Owen Moynihan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Owen Moynihan has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
Kevin Thomas
Tyndall National Institute, University College Cork, Cork, Ireland
4 shared publicationsBrendan Roycroft
Tyndall National Institute, University College Cork, Cork, Ireland
2 shared publicationsBrian Corbett
Tyndall National Institute, University College Cork, Cork, Ireland
2 shared publications- Brian Corbett
Tyndall National Institute, Lee Maltings, Cork, Ireland
2 shared publications Emanuele Pelucchi
Tyndall National Institute, University College Cork, Cork, Ireland
2 shared publications- Emanuele Pelucchi
Tyndall National Institute, Lee Maltings, Cork, Ireland
2 shared publications
Latest Publications
- 1 January 2025
- Published by Optica Publishing Group
- p. SS136_2
Broadband Light Emission from InP Based Nanostructures using MOVPE
A novel nanostructured material embedded in a p-n diode structure is introduced. Excellent diode characteristics and a broadband emission spectrum with full width at half maximum of 220 nm centered around 1480 nm are measured.
- 1 January 2025
- Published by Optica Publishing Group
- p. SS136_2
Broadband Light Emission from InP Based Nanostructures using MOVPE
A novel nanostructured material embedded in a p-n diode structure is introduced. Excellent diode characteristics and a broadband emission spectrum with full width at half maximum of 220 nm centered around 1480 nm are measured.
- Open Access
- 19 August 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (8)
Scalable transfer printing approach to heterogeneous integration of InP lasers on silicon-on-insulator waveguide platform
InP-based edge-emitting O-band lasers are integrated onto silicon photonics circuit employing micro-transfer printing technology. Blocks of unpatterned InP gain material of typical size 1000 × 60 μ m2 are first transferred onto 400 nm thick silicon rib waveguides with the fabrication steps performed on the target wafer to realize the final lasers. As a result, the InP ridge waveguides are aligned with lithographic accuracy to the underlying Si waveguides resulting in an approach free from any misalignment stemming from the transfer printing process. The fabricated Distributed Bragg Reflector laser shows lasing around 100 mA current injection with minimum 1 mW of output power coupled to a single mode fiber. This integration method paves a reliable route toward scaling-up the integration of active devices such as lasers, modulators, and detectors on 300-mm diameter silicon wafers, which requires high-uniformity across the wafer.
- 19 August 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (8)
Open AccessScalable transfer printing approach to heterogeneous integration of InP lasers on silicon-on-insulator waveguide platform
InP-based edge-emitting O-band lasers are integrated onto silicon photonics circuit employing micro-transfer printing technology. Blocks of unpatterned InP gain material of typical size 1000 × 60 μ m2 are first transferred onto 400 nm thick silicon rib waveguides with the fabrication steps performed on the target wafer to realize the final lasers. As a result, the InP ridge waveguides are aligned with lithographic accuracy to the underlying Si waveguides resulting in an approach free from any misalignment stemming from the transfer printing process. The fabricated Distributed Bragg Reflector laser shows lasing around 100 mA current injection with minimum 1 mW of output power coupled to a single mode fiber. This integration method paves a reliable route toward scaling-up the integration of active devices such as lasers, modulators, and detectors on 300-mm diameter silicon wafers, which requires high-uniformity across the wafer.
- Open Access
- 29 July 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (5)
Micro-transfer printed high-speed InP-based electro-absorption modulator on silicon-on-insulator
A high-speed InP-based electro-absorption modulator (EAM) on 220 nm silicon-on-insulator (SOI) is designed, fabricated, and measured. The III–V device is heterogeneously integrated to the SOI using transfer printing, with direct bonding. The printing accuracy of the device was within ±0.5 μm. This design evanescently couples light between the III–V waveguide and the SOI via a taper region in the InP ridge for high transmission. This method is a flexible and robust method of transferring an InP EAM to SOI, where multiple device variations have been transferred. At 1550 nm, the printed EAM has a measured electrical bandwidth of up to 40 GHz, an extinction ratio (ER) of 30 dB from 0 to −6 V, and an insertion loss of 6.5 dB, which reduces with longer wavelengths. An ER of 25 dB is obtained over a spectral bandwidth of 30 nm with biasing to −8 V. Open-eye diagrams were measured up to 50 Gbps in a back-to-back measurement. This device is suitable for applications in high-speed communications and sensing, leveraging the added advantage of III–V absorption modulation on a silicon photonics platform.
- 29 July 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (5)
Open AccessMicro-transfer printed high-speed InP-based electro-absorption modulator on silicon-on-insulator
A high-speed InP-based electro-absorption modulator (EAM) on 220 nm silicon-on-insulator (SOI) is designed, fabricated, and measured. The III–V device is heterogeneously integrated to the SOI using transfer printing, with direct bonding. The printing accuracy of the device was within ±0.5 μm. This design evanescently couples light between the III–V waveguide and the SOI via a taper region in the InP ridge for high transmission. This method is a flexible and robust method of transferring an InP EAM to SOI, where multiple device variations have been transferred. At 1550 nm, the printed EAM has a measured electrical bandwidth of up to 40 GHz, an extinction ratio (ER) of 30 dB from 0 to −6 V, and an insertion loss of 6.5 dB, which reduces with longer wavelengths. An ER of 25 dB is obtained over a spectral bandwidth of 30 nm with biasing to −8 V. Open-eye diagrams were measured up to 50 Gbps in a back-to-back measurement. This device is suitable for applications in high-speed communications and sensing, leveraging the added advantage of III–V absorption modulation on a silicon photonics platform.
- 16 June 2024
- Published by Springer Nature
- p. 53-57
III-V Electro-Absorption Modulation and Detection Devices Integrated to 220 nm Silicon-on-Insulator
- 16 June 2024
- Published by Springer Nature
- p. 53-57
III-V Electro-Absorption Modulation and Detection Devices Integrated to 220 nm Silicon-on-Insulator
- Open Access
- 19 March 2024
- Published by University College Cork in The Boolean: Snapshots of Doctoral Research at University College Cork
- p. 19-25
Mixing Materials for Integrated Photonic Innovation
Photonics, an ever-growing field since the invention of lasers in the 1960s, has been applied in wide-ranging applications such as optical communications, sensing, imaging and more. Photonic integrated circuits (PIC) are the next step to take this technology and shrink it onto a semiconductor chip, leading to more compact, cheaper, and lower power consumption solutions. However, integrated photonics faces the challenge of lacking a single material platform that encompasses all the desired properties, unlike its more mature electronic integrated circuit counterpart which uses silicon with a standardised fabrication process known as complementary metal oxide semiconductor (CMOS). To overcome this limitation, researchers are exploring hybrid and heterogeneous integration techniques. By combining the strengths of different photonic platforms, such as III-V materials for light emission, silicon for strong light guidance, silicon-nitride for visible light guiding, and lithium niobate for its modulating capabilities, integrated photonic technologies can harness the collective advantages and unlock new possibilities. “Light brings us the news from the universe.” — Sir William Bragg
- 19 March 2024
- Published by University College Cork in The Boolean: Snapshots of Doctoral Research at University College Cork
- p. 19-25
Open AccessMixing Materials for Integrated Photonic Innovation
Photonics, an ever-growing field since the invention of lasers in the 1960s, has been applied in wide-ranging applications such as optical communications, sensing, imaging and more. Photonic integrated circuits (PIC) are the next step to take this technology and shrink it onto a semiconductor chip, leading to more compact, cheaper, and lower power consumption solutions. However, integrated photonics faces the challenge of lacking a single material platform that encompasses all the desired properties, unlike its more mature electronic integrated circuit counterpart which uses silicon with a standardised fabrication process known as complementary metal oxide semiconductor (CMOS). To overcome this limitation, researchers are exploring hybrid and heterogeneous integration techniques. By combining the strengths of different photonic platforms, such as III-V materials for light emission, silicon for strong light guidance, silicon-nitride for visible light guiding, and lithium niobate for its modulating capabilities, integrated photonic technologies can harness the collective advantages and unlock new possibilities. “Light brings us the news from the universe.” — Sir William Bragg