developed by the department of Prof. O. Y. Shinsky series of methods of casting metal according to patterns that are gasified (Lost Foam casting, LFC) in sand molds using regulated gas pressure or rarefaction. The described methods combine the use of single-use patterns with ventilation channels to create a directed gas regime in the pattern and form and the adjustable effect of gas pressure on filling the form with metal. These methods allow both to regulate the filling of the mold with metal, affecting the quality of the castings, and to manufacture metal products of complex configuration with printing of their patterns in automatic mode based on digital data, which corresponds to the growing trend of digitization and automation of foundry processes. The total benefit is obtained from both the fairly fast 3D printing of the foundry pattern and the short-term processes of forming and punching out the castings thanks to the use of dry sand casting molds. At the same time, the digital transformation of LFC is combined with the efficiency of reversible application of molding materials without changing the current standards of control of metal products, which is often characteristic of methods of 3D printing of metal structures. Adaptation of production to additive technologies allows interaction with the buyer of the product, which is designed according to his individual digital drawing, using the Internet. Also, this combination of new digital processes with traditional production processes shortens the time gap from the creation of prototypes, pilot samples of products to mass production. У технічній літературі відзначається переважний розвиток спеціальних способів лиття, зокрема лиття під тиском та з вакуумуванням ливарної форми. Цифровізація та автоматизація також сприймаються сьогодні як обов’язкова умова організації виробничих процесів. Це в першу чергу стосується ливарного виробництва України для створення потужного потенціалу, що сприятиме відновленню країни. Проведено огляд розроблених під керівництвом проф. О.Й. Шинського низки способів лиття металу за моделями, що газифікуються (ЛГМ) в піщаних формах із використанням регульованого газового тиску чи розрідження. Описані способи об’єднує застосування разових моделей із вентиляційними каналами для створення направленого газового режиму в моделі та формі й регульованого впливу газового тиску на заливання форми металом. Ці способи дозволяють як регулювати заповнення форми металом, впливаючи на якість виливків, так і виготовляти металовироби складної конфігурації з друкуванням їх моделей в автоматичному режимі за цифровими даними, що відповідає зростаючому тренду цифровізації та автоматизації ливарних процесів. Сумарну вигоду буде отримано як від доволі швидкісного 3D-друку ливарної моделі, так і від короткотривалих процесів формування та вибивання виливків завдяки використанню ливарних форм із сухого піску. При цьому цифрова трансформація ЛГМ поєднується з ефективністю оборотного застосування формувальних матеріалів без зміни чинних стандартів контролю металопродукції, що нерідко властиво способам 3D-друку металоконструкцій. Адаптація виробництва до адитивних технологій дозволяє за допомогою інтернет-мережі взаємодіяти з покупцем товару, який проєктується за його індивідуальним цифровим кресленням. Крім того, поєднання нових цифрових процесів із традиційними виробничими скорочує часовий розрив від створення прототипів, пілотних зразків продукції до масового виробництва.
- 5 June 2024
- Published by National Academy of Sciences of Ukraine (Co. LTD Ukrinformnauka) (Publications) in Casting Processes
- Vol. 156 (2) , 19-28
Open AccessCASTING ACCORDING TO GAS-PERMEABLE POLYMER MODELS THAT ARE GASIFIED WITH PUMPING OF GASES FROM THE WORKING CAVITY OF THE MOLD THROUGH VENT CHANNELS
The technical information notes the predominant development of special methods of casting, in particular, casting under pressure, as well as with vacuum casting. Also today, digitization and automation are perceived as a necessary condition for the organization of production processes. In particular, this concerns the foundry industry of Ukraine to create a powerful potential that will contribute to the recovery of the country. A review of the work developed by the department of Prof. O. Y. Shinsky series of methods of casting metal according to patterns that are gasified (Lost Foam casting, LFC) in sand molds using regulated gas pressure or rarefaction. The described methods combine the use of single-use patterns with ventilation channels to create a directed gas regime in the pattern and form and the adjustable effect of gas pressure on filling the form with metal. These methods allow both to regulate the filling of the mold with metal, affecting the quality of the castings, and to manufacture metal products of complex configuration with printing of their patterns in automatic mode based on digital data, which corresponds to the growing trend of digitization and automation of foundry processes. The total benefit is obtained from both the fairly fast 3D printing of the foundry pattern and the short-term processes of forming and punching out the castings thanks to the use of dry sand casting molds. At the same time, the digital transformation of LFC is combined with the efficiency of reversible application of molding materials without changing the current standards of control of metal products, which is often characteristic of methods of 3D printing of metal structures. Adaptation of production to additive technologies allows interaction with the buyer of the product, which is designed according to his individual digital drawing, using the Internet. Also, this combination of new digital processes with traditional production processes shortens the time gap from the creation of prototypes, pilot samples of products to mass production. У технічній літературі відзначається переважний розвиток спеціальних способів лиття, зокрема лиття під тиском та з вакуумуванням ливарної форми. Цифровізація та автоматизація також сприймаються сьогодні як обов’язкова умова організації виробничих процесів. Це в першу чергу стосується ливарного виробництва України для створення потужного потенціалу, що сприятиме відновленню країни. Проведено огляд розроблених під керівництвом проф. О.Й. Шинського низки способів лиття металу за моделями, що газифікуються (ЛГМ) в піщаних формах із використанням регульованого газового тиску чи розрідження. Описані способи об’єднує застосування разових моделей із вентиляційними каналами для створення направленого газового режиму в моделі та формі й регульованого впливу газового тиску на заливання форми металом. Ці способи дозволяють як регулювати заповнення форми металом, впливаючи на якість виливків, так і виготовляти металовироби складної конфігурації з друкуванням їх моделей в автоматичному режимі за цифровими даними, що відповідає зростаючому тренду цифровізації та автоматизації ливарних процесів. Сумарну вигоду буде отримано як від доволі швидкісного 3D-друку ливарної моделі, так і від короткотривалих процесів формування та вибивання виливків завдяки використанню ливарних форм із сухого піску. При цьому цифрова трансформація ЛГМ поєднується з ефективністю оборотного застосування формувальних матеріалів без зміни чинних стандартів контролю металопродукції, що нерідко властиво способам 3D-друку металоконструкцій. Адаптація виробництва до адитивних технологій дозволяє за допомогою інтернет-мережі взаємодіяти з покупцем товару, який проєктується за його індивідуальним цифровим кресленням. Крім того, поєднання нових цифрових процесів із традиційними виробничими скорочує часовий розрив від створення прототипів, пілотних зразків продукції до масового виробництва.