Tsubasa Shiono
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tsubasa Shiono has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Hidekazu Tsuchida
Central Research Institute of Electric Power Industry (CRIEPI)
2 shared publications - Koichi Murata
Central Research Institute of Electric Power Industry (CRIEPI)
2 shared publications - Naoto Ishibashi
Resonac Corporation 2 , 1-9-1 Higashi Shimbashi, Minato, Tokyo 105-7325
2 shared publications - Yuichiro Mabuchi
Resonac Corporation 2 , 1-9-1 Higashi Shimbashi, Minato, Tokyo 105-7325
2 shared publications - Fumihiro Fujie
Central Research Institute of Electric Power Industry (CRIEPI) 1 , 2-6-1 Nagasaka, Yokosuka, Kanagawa 240-0196, Japan
1 shared publication - Satoshi Asada
Central Research Institute of Electric Power Industry (CRIEPI) , 2-6-1 Nagasaka, Yokosuka, Kanagawa 240-0196
1 shared publication
Latest Publications
- 1 September 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (9)
Characterization and modeling of forward current conduction in 4H-SiC PiN diodes based on device simulation analysis
The decay curves in time-resolved photoluminescence (TRPL) characteristics of n-type 4H-SiC epilayers were simulated by a technology computer aided design (TCAD) and compared with experimental results. In the simulation of TRPL decay curves, the direct recombination rate in the epilayer after illuminating samples with a pulse laser was regarded as the PL intensity. The simulated time-dependent PL intensities were fitted to the experimental results by adjusting the parameter AP, which characterizes Shockley–Read–Hall carrier recombination ratio. By employing the value of AP determined from the analysis on TRPL decay curves, a successful reproduction of experimental current–voltage characteristics of SiC PiN diodes fabricated on the epilayers was achieved by TCAD simulation at various temperatures ranging from 300 to 523 K.
- 1 September 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 140 (9)
Characterization and modeling of forward current conduction in 4H-SiC PiN diodes based on device simulation analysis
The decay curves in time-resolved photoluminescence (TRPL) characteristics of n-type 4H-SiC epilayers were simulated by a technology computer aided design (TCAD) and compared with experimental results. In the simulation of TRPL decay curves, the direct recombination rate in the epilayer after illuminating samples with a pulse laser was regarded as the PL intensity. The simulated time-dependent PL intensities were fitted to the experimental results by adjusting the parameter AP, which characterizes Shockley–Read–Hall carrier recombination ratio. By employing the value of AP determined from the analysis on TRPL decay curves, a successful reproduction of experimental current–voltage characteristics of SiC PiN diodes fabricated on the epilayers was achieved by TCAD simulation at various temperatures ranging from 300 to 523 K.
- Open Access
- 17 June 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (23)
Formation of basal plane dislocations by stress near epilayer/substrate interface of large-diameter SiC wafers with thick epitaxial layers
For large-diameter (150 mm) SiC epitaxial wafers with thick n− epilayers, stress analysis based on the finite element method and defect characterization near the epi/sub interface by synchrotron x-ray topography were performed. Observations on epitaxial wafers with epilayer thicknesses of 10, 20, 50, and 100 μm revealed that basal plane dislocation (BPD) half-loops were formed near triangular defects or from the edge of the wafer at an epilayer thickness of 50 μm and above. Two types of BPD half-loops with different edge components were observed: one with an extra half-plane above the core and present on the substrate side, and the other with a Burgers vector of opposite sign and present in the epilayer and at the epi/sub interface, forming an interfacial dislocation. The signs of these BPDs are consistent with those predicted from the calculation results, which mitigate compressive and tensile stresses in the epilayer and the substrate, respectively. It is considered that a thicker epilayer increases tensile stress in the substrate, which induces the formation of the BPD with an extra half-plane above the core on the substrate side. The distribution of the BPD half-loop width was also analyzed and compared with the calculated shear stress distribution caused by the radial temperature gradient. Calculations considering the local stress near the triangular defect revealed that the tensile stress near the epi/sub interface locally increases, exceeding the critical stress to form BPD, with an extra half-plane above the core for wafers with an epilayer thickness above 50 μm.
- 17 June 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 135 (23)
Open AccessFormation of basal plane dislocations by stress near epilayer/substrate interface of large-diameter SiC wafers with thick epitaxial layers
For large-diameter (150 mm) SiC epitaxial wafers with thick n− epilayers, stress analysis based on the finite element method and defect characterization near the epi/sub interface by synchrotron x-ray topography were performed. Observations on epitaxial wafers with epilayer thicknesses of 10, 20, 50, and 100 μm revealed that basal plane dislocation (BPD) half-loops were formed near triangular defects or from the edge of the wafer at an epilayer thickness of 50 μm and above. Two types of BPD half-loops with different edge components were observed: one with an extra half-plane above the core and present on the substrate side, and the other with a Burgers vector of opposite sign and present in the epilayer and at the epi/sub interface, forming an interfacial dislocation. The signs of these BPDs are consistent with those predicted from the calculation results, which mitigate compressive and tensile stresses in the epilayer and the substrate, respectively. It is considered that a thicker epilayer increases tensile stress in the substrate, which induces the formation of the BPD with an extra half-plane above the core on the substrate side. The distribution of the BPD half-loop width was also analyzed and compared with the calculated shear stress distribution caused by the radial temperature gradient. Calculations considering the local stress near the triangular defect revealed that the tensile stress near the epi/sub interface locally increases, exceeding the critical stress to form BPD, with an extra half-plane above the core for wafers with an epilayer thickness above 50 μm.